Name: Master Overhaul Kit for the Ford 9" LM102910 Differential, with Solid Spacer
Brand: USA Standard Gear
SKU: 37034
Price: 213.99 USD

from

$213.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Ford 9″ with LM102910 carrier race
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve eliminator, thread locker, marking compound with brush and gasket.

from

$8.38

Wheel Seal

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$4.99

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

from

$6.99

Ford 7.5″, 8″, 8.8″, & 9″ axle stud.

Product Features:

Axle stud for Ford 7.5″, 8.8″ and 9″
1/2″ x 20 thread
1 7/8″ long
29/64″ shoulder length

from

$128.59

Original equipment-specification hubs and bearings for Ford and Lincoln vehicles. Ford Parts hubs are micro-ground to help ensure the smoothest possible interface for nesting/mating with the rotor. Any runout wobble or imperfection on the rotor mounting surface of a hub, such as some found in the aftermarket, can be magnified by two times in the brake pad and cause premature wear and comebacks.

Product Features:

Testing, engineering and manufacturing tolerances held to 25 microns – three times thinner than a piece of paper – compared with some competitors at 250 microns
Optimized sealing effect and a low torque-to-turn ratio to minimize drag and help increase fuel economy
Special bearing seals to help keep out contaminants, the number one cause of bearing failure
Proprietary technology in the design and assembly process, where applicable, that is difficult to reverse engineer, helps ensure quality and helps reduce comebacks
Patented micro-grinding process, where applicable, that helps ensure the smoothest possible hub and rotor interface while helping to avoid premature brake wear and vibration
Helps avoid costly comebacks from pad, rotor or suspension parts problems that aftermarket replacement hubs may contribute to
Meets original equipment test specifications for each specific application Ford Parts hubs don’t compromise quality
Triple-sealed bearing assembly lubricated-for-life original equipment hub units provide excellent sealing performance
Integral bearing races specifically designed to each application, no one-size-fits-all solution
Precision forging Materials, engineering and production processes minimize any possibility of the hub cracking
Micro-ground hub-to-rotor mating surface – tolerances held below 25 microns to help prevent noise and vibration
Original equipment specifications minimize any possibility of the hub cracking
Original equipment ABS sensor ring and sensor pigtail feature high-strength polymer and copper wiring for positive connections and conductivity, providing excellent ABS signal
Tapered roller bearings for high load rates when specified

from

$623.99

RngPnn

from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$42.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.250″ O.D.
1.400″ I.D.

from

$41.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$10.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$84.99

7.5″ Ford notched cross pin shaft. Not Auburn gear. This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers.

Product Features:

Notched cross pin shaft for Ford 7.5″
3.73 and up ratios
Not compatible with Spartan Locker or Powertrax Lock Right

from

$44.99

SPICER U-JOINT

from

$12.34

Differential Pinion

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$10.99

Product Features:

Trac Loc spring plate for Ford 8″ and 9″

from

$99.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$74.99

Chrome cover for 8.8″ Ford.

Product Features:

Fits Ford 8.8″
Chrome

from

$14.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$286.99

Yukon flange yoke for 8.8″ Ford passenger and 8.8″ Ford IFS truck (4.3″ OD). All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″
30 spline
Round companion flange
4.3″ O.D.

from

$4.49

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$6.49

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$246.99

Yukon forged yoke for Ford 8.8″ with a 1350 U/joint size (stronger than billet). 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$17.99

Manufactured with premium-grade steel, National® taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$3.99

Trac Loc ring gear bolt washer for 8″ and 9″ Ford.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For Trac Loc positraction applications only

from

$96.99

2 piece solid spacer for Ford 8.8 and 7.5.

Product Features:

Crush sleeve eliminator kit for Ford 7.5″ and 8.8″

from

$579.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. This unit uses the factory side gears.

Product Features: