2011 Ford Expedition Differentials

Product Features:

• Crush sleeve spacer for Ford 9.75″
• 0.280″ tall

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Replacement pinion nut for Model 20 & 35, Dana 30 JK, 44 JK front, Ford 10.25″, 10.5″ & some 9.75″. 7/8-20 thread, 1 1/8 socket.

Product Features:

• Pinion nut for Jeep JK front, Jeep Liberty front, Ford 9.75″, 10.25″, 10.5″ and AMC Model 20 and Model 35
• 7/8″ x 20 thread
• 1 1/8″ socket

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Ford 9.75″
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Product Features:

• Spider gear kit
• Fits Ford 8.8″ 28 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Product Features:

• Trac Loc positraction
• Fits Ford 8.8″ with 31 spline axles

SHAFT SEAL

CUP

Side gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.875″ diameter cross pin shaft applications only

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M802011 race
• All steel construction

Max ATF is a synthetic, high-performance, automatic transmission fluid. Its low co-efficient of friction and high film strength help to dramatically reduce heat and wear. Additionally, Max ATF is more oxidation stable than other transmission fluids for longer fluid life. Max ATF significantly reduces heat to extend the life of your transmission.

Product Features:

• High performance automatic transmission fluid
• High film strength helps to dramatically reduce heat and wear
• Fully compatible and can be mixed with other automatic transmission fluids
• Extends the life of your transmission

If you venture off the beaten path, plow snow, or subject your truck or SUV to extreme conditions, this rugged rear differential cover will boost the protection and personality of your vehicle’s drivetrain. Instead of the vulnerable thin stamped steel original equipment cover, this diff cover is precision-engineered from thick ductile iron and boasts an attractive, corrosion-resistant wrinkle coating. Rocks, trail hazards and damaging debris can easily ding an ordinary differential cover, leading to oil leaks and cracks. Plow trucks undergo stress due to the weight of salters and plows, and the no-brakes impacts of hidden potholes, coupled with the corrosive nature of all the salt season after season. This cover also features two filler plugs, which can help ease the difficulties of filling through the factory plug located on the axle housing. The cover is also fitted with a drain plug to make fluid exchanges quick, easy, and remove the need for replacing the differential cover gasket. This extra-rigid replacement will help keep critical components safe while adding a serious cool factor, especially on lifted vehicles. Want to customize your diff even more? We’ve made the stainless steel Dorman logo plate removable so you can replace it with the plate and logo of your choice. The cover comes complete with all necessary bolts and plugs for a complete upgrade..

Product Features:

• Enhanced protection – ideal solution for off-road or snowplow vehicles that need additional protection from damaging rocks and other hazards that can crack an ordinary stamped steel differential cover.
• Precise fit – engineered to exacting specifications to match the fit and function of the original equipment differential cover for a seamless installation on specified Ford and Lincoln vehicles
• Upgraded repair – made from rigid ductile (also known as nodular) iron with an attractive, corrosion-resistant wrinkled finish, and includes required bolts and three plugs for a complete installation and simplified maintenance
• Customize it – includes a stainless steel Dorman logo plate that’s removable so you can replace it with the plate and logo of your choice

Ring&Pinion Gear Set

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

• Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles.
• Quality materials – all components are built for reliable longevity and performance.
• Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
• Trustworthy quality – backed by team of designers and engineers in the United States

Cross pin bolt with 5/16 x 18 thread for 10.25″ Ford.

Product Features:

• Cross pin bolt for Ford 9.75″ and 10.25″ with c-clip axles
• 5/16″ x 18 thread

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits Ford 9.75″
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Ford 8.8″
• Includes carrier bearings and races and “super” carrier shim kit

Product Features:

• F9.75″ RING GEAR BOLT SOLD INDIVIDUALLY

SHAFT SEAL

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

• Fits Ford 8.8″ with 31 spline axles
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

9.75″ Ford Supershim carrier shim kit.

Product Features:

• Super carrier shim kit for Ford 9.75″
• Interlocking design makes installation much easier

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool
• Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9.75″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

• AXLE SHAFT 8.8″ 31 3/4″ R.H. 12&14 MM STUDS

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits 1997-1998 Ford 9.75″
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.