2013 Ford F-350 Super Duty Drivetrains

Below you will find various in-demand Ford Drivetrains, components and accessories for your 2013 F-350 Super Duty. Advance Auto Parts has popular F-350 Super Duty parts like Differentials, Universal Joints, Transfer Cases and more. You’ll also find aftermarket and OEM Drivetrains for other F-350 Super Duty model years including 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022 and more. Select a category of 2013 Ford F-350 Super Duty Drivetrains below and start saving instantly.

Popular 2013 Ford F-350 Super Duty Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

4WD Axle Actuator Housings

Drive Shaft Support Bolts

U-Joints

4WD Hubs

Transfer Case Assemblies

Transmission Transfer Case Motors

Transfer Case Adapter Gaskets

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Axle Shafts

Bearing Pullers

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Locking Hub Service Kits

4WD Switches

Axle Spindle Seals

U-Joint Centering Yokes

Differential Cover Bolts

Input Shaft Pilot Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Axle Vents

Differential Clutch Packs

Differential Ring and Pinions

U-Joint U-Bolt Kits

Differential End Yokes

Spindle Lock Nuts

Drive Shaft Repair Kits

Differential Lock Assemblies

Differential Air System Seal Housings

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Front Differential Cover Gaskets

Rear Housing Cover Gaskets

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Transfer Case Differential Bearings

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Axle U-Bolt Kits

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Oil Pump Housing Seals

Transfer Case Shift Fork Inserts

Differential Drive Pinion Oil Deflectors

Differential Carrier Bolts

Differential Pinion Gear Washers

Output Shaft Pilot Bearings

Axle Shaft Bolts

Differential Ring and Pinion Kits

Limited Slip Differential Assemblies

4WD Actuator Connectors

Differential Clutch Pack Clips

Differential and Pinion Shim Kits

Universal Joint Snap Rings

Axle Shaft Flange Caps

Essential Drivetrains for 2013 Ford F-350 Super Duties

from

$138.99

Product Features:

KIT – INT. DANA 70 OPEN 35 SPL.

from

$1029.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$20.99

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$1195.00

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit fits full floating applications only.

Product Features:

Fits Ford 10.25″ and 10.5″
Clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$334.99

Yukon replacement yoke for Dana 80 with a 1410 U/joint size. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 80
37 spline
1410 u-joint size
4.188″ snap ring span
1.188″ cap diameter
Outside snap ring design
Strap style

from

$31.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$8.99

10.25″ Ford TracLoc pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer
Fits Ford 10.25″ with Trac Loc positraction

from

$289.99

This kit uses Koyo bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and br

Product Features:

Fits Dana Ford 10.25″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

from

$53.99

1330 Yukon Lifetime U/Joint. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$5.99

Product Features:

Pinion nut washer
Fits Dana Spicer 80

from

$143.99

Product Features:

MINI INSTALL KIT DANA 80

from

$6.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$409.99

Yukon standard open spider gear kit for 10.25″ & 10.5″ Ford with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Ford 10.25″ open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$25.99

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$15.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$323.99

Yukon flange yoke for Ford 10.25″ and 10.5″ with short spline pinion. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 1993 and up Ford 10.25″
31 spline
Round companion flange

from

$41.99

Product Features:

Cross pin shaft
Fits Dana Spicer 50

from

$7.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$289.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits 1993 – 1999 Ford 10.25″
10.25″ ring gear diameter
31 spline pinion
12 ring gear bolts
4.88 ratio

from

$11.99

TCaseShiftForkInsert

from

$889.99

Differential

from

$59.99

The components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of an axle of a vehicle or trailer. Check the leaf spring dimensions and other relevant application details to select the right type and size U-bolt kit for your needs.

