from

$363.99

Yukon spider gear kit for Ford 8.8″, 31 spline, Trac Loc posi. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects. This kit does not include cross pin shaft or clutches.

Product Features:

Spider gear kit
Fit Ford 8.8″ Trac Loc positraction with 31 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$49.99

Cross pin shaft for 9.75″ Ford.

Product Features:

Cross pin shaft
Fits Ford 9.75″

from

$499.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits Ford 10.25″
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve , marking compound and brush.

from

$14.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$5.99

Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt. 7/16″ head, .925″ long.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
7/16″ head
.925″ long

from

$538.99

RngPnn

from

$16.29

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$45.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$579.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. This unit uses the factory side gears.

Product Features:

Fits Ford 8″ and 9″ with 28 or 31 spline axles
Made from 9310 steel for added strength
Works with stock side gears in standard carrier case

from

$11.99

Pilot bearing retainer for Ford 9″.

Product Features:

Pilot bearing retainer for Ford 9″

from

$289.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits standard rotation Dana Spicer 44 front
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers, thread locker, marking compound with brush and gasket.

from

$6.99

Product Features:

D30 PRE-LOAD SPACER (SHIM PACK)

from

$249.99

9.75″ TracLoc clutch set, 16 Pieces (does not include belleville).

Product Features:

Clutch kit
Fit Ford 9.75″ Trac Loc positraction

from

$12.99

8.8″ Ford cover gasket.

Product Features:

Cover gasket
Fits Ford 8.8″

from

$8.99

10.25″ Ford TracLoc pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer
Fits Ford 10.25″ with Trac Loc positraction

from

$349.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9.75″
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$38.99

8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:

Pilot bearing
Fits Ford 9″
0.656″ thick

from

$121.99

Yukon replacement yoke for Dana 30, 44, and 50 with fine spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
Strap style

from

$128.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 44 differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Dana Spicer 44
Includes carrier bearings and races and carrier shim kit

from

$13.59

Product Features:

FORD 9″ CROSS PIN

from

$12.99

Valvoline ATF for MERCON®V Applications is a high-quality transmission fluid meeting and exceeding the requirements of the Ford Mercon V specification which covers most Ford passenger cars and light-duty trucks (except those specifying MERCON®SP, MERCON®LV or Type F fluids), including Lincoln and Mercury, as well as most pre-2006 GM vehicles and many imports. Recommended for use in the following applications: MERCON®V, MERCON®, DEXRON®-III, DEXRON®-II, Caterpillar TO-2, Allison C-4. Other applications include Power steering fluid where a DEXRON® or MERCON® fluid is recommended. Suitable to use in Nissan Matic D, Matic J and Matic K.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$789.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″ with 28 spline axles
Trac Loc positraction
Clutch style positraction
Street design
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$351.99

Yukon right hand axle for ’09-’14 Ford F150. 33.75″ long, 6 lug, 34 spline, 1.705″ bearing journal. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects.

Product Features:

Fits 2009-2014 Ford F150 9.75″ rear differential
Right hand side
33 3/4″ long
34 spline
1.705″ bearing journal
6 lug

from

$519.99

Yukon positraction internals for Ford 9.75″ Dura Grip posi, 34 spline. This kit fits Yukon Dura Grip ONLY. Will not work with factory trac Loc. This kit does not include clutches.

Product Features: