2013 Chevrolet Express 1500 Belts and Hoses
More 2013 Chevrolet Express 1500 Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2013 Chevrolet Express 1500, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2013 Chevrolet Express 1500 Belts and Hoses
Dayco – Serpentine Demanding Drive Kit; With Belt, Pulley and Tensioner, 3 Piece Set (Part No.D60960K1)
from
$99.99
Engineered specifically for the most problematic drive systems as an improvement over the OE design, Dayco demanding drive kits come in 14 applications that contain all necessary front-end accessory components to ensure a safe, reliable and noise-free belt drive system. Each kit includes up to two serpentine belts, a premium tensioner with flat spring technology and an idler pulley.
Product Features:
See More
Product Features:
- Custom engineered to cover 35 million problem drive vehicles in operation
- Designed as an improvement over OE to address problematic drive systems
- Features a specially designed serpentine belt with specific compounds that mitigate noise
Dayco – Serpentine Demanding Drive Kit; With Belt, Pulley and Tensioner, 3 Piece Set (Part No.D60930K1)
from
$99.99
Engineered specifically for the most problematic drive systems as an improvement over the OE design, Dayco demanding drive kits come in 14 applications that contain all necessary front-end accessory components to ensure a safe, reliable and noise-free belt drive system. Each kit includes up to two serpentine belts, a premium tensioner with flat spring technology and an idler pulley.
Product Features:
See More
Product Features:
- Custom engineered to cover 35 million problem drive vehicles in operation
- Designed as an improvement over OE to address problematic drive systems
- Features a specially designed serpentine belt with specific compounds that mitigate noise
GM Genuine Parts – Crankcase Vent Hose (Part No.12556932)
from
$47.99
GM Genuine Parts PCV Valve Hoses are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
GM Genuine Parts – Positive Crankcase Ventilation (PCV) Hose (Part No.12582227)
from
$40.99
GM Genuine Parts PCV Valve Hoses are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
ACDelco – Serpentine Idler/Tensioner Pulley: Direct Fit, Steel, 88.9 mm Diameter (Part No.15-20676)
from
$27.49
ACDelco Gold (Professional) Accessory Drive Belt Idler Pulleys are a high quality alternative to Original Equipment (OE) parts. ACDelco Gold (Professional) parts are manufactured to meet your expectations for fit, form, and function, making them a smart choice for General Motors vehicles, as well as most makes and models, including special applications. These high-quality parts are backed by General Motors. Some ACDelco Gold parts may have formerly appeared as ACDelco Professional.
Product Features:
See More
Product Features:
- Some ACDelco Gold parts may have formerly appeared as ACDelco Professional
- Premium aftermarket replacement part
- Manufactured to meet specifications for fit, form, and function for General Motors vehicles as well as most makes and models
Dayco – Serpentine Idler/Tensioner Pulley; Direct Fit, 90 mm Diameter, 30 mm Smooth (Part No.89006)
from
$30.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Yukon Gear – Seal Puller Tool (Part No.56063)
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Dorman – Engine Oil Cooler Line (Part No.625-152)
from
$34.99
This engine oil cooler hose assembly matches the fit and function of the original equipment components for reliable repair and restoration of proper oil circulation between the oil cooler and engine.
Product Features:
See More
Product Features:
- Ideal replacement – this engine oil cooler hose assembly is a direct replacement for the original hose assembly
- Quality materials – this engine oil cooler hose assembly is made from corrosion-resistant materials to ensure the smooth transfer of oil from the engine to the cooler
- Easy to install – no special tools required
- Quality tested – rigorous quality control ensure this hose assembly conforms to product standards
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 31" Long, 1.28" Diameter (Part No.E72377)
from
$56.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 27" Long, 1.28" Diameter (Part No.E72136)
from
$22.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 15.25" Long, 1.50" Diameter (Part No.D71426)
from
$29.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Molded Heater Hose; EPDM Rubber, 1/4 Inch Diameter, 29 1/2 Inch Length (Part No.86836)
from
$33.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Poly Rib Belt Serpentine Belt; 96.06 Long, 6 Rib Count (Part No.5060960)
from
$65.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Poly Rib Belt Serpentine Belt; 95.08 Long, 6 Rib Count (Part No.5060950)
from
$58.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Gates – DriveAlign« Automatic Belt Drive Tensioner (Part No.38158)
from
$56.99
Gates is a global leader in Original Equipment (OE) System Design. With a full line of tensioners globally, you can count on Gates to supply premium quality DriveAlign Automatic Belt Tensioners you can depend on.
Product Features:
See More
Product Features:
- Comprehensive line includes parts to fit cars, vans, SUVs and light trucks, domestic and import (European and Asian)
- Manufactured using the same or improved technology and quality materials as the Original Equipment Manufacturer (OEM) part, assuring a factory match
- Patented labyrinth seal protects internal components to meet or exceed OE life expectancy requirements
- Patented vibration-damping system absorbs extreme vibration to improve tensioner, as well as belt and accessory, life
- Torsional round spring design provides reliability as well as consistent tension
- Comprehensive line includes parts to fit cars, vans, SUV’s and light/heavy-duty trucks.