Product Features:

Reliable hardware – the components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of a vehicle or trailer axle
Check fit – carefully review the dimensions of the leaf springs that will be used and other relevant application details to select the right type and size U-bolt kit for your needs
Durable construction – the components in this kit are engineered from quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$319.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 front
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$23.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$28.99

Product Features:

Oil baffle
Fits Dana Spicer 50

Upgrade your 2013 Ford F-350 Super Duty with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 2013 Ford F-350 Super Duty, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your F-350 Super Duty functioning at its best. At Advance Auto Parts, we offer a wide selection of 416 Drivetrains for the 2013 Ford F-350 Super Duty, designed to meet your needs without breaking the bank. From Differential replacements to Universal Joints upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 2013 Ford F-350 Super Duty at great prices. Our Drivetrains inventory for this model ranges from just $2.99 to $3,524.99, with an average price of $397.00. Our 416 Drivetrains in stock come from 18 trusted brands, so you’re sure to find the right part for your 2013 Ford F-350 Super Duty without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2013 Ford F-350 Super Duty, we stock popular OEM and aftermarket Drivetrains from top names like Moog, National, DriveWorks, and more. Moog Drivetrains start at just $9.99 and boast an impressive 4.5 stars average rating from customers. National and DriveWorks also bring quality to the table, with Drivetrains available starting at $7.99, and at an average 4.3 stars rating. With 7,205 customer reviews and counting, our 2013 Ford F-350 Super Duty Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2013 Ford F-350 Super Duty is always ready to roll. We’re committed to providing you with everything you need to keep your F-350 Super Duty in top shape, all in one place. Start shopping confidently below for your 2013 Ford F-350 Super Duty!

Best-Selling Differentials for 2013 Ford F-350 Super Duties

Enhance the driving experience in your Ford with 266 quality Differential components, starting at $2.99.

show more show less

from

$14.49

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$10.49

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$69.99

Valvoline SAE 75W-140 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our formulation provides exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity and wear resistance, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. It’s recommended for conventional rear axles and transmissions requiring EP gear lubes under high speed, high load, high torque and high horsepower conditions.

Product Features:

EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -22F to 390F degrees
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$10.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$16.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$38.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$18.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$11.99

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands of many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON*, DEXRON*-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$18.99

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations.
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

from

$74.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$4.99

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
1/2″ x 18 thread

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$23.49

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.99

Repleacement ring gear bolt for Dana 80. 9/16″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 80
9/16″ x 18 thread

from

$38.49

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.79

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$13.99

Product Features:

Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

from

$23.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$30.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$27.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Most Popular 2013 Ford F-350 Super Duty Universal Joints

Customize your Ford with 52 Universal Joints products like U-Joints, U-Joint Strap Kits, and U-Joint U-Bolt Kits, all priced under $999.99.

show more show less

from

$54.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$9.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 330 & 331
Contains two 1.81″ bolt center clamps and four 5/16-24 x 3/4″ cap screws

from

$54.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$59.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$46.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$33.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$37.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$37.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$46.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$54.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$73.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$46.49

Product Features:

Journal cross is engineered with a solid cold-formed body to ensure better wear and overall strength.
Bearing cups are heat treated for strength; precision-ground and case-hardened for durability.
Multi-lip seal keeps grease in and contaminants out, and gets maximum retention in a wider range of environments.
Thrust washers eliminate metal-to-metal contact, prevent wear and lower the overall operating temperature.

from

$37.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$72.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

from

$16.99

1350 & 1410 U/joint U-bolts, 3/8″ X 1-11/16″, kit.

Product Features:

u-joint u-bolt kit
Fits 1350 and 1410 u-joint size
Includes two u-bolts and four nuts

from

$68.99

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$63.99

Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.

from

$61.99

Yukon 1330 Dual-size cap U/Joint. 3.625″ snap ring span. One set of caps is 1.125″ in diameter and the other is 1.062″. Outside snap ring.

Top Picks for 2013 Ford F-350 Super Duty Transfer Cases

Upgrade Ford F-350 Super Duties with top-quality Transfer Cases parts, including 18 OEM and aftermarket selections for your 2013 model.

show more show less

from

$17.99

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$36.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$7.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$229.99

Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:

Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications
Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion
100% new – this transfer case motor is entirely new, not remanufactured like competitors
Quality assured – vehicle-specific application has been validation tested to ensure quality

from

$158.99

CARDONE Remanufactured Transfer Case Motors are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. Each unit is 100 percent computer tested at three points during the remanufacturing process to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance with our direct-replacement transfer case motors.

