2007 Mitsubishi Eclipse Belts and Hoses
More 2007 Mitsubishi Eclipse Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2007 Mitsubishi Eclipse, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2007 Mitsubishi Eclipse Belts and Hoses
Dayco – Premium Balance Shaft Belt, 20.63 Inch With 55 Round Tooth (Part No.95159)
from
$18.29
Manufactured with tough, wear-resistant fabric, high-tensile strength cord and a molded tooth surface, the Dayco timing belt provides consistent slip-proof power transfer and high resistance to oil and engine heat. The belt features a molded cog design which runs quieter and is more economical and a premium, high modulus glass fiber cord that delivers precise length stability to keep the engine running smoothly over the life of the belt.
Product Features:
See More
Product Features:
- Designed for specific OHC and DOHC applications that range from normal service to high performance, high temperature engines
- Offers noise reduction and minimum dimensional tolerances for precise valve timing
- Engineered with reduced elongation for maximum durability, high abrasion resistance and better performance
- Belt tooth profile specifically designed to fit sprockets precisely and maintain timing effectiveness
Mitsuboshi – Mitsuboshi Balance Shaft Belt (Part No.A5002312117MBL)
from
$17.28
The Mitsuboshi Balance Shaft Belt is made to meet or exceed tough OE performance specifications and is resistant to high temperatures, is oil resistant and provides low noise and reliable operation.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application.
- Precision molded teeth.
- Resistant to abrasion and heat.
- Durable long life performance.
Dayco – Radiator Hose (Part No.G20001691131DAY)
from
$13.10
Radiator Hose
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 26" Long, 1.31" Diameter (Part No.E72109)
from
$26.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Heater Hose (Part No.18249)
from
$14.79
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 21 1/4 Inch Length (Part No.87792)
from
$33.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 90mm Dia., 31.2mm Width, Smooth (Part No.89138)
from
$35.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 84mm Dia., 25mm Width, Smooth (Part No.89134)
from
$40.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999216A)
from
$145.99
This Litens belt tensioner is supplied by the original equipment tensioner supplier and meets all form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). As with the original equipment part, this tensioner is manufactured in Japan for Mitsubishi’s 4G64 and 4G63 engines. This original equipment design maintains a lift feature for easy belt removal and replacement as well the O.E. specified steel pulley. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the original equipment part supplier to ensure proper form, fit and performance
- Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
- Installation instructions included.
- Durable Steel Pulley for long service life and performance.
- Professional Mechanics will change this tensioner in about 1 hour.
- Due to the fact that belts and tensioners have similar Original Equipment “design life targets”, it is often a best practice to replace the belt tensioner when replacing a worn or broken belt. Belt removal is required to change the tensioner. Therefore, d
Dorman – Timing Belt Adjuster (Adjuster only) (Part No.420-186)
from
$107.99
This belt tensioner damper is designed to match the fit and function of the damper on specified applications. Made of quality materials, it is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this belt tensioner damper is designed to match the fit and function of the damper on specified applications
- Restores functionality – reliable replacement for an original part that has failed due to fatigue or corrosion
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Gates – Micro-V« Serpentine Drive Belt (Part No.K040355)
from
$40.49
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.
Product Features:
See More
Product Features:
- Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
- EPDM rubber constructions resist cracking on the rib surface
- Meets or exceeds all specifications from the Original Equipment Manufacturer
- Tensioner Replacement is Recommended (if equipped)
- Unique form grinding of each individual belt assures precise dimensional control.
- Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
Dayco – Poly Rib Belt Serpentine Belt; 36.81 Long, 4 Rib Count (Part No.5040368)
from
$25.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter (Part No.900573A)
from
$62.99
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made to the O.E. specified design and meets all performance and durability requirements. This Heavy Duty Steel pulley is specifically designed for 2.0L/2.3L Mitsubishi car and SUV applications. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the largest original equipment part suppliers in the world to ensure proper form, fit, and performance
- Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance.
