from

$25.99

These high performance thermostats are designed to resist large variations in coolant pressures that occur at high RPM’s where coolant temperature and coolant pressure fight for control of the thermostat keeping it from opening at its designated temperature. The balanced HP thermostat features all brass and copper construction, and opens at the right temperature regardless of engine RPM.

Product Features:

Rated to open at 180 degrees
Opens at right temperature regardless of rpm
Brass and copper construction

from

$33.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$94.99

All modern vehicles consist of several independent operating systems controlled by a main system processor with independent sub-processors. The sub-processors provide class 2 serial information data to the main processor while handling the operation of the system and carry the circuit load to protect the main operating system. When replacing any level processor programming may be needed to enter the unit into the vehicles main operating system.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$10.29

This radiator drain petcock is a direct replacement for the original equipment plug that may have deteriorated or corroded. Made of quality materials, this petcock is engineered to strict standards for durable use over time.

Product Features:

Direct replacement – this radiator drain petcock matches the fit and function of the original equipment part
Durable construction – this part is made of quality materials for a long service life
Saves money – offers original equipment quality at a competitive price
Quality assured – this petcock has undergone virtual testing to assure proper fit and function

from

$26.99

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$8.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$10.49

Cracked or lost the original engine coolant reservoir cap? Replace it seamlessly and effectively with this precisely engineered, direct replacement cap.

Product Features:

Direct replacement – this engine coolant reservoir cap directly replaces a cracked or lost original cap
Application specific – made to match dimensions of reservoir cap on only certain vehicle years, makes and models
Seamless fit – reverse-engineered from the original equipment to fit perfectly
Excellent value – a quick, easy replacement that’s less expensive than going back to the dealership

from

$92.99

Electric fan with 16″ diameter. Imperial electric fans are reversible for push or pull operation and are designed with a thin, aerodynamic profile for applications with limited space.

Product Features:

Rapid-Cool® Thin-Line electric fans
16″ diameter
1,400 CFM
Use as a pusher or puller fan

from

$70.99

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$4.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

from

$45.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

Premium quality materials for longer service life
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$37.99

We are proud to offer this CARQUEST product line: CARQUEST Water Outlets. Our products are engineered and tested to provide years of trouble free operation and designed to be hassle free OE replacement part that meets and/or exceeds OE standards. Backed by over 50 years of mobile temperature control experience, fix it once and fix it right with CARQUST Water Outlets and Thermostat Housings.

Product Features:

Meets and/or exceeds OEM standard
Includes quality gasket or O-ring to ensure proper seal (where applicable)
100% virgin resin material to insure durability
100% leak tested
Direct-fit replacement for ease of installation

from

$287.99

RADIATOR/GRILLE SUPP

from

$119.99

New Platinum Pro Radiator Fan Assembly, 3.8 Liter V6 Engine

Product Features:

3.8 Liter V6 Engine
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$16.79

Crafted to meet the exact specifications set by Original Equipment Manufacturers (OEM), these products are engineered for effortless installation and removal. Constructed from premium-grade components, incorporating proper relief and vacuum valves, they ensure optimal performance even in the most demanding automotive cooling systems. Rigorously quality-tested, these components provide exceptional, out-of-the-box performance and superior durability to meet or exceed the highest standards of today’s vehicles.

Product Features:

Safety lever to vent coolant pressure before removal
Maintains proper cooling system pressure
Easy installation and removal
100% tested to ensure proper pressure and longevity
Meets all OEM specifications

from

$2.09

Water Pipe O-Ring

from

$12.36

Dorman’s Engine Expansion Plugs are available in multiple styles, including Cup Type, Pilot Seal, Reverse Taper, Concave, Quick-Seal® Rubber and Quick-Seal ® Copper. Dorman’s uniquely designed Pilot Seal Expansion Plug ensures a leak-proof fit. Dorman also offer Engine Expansion Plug Kits.

Product Features:

Many sizes available
Conveniently available in packs of different quantities
Constructed from high quality steel, copper, brass, or rubber
Dorman’s Engine Expansion Plugs are constructed to strict engineering quality standards

from

$92.99

US Motor Works Professional Series Water Pump with Fan Clutch are designed to replace the mechanical components of a cooling system. A proper water pump replacement should include a new fan clutch as the two are connected to the same shaft and work together to move the air and cooling fluid. Replacing one without the other can damage the new part and cause repeat work or engine trouble. This matched set will allow your vehicle continued operation in the demanding environment of today’s engine. All components are brand new and QA inspected for perfect fit and function. Restore your cooling power by installing a US Motor Works Professional Series Water Pump with Fan Clutch.

Product Features:

Fan clutch mounts to the water pump and should be replaced at the same time.
Matched set for proper water pump or fan clutch replacement
Includes mounting hardware, gaskets and accessories as required.
Complete mechanical cooling parts replacement
Factory tested and 100% new product
Meets or exceeds OEM quality

from

$25.49

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

Limited 12 Month Or 12,000 Mile Warranty

from

$19.99

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 1 minute

from

$17.49

Permatex’s The Right Stuff 90 Minute Series offers the fastest return to service in a in just 90 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 90 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 90 minutes

from

$34.99

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$62.99

Product Features:

Designed, tested, and built by application
OE performance, fit, and appearance
Precision machined
Out of box installation

from

$2.99

MAHLE gaskets provide world class sealing products trusted by OEMs & Technicians around the globe.

Product Features:

All MAHLE gaskets meet or exceed the original equipment specifications providing the finest sealing products available
MAHLE gaskets utilizes OE equivalent or better materials in all our gaskets
MAHLE gaskets is the leader in Domestic, Asian and European applications
The contents of MAHLE gaskets are packaged in shrink wrapped tray, giving you the added security of knowing that you have the right parts, prior to opening the package

from

$14.29

Tester adapter for the MT-300 cooling system pressure testers. Professional grade test equipment to ensure an automotive cooling system is operating at the correct pressure. Made from high quality materials to ensure durability. Designed to test automotive coolant caps.

Product Features:

Machined metal construction
Works with MT-300 pressure tester
Tests coolant caps
Professional quality

from

$172.99

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

Thermal tested under real-life temperature simulations
High tensile strength aluminum for maximum crimp strength
Plastic tanks are engineered with integrated ribbing for added strength to withstand cracks, bowing and distortion during thermal cycles
Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles
Oil cooler designs meet or exceed OE standards, keeping the vehicle’s engine and transmission performing at optimal conditions
OEM grade, premium fittings for transmission or engine oil coolers (where applicable)

from

$149.99

New Economy Replacement Radiator Support

Product Features:

Made Of Polypropelene & Glass fiber & steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$201.99

Carquest Premium water pumps are 100% new, high-quality parts that meet or exceed original equipment (O.E.) specifications. All components, including the housing, hub, bearings, gaskets and seals are designed for long-lasting service life. These water pumps are supplied with the gaskets or seals necessary for installation. Our Carquest Premium water pumps undergo stringent testing to ensure superior performance that we stand behind with an industry-leading warranty.

Product Features:

100% tested for reliable performance
Durable housing features precisely machined mounting surface for proper sealing and fitment
Equipped with weep chamber or similar feature to help prevent unnecessary replacement
Included heavy-duty unitized bearings, pressed-on hubs and optimal impeller clearance for a long-lasting water pump
All gaskets or seals necessary for water pump are included
This pump is driven by the accessory belt and we recommend replacement if nearing service recommendation