Product Features:

All motors are 100 percent torque tested to ensure strength for proper gear engagement.
Each unit is 100 percent computer tested at 3 points during the remanufacturing process for guaranteed performance.
Every motor is assembled with the precise amount of lubricant to ensure quiet operation and long life.
Motor magnets are 100 percent recharged for superior performance and reliability.
Transfer case motor sensors are 100 percent replaced with new, O.E.-quality sensors for superior performance and long product life.
As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.

from

$23.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$31.49

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$26.99

Meets or exceeds all original equipment specifications
Application specific, providing unsurpassed quality for a seal you can trust
Validated for fit, form, and function
Engineered for the sealing repair environment
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$31.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$9.99

Design type: springless; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$16.99

TCaseOutputShaftSeal

from

$26.49

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Transfer Case NP271 & NP273 Rear Case Half 1998+

from

$389.99

USA Standard Gear produces top quality transfer case small parts for repair and maintenance, including full top-to-bottom overhauls and rebuilds. USA Standard has one of the largest inventories of OEM and aftermarket transfer case component parts in the industry. Our large inventory and experienced tech support are two of the reasons we have been an industry leading supplier for decades. When you chose our transfer case small parts, you know you’re going to get the right part in stock backed by in-house quality assurance testing and expert knowledge.

Product Features:

NP271 & NP273 Transfer Case (New Process)
Rear Case
Cast # 24278
1998 and newer

from

$16.99

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$11.99

Shift Fork Insert

from

$11.99

TCaseShiftForkInsert

from

$11.29

TCaseOutputShaftSeal

from

$7.59

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

In-Demand Drive Shafts and Axles for 2013 Ford F-350 Super Duties

Select from 64 premium Drive Shafts and Axles parts for your 2013 Ford F-350 Super Duty, with prices ranging from $7.99 to $1,107.99.

show more show less

from

$45.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$69.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$22.49

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$44.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$86.99

from

$45.99

from

$20.99

The axle shaft o-ring seals the rear axle to the wheel hub. The symptom of a failed axle shaft o-ring is an axle fluid leak around wheel hub. This is an ideal repair solution to prevent axle fluid leaks from forming around the wheel hub.

Product Features:

Aftermarket exclusive replacement part
Recommended for replacement when servicing vehicle brakes
Direct replacement for original equipment
This part has undergone extensive vehicle try-on and durability testing to ensure strength, fitment and longevity

from

$21.99

Aftermarket exclusive replacement part
Recommended for replacement when servicing vehicle brakes
Direct replacement for original equipment
This part has undergone extensive vehicle try-on and durability testing to ensure strength, fitment and longevity

from

$196.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Hardware not included
Mounting Hole Quantity: 2
Mounting Hole Center To Center: 6.620 In
Bearing/Cone Inside Diameter: 1.378 In
Material: Steel

from

$122.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to FORD 03-15;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 2003-2015
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.75 INCH / 70 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: HORSESHOE
WITH PLATE
WITHOUT STUDS

from

$422.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$83.99

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$8.99

This axle vent is designed to match the fit and function of the original vent on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this axle vent is designed to match the fit and function of the original vent on specified vehicles
Restores functionality – reliable replacement for an original vent that has failed due to blockage or fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.99

Product Features:

Pinion yoke dust shield
Fits Dana Spicer 60 and 70

from

$56.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to FORD 08-15;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 2008-2015
Weight approx: 3 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.65 INCH / 67 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: HORSESHOE

from

$7.99

AxleHubBolt

from

$279.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$1107.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1048.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1037.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1029.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$980.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$910.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

Most Sold 2013 Ford F-350 Super Duty 4WD Components

Explore our best-selling Ford parts for the 2013 F-350 Super Duty among 10 OEM and aftermarket options starting from $33.99.

show more show less

from

$621.99

All metal construction. ZA alloy dial. Thick internal wave spring. Heavy duty detents.

Product Features:

9/10 Turn Dial
Heavy Detents For Positive Engagement
Wave Spring Technology
All Metal Construction
Alloy Dial With Dual Seals

from

$56.99

This 4WD hub locking solenoid directly replaces the original equipment solenoid on certain vehicle years, makes and models.