- Installation instructions included.
- 90mm O.D.; 10.1mm I.D; 30mm smooth running surface; heavy duty steel construction.
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter (Part No.900215A)
from
$85.99
This Litens pulley is manufactured by one of the largest original equipment suppliers in the world and meets all form, fit, and performance characteristics of the original equipment part . The Litens replacement part is constructed of heavy duty steel for long life and trouble free performance. NOTE: This pulley has been recently upgraded to a “pulley assembly” by including preassembled attachment hardware to improve ease of installation and performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the largest original equipment part suppliers to ensure proper form, fit, and performance
- Heavy Duty steel pulley with a long lasting automotive bearing.
- Precision steel stamping with close tolerance ball bearing pocket. Pre-assembled pulleys save installation time and ensure that all components are assembled to original specifications for both installation and performance
- Electro-deposited coating (e-coat) for superior corrosion resistance.
- Running surface designed and engineered for proper belt tracking.
- 97.6mm O.D.; 10.mm I.D (with bushing); 25.9mm width; smooth running surface; high-grade steel construction. For use with a 4- rib serpentine belt.
Gates – Premium Molded Coolant Hose (Part No.22906)
from
$28.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12" Long, 1.31" Diameter (Part No.B70815)
from
$17.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Mitsuboshi – Drive V-Belt (Part No.W100027691MBL)
from
$21.68
The Mitsuboshi Drive Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality.
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
Dayco – Bottom Cog V-Belt; 36.5 Inch Long, Exact Fit Premium Quality (Part No.17365)
from
$12.99
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Dayco – Dayco, Acc. Belt Idler Pulley (Part No.G60201330470DAY)
from
$88.07
The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application.
- Precision bearing
- OE High quality pulley assembly
- Durable long life performance.
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 76 mm Diameter (Part No.900200A)
from
$104.99
This pulley is manufactured by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Germany using the O.E. specified split steel pulley design and meets all performance and durability requirements. Comes with a new spacer and washer to ensure correct fit. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Gates – Premium Molded Coolant Hose (Part No.22981)
from
$32.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14" Long, 1.34" Diameter (Part No.D72592)
from
$18.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.21557)
from
$28.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 9/32 Inch Diameter, 5 Inch Length (Part No.86815)
from
$8.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.18030)
from
$16.79
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length (Part No.80402)
from
$23.49
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Popular 2007 Mitsubishi Eclipse Belts and Hoses Categories
2007 Mitsubishi Eclipse Belts and Hoses
You count on your 2007 Mitsubishi Eclipse to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 41 Belts and Hoses ranging in price from $1.79 to $145.99, you’re sure to find everything you need for your 2007 Mitsubishi Eclipse.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 7 different brands like Dayco, Driveworks, and Gates. 2007 Mitsubishi Eclipse Belts and Hoses start as low as $1.79!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 347 extensive product reviews on 2007 Mitsubishi Eclipse Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count with 5.0 stars and Serpentine Idler/Tensioner Pulley; Steel, 90mm Dia., 31.2mm Width, Smooth with 4.5 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2007 Mitsubishi Eclipse below to get started!
Top-Rated Belts and Hoses Brands For Your 2007 Mitsubishi Eclipse
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2007 Mitsubishi Eclipse running right for years to come. In our inventory you’ll find brands like Dayco, Driveworks, Gates, and even more.
Popular Litens Belts and Hoses
You’ll find popular Litens brand products across Pulleys. All are waiting to get your 2007 Mitsubishi Eclipse back on the road. Some of the top-rated Litens products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2007 Mitsubishi Eclipse, and some of our most reviewed Dayco parts include:
from
$33.99
(31)
Serpentine Idler/Tensioner Pulley; Steel, 82mm Dia., 27mm Width, Smooth
Idler Pulleys
from
$21.99
(8)
Flex Radiator Hoses; EPDM Rubber, 17.25 Inch Long, 1