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999034A)
from
$56.99
This genuine Litens tensioner is manufactured and designed by Litens, the world’s largest manufacturer of belt tensioners. To address shortcomings and common failure points of the original tensioner, Litens has released this new and improved design. A 20% increase in tension results in less noise and belt slip. The main tensioner pivot has been greatly improved to prevent binding frequently experienced with the original part, and a high speed bearing has been implemented to provide long life and reliability._
Product Features:
See More
Product Features:
- the world’s largest manufacturer of belt tensioners. To address shortcomings and common failure points of the original tensioner.
- Litens has released this new and improved design. A 20% increase in tension results in less noise and belt slip. The main tensioner pivot has been greatly improved to prevent binding frequently experienced with the original part
- and a high speed bearing has been implemented to provide long life and reliability.
- Professional Mechanics will change this tensioner in approx. 20 minutes.
- Due to the fact that belts and tensioners have similar Original Equipment “design life targets”, it is often a best practice to replace the belt tensioner when replacing a worn or broken belt. Belt removal is required to change the tensioner. Therefore, d
- Installation instructions included.
Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100027998MBL)
from
$16.31
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
Bando – Drive Belt (Part No.W10002440755BAN)
from
$43.25
Drive Belt
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 12 Inch Length (Part No.88431)
from
$14.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 6 Inch Length (Part No.87661)
from
$37.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Molded 90 Degree Heater Hose (Part No.28474)
from
$14.79
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
Product Features:
See More
Product Features:
- Resists electrochemical degradation and water permeation
- Use with heater hose connectors and bulk heater hose to create custom assemblies
- Compatible for coolant, air and water applications
- EPDM tube and cover, synthetic fiber reinforcement
- SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
- Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
INA – Acc. Belt Tension Pu (Part No.G6011117822INA)
from
$84.57
Acc. Belt Tension Pu
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 76 mm Diameter (Part No.900027A)
from
$28.99
This pulley is manufactured by Litens Automotive the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Heavy duty thermoplastic construction for long life and trouble-free performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by Litens, the largest original equipment tensioner and pulley supplier in the world, to ensure proper form, fit, and performance
- Heavy Duty Glass Reinforced Polymer Pulley for optimized dimensional control and running surface durability
- OE-spec sealed ball bearings with synthetic grease and double lip seals for long life
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter (Part No.900401A)
from
$66.99
This Litens pulley is supplied by one of the largest original equipment suppliers in the world and meets all form, fit, and performance characteristics of the original equipment part . Like the G.M. Original Equipment pulley, the Litens replacement part is constructed of heavy duty steel for long life and trouble free performance. This pulley is supplied with a new integrated bolt/dust shield to facilitate installation. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the world’s largest Original Equipment suppliers of accessory drive tensioners and pulleys
- Heavy Duty Steel Pulley
- Pre-assembled pulleys save installation time and ensure that all components are assembled to original specifications for both installation and performance
- Precision steel stamping with close tolerance ball bearing pocket.
- Electro-deposited coating (e-coat) for superior corrosion resistance.
- Running surface designed and engineered for proper belt tracking.
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 12 1/4 Inch Length (Part No.87668)
from
$20.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.19761)
from
$74.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 6 Inch Length (Part No.80400)
from
$18.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Popular 2013 Chevrolet Express 1500 Belts and Hoses Categories
2013 Chevrolet Express 1500 Belts and Hoses
You count on your 2013 Chevrolet Express 1500 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 70 Belts and Hoses ranging in price from $0.99 to $183.99, you’re sure to find everything you need for your 2013 Chevrolet Express 1500.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 11 different brands like Dayco, Driveworks, and Litens. 2013 Chevrolet Express 1500 Belts and Hoses start as low as $0.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 5,275 extensive product reviews on 2013 Chevrolet Express 1500 Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Serpentine Belt Tensioner; 1 Piece, HD, Built To Outperform And Outlast OE Parts with 4.6 stars and Poly Rib Belt Serpentine Belt; 87.6 Long, 6 Rib Count with 4.5 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2013 Chevrolet Express 1500 below to get started!
Top-Rated Belts and Hoses Brands For Your 2013 Chevrolet Express 1500
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2013 Chevrolet Express 1500 running right for years to come. In our inventory you’ll find brands like Dayco, Driveworks, Litens, and even more.
Popular Mitsubishi Belts and Hoses
You’ll find popular Mitsubishi brand products across Serpentine and V Belts. All are waiting to get your 2013 Chevrolet Express 1500 back on the road. Some of the top-rated Mitsubishi products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2013 Chevrolet Express 1500, and some of our most reviewed Dayco parts include:
from
$30.99
(516)
Serpentine Idler/Tensioner Pulley; Direct Fit, 90 mm Diameter, 30 mm Smooth
Belt Tensioner Pulleys
from
$24.99
(251)
Serpentine Idler/Tensioner Pulley; Polymer, 76mm Dia., 28.7mm Width, 6 Grooves
Belt Tensioner Pulleys
FAQs for 2013 Chevrolet Express 1500 Belts and Hoses
What are the most purchased Belts and Hoses for the 2013 Chevrolet Express 1500?
Out of 70 Belts and Hoses for the 2013 Chevrolet Express 1500, the most popular in our inventory are:
What are the top-rated 2013 Chevrolet Express 1500 Belts and Hoses?
Top-rated Belts and Hoses for your 2013 Chevrolet Express 1500 based on customer reviews/ratings are:
from
$53.99
(143)
Serpentine Belt Tensioner; 1 Piece, HD, Built To Outperform And Outlast OE Parts
“Worked as intended”