Product Features:

Direct replacement – this 4WD hub locking solenoid matches the fit and function of the stock solenoid on certain vehicle applications
Effective fix – restores control of 4WD system impacted by failed original solenoid
Thoroughly tested – on-vehicle and laboratory testing ensures trouble-free operation
Trustworthy quality – backed by team of designers and engineers in the United States

from

$159.99

Four-wheel drive malfunctioning due to a bad locking hub? This locking hub directly replaces the original equipment hub on specific vehicles years, makes and models.

Product Features:

Direct replacement – this locking hub matches the fit and function of the original equipment hub on specific vehicles
Effective fix – replacement restores 4WD operation after original equipment hub fails
Thoroughly tested – vehicle try-on testing and rigorous quality control measures ensure longevity
Trustworthy quality – backed by team of designers and engineers in the United States

from

$619.99

All metal construction. ZA alloy dial. Thick internal wave spring. Heavy duty detents.

Product Features:

9/10 Turn Dial
Heavy Detents For Positive Engagement
Wave Spring Technology
All Metal Construction
Alloy Dial With Dual Seals

from

$71.99

Carquest Premium Vehicle Solutions provides high-quality solutions for a wide range of applications. The 4WD Actuator ensures seamless transition between 2WD and 4WD modes, providing enhanced traction and stability on challenging terrains without manual intervention. Engineered for maximum performance and durability, our products are built to excel in even the most demanding conditions, ensuring reliable operation and long-lasting value.

Product Features:

Durable Construction: Designed with high-quality materials to withstand harsh environmental conditions, ensuring long-lasting performance in extreme temperatures, vibrations, and moisture exposure.
Precision Engineering: Accurate sensing and switching capabilities provide reliable performance, reducing the risk of malfunctions and improving vehicle safety and efficiency.
Easy Installation & Maintenance: Designed for quick installation and minimal upkeep, reducing downtime and repair costs for both manufacturers and consumers.
Fit/Form/Function: Each vehicle electronic component is engineered to meet or surpass OEM standards, ensuring precise fit, optimal functionality, and reliable performance.

from

$33.99

Durable Construction: Designed with high-quality materials to withstand harsh environmental conditions, ensuring long-lasting performance in extreme temperatures, vibrations, and moisture exposure.
Precision Engineering: Accurate sensing and switching capabilities provide reliable performance, reducing the risk of malfunctions and improving vehicle safety and efficiency.
Easy Installation & Maintenance: Designed for quick installation and minimal upkeep, reducing downtime and repair costs for both manufacturers and consumers.
Fit/Form/Function: Each vehicle electronic component is engineered to meet or surpass OEM standards, ensuring precise fit, optimal functionality, and reliable performance.

from

$74.99

The main device in any electrical circuit is a switch. In an electrical circuit a device is required to turn a component on or off when commanded by the operator, within the switch are contacts that will complete the electrical path to the load, or driven device. The operation of a switch may be manual from a person or could be electrical from some sort of controller or computer.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
Where applicable electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.

from

$74.99

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
Where applicable electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.

from

$67.99

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
Where applicable electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.

from

$43.49

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

Top-Rated Drivetrains Brands For Your 2013 Ford F-350 Super Duty

Shop for the best-rated brands offering Drivetrains and other products for your 2013 Ford F-350 Super Duties. Below you’ll find some of our best rated Drivetrains from Moog, National, and DriveWorks, and more. Drivetrains from these brands that fit a 2013 F-350 Super Duty start at just $7.99 and are rated as high as 4.5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Moog 2013 Ford F-350 Super Duty Drivetrains

When it comes to maintaining or upgrading your 2013 Ford F-350 Super Duty, using quality Drivetrains is essential to ensure durability and a perfect fit. Moog ticks all of those boxes. We offer a wide selection of Moog Drivetrains, specifically designed for the 2013 Ford F-350 Super Duty. With over 3 Moog brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $9.99, with an average price of just $41.66. Plus, with over 74 customer reviews and an average rating of 4.5 stars, you can trust that our Moog Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $9.99

(10)

Universal Joint Strap Kit

“Replaced my factory junk with this kit. Now I will be able to work on it in the future.”

from $54.99

(25)

Greaseable Premium Universal Joint

“I trust Moog I’m sure it will be on my truck for a while.”

from $59.99

(39)

Greaseable Super Strength Universal Joint

“quality product”

Popular National 2013 Ford F-350 Super Duty Drivetrains

National auto parts is one of the highest quality Drivetrain brands in the market. Any 2013 Ford F-350 Super Duty owner should feel confident when installing genuine National parts in their vehicle. To ensure the best fit and performance for your 2013 F-350 Super Duty, Advance Auto Parts carries a full inventory of 3 National Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these National Drivetrains range from $14.49 to $69.99, plus, with more than 16 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $14.49

(3)

Axle Spindle Seal

“quality seal that replaced the motorcraft version for a better price on my 2005 f250”

from $17.99

(7)

Multi-Purpose Bearing

“National bearings amazingly made in USA. Did the job.”

from $69.99

(6)

Multi-Purpose Seal

“Fair price with speed perks, seems to be working good”

FAQs for 2013 Ford F-350 Super Duty Drivetrains

Which Drivetrains are best-sellers for 2013 Ford F-350 Super Duties?

Out of 416 Drivetrains that fit 2013 Ford F-350 Super Duties, the following parts are the top sellers:

DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart (12079139) – $11.99
Flex Fill Transmission & Differential Gear Oil: Full Synthetic 75W-90, 1 Quart (12507273) – $18.99
Greaseable Super Strength Universal Joint (10086981) – $59.99

What’s the price range for 2013 Ford F-350 Super Duty Drivetrains?

Drivetrain prices for the 2013 Ford F-350 Super Duty start at $2.99 and go up to $3,524.99 for the most premium parts.

What’s the average price of a Drivetrain for a 2013 Ford F-350 Super Duty?

The average price for Drivetrains for the 2013 Ford F-350 Super Duty is $397.00. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford F-350 Super Duty model years?

Yes, we currently carry Drivetrains for 25 model years of Ford F-350 Super Duties between 1999 and 2025. Drivetrains are bought most frequently for the following model years: 2022, 2021, 2020, 2019, 2018, 2017, 2016, 2015, and 2014.

What are the cheapest Drivetrains for my 2013 Ford F-350 Super Duty?

The cheapest 2013 Ford F-350 Super Duty Drivetrains we carry in stock are:

Ring Gear Bolt (20520495) – $2.99
Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (11643194) – $3.99
Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (11643357) – $4.99
Side Gear Thrust Washer For Dana 60, 70 & 80 (11642996) – $4.99
Dana 60, Dana 70 & Dana 80 Cover Bolt (11642999) – $5.99

What are the top-rated Drivetrains that fit the 2013 Ford F-350 Super Duty?

Out of 7,205 reviews by customers, our 2013 Ford F-350 Super Duty Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 2013 Ford F-350 Super Duty and their top-rated products:

Spindles
- Axle Spindle Seal (11077032) – $14.49
Universal Joints
- Axle Spindle Seal (11077032) – $14.49
4WD Components
- Axle Spindle Seal (11077032) – $14.49

What types of Drivetrains do you sell for my 2013 Ford F-350 Super Duty?

As of 11/2/25, these are some of the most in-demand types of Drivetrains for a 2013 Ford F-350 Super Duty:

Can I get help with 2013 Ford F-350 Super Duty Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford F-350 Super Duty Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford F-350 Super Duty Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

2013 Ford F-350 Super Duty Drivetrains

Motive Gear – Differential Carrier Gear Kit (Part No.706058XR)

Dorman – Drive Shaft: Greaseable, Adjustable (Part No.976-736)

FAG US – Shaft Seal (Part No.SS2852)

Yukon Gear – Dura Grip For Ford 10.25" & 10.5" (Part No.26031)

Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)

Yukon Gear – Replacement Yoke For Dana 80 With A 1410 U/Joint Size (Part No.41034)

National – Shaft Repair Sleeve (Part No.99225)

Yukon Gear – 10.25" Ford Tracloc Pinion Gear Thrust Washer (Part No.33290)

USA Standard Gear – Bearing Kit For Ford 10.25" (Part No.58005)

Yukon Gear – 1330 Lifetime U/Joint (Part No.42004)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)

Yukon Gear – Replacement Pinion Nut Washer For Dana 80 (Part No.33165)

Motive Gear – Differential Gear Install Kit (Part No.D80IK)

Pro-King – Differential Pinion Nut (Part No.764A961)

Yukon Gear – Standard Open Spider Gear Kit For 10.25" & 10.5" Ford With 35 Spline Axles (Part No.16012)

FAG US – Shaft Seal (Part No.SS3144)

Yukon Gear – Outer Oil Slinger For Ford 7.5", 8.8", 9", 10.25" (Part No.33022)

National – Bearing Race (Part No.HM88610)

Yukon Gear – Flange Yoke For Ford 10.25" And 10.5" With Short Spline Pinion (Part No.41044)

Yukon Gear – Replacement Cross Pin Shaft For Spicer 50, Standard Open (Part No.33440)

Driveworks – Needle Bearing (Part No.S-B-2110)

USA Standard Gear – Ring & Pinion Gear Set For Ford 10.25" In A 4.88 Ratio (Part No.36110)

USA Standard Gear – TCaseShiftForkInsert (Part No.70666)

Yukon Gear – Differential (Part No.26042)

Dorman – U-Bolt Repair Kit (Part No.929-798)

Yukon Gear – Pinion Install Kit For Dana 60 Front Differential (Part No.13093)

National – Multi-Purpose Seal (Part No.710653)

Yukon Gear – Replacement Oil Baffle For Dana 50 (Part No.33005)

Valvoline – DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.822405)

Felpro – Axle Housing Cover Gasket Irregular Shaped 12 Bolt Hole Gasket (Part No.RDS 55394)

Valvoline – SynPower Transmission & Differential Gear Oil: Full Synthetic 75W-140, 1 Gallon (Part No.887344)

National – Bearing Race (Part No.382A)

Felpro – Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (Part No.RDS 55447)

National – Tapered Roller Bearing Cone (Part No.HM89443)

Driveworks – Taper Bearing Cone (Part No.S-LM-104949)

Driveworks – Tapered Cone Wheel Bearing Assembly (Part No.S-387-AS)

Valvoline – DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart (Part No.798153)

Valvoline – Flex Fill Transmission & Differential Gear Oil: Full Synthetic 75W-90, 1 Quart (Part No.889785)

Dorman – Differential Cover (Part No.697-704)

Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)

Yukon Gear – Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (Part No.33037)

Yukon Gear – Chrysler 9.25" And Dana 44 / 60 Tracloc Clutch Guide Replacement (Part No.33249)

Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)

National – Tapered Roller Bearing Cone (Part No.HM88542)

Yukon Gear – Repleacement Ring Gear Bolt For Dana 80 (Part No.33039)

National – Tapered Roller Bearing Cone (Part No.HM803146)

National – Bearing Race (Part No.HM88510)

Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 70, 70HD, 70U & 80 (Part No.55011)

National – Bearing Race (Part No.453X)

National – Differential Pinion Seal (Part No.100727)

Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)

National – Bearing Race (Part No.HM89411)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.374)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.331-10)

Spicer – Universal Joint (Part No.5-1410X)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.295)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.330)

Driveworks – Universal Joint (Part No.DW-374)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.232)

Driveworks – Universal Joint (Part No.DW-331)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.231)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.331)

Driveworks – Universal Joint (Part No.DW-330)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.351)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.271)

Yukon Gear – 1310 U/Joint With Zerk Fitting On Cross (Part No.42008)

Spicer – Universal Joint, Greaseable 1480 Series OSR (Part No.5-188X)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.296)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.272)

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)

Yukon Gear – 1350 & 1410 U/Joint U-Bolts, 3/8" X 1-11/16", Kit (Part No.41190)

Spicer – Universal Joint (Part No.SPL55X)

Yukon Gear – 1310 To Mechanics 3R Adapter U/Joint (Part No.42013)

Yukon Gear – 1350 Lifetime Series U/Joint (Part No.42021)

Yukon Gear – 1330 Dual-Size Cap U/Joint (Part No.42017)

National – Multi-Purpose Bearing (Part No.B-2110)

National – Shaft Repair Sleeve (Part No.99187)

Driveworks – Needle Bearing (Part No.S-B-2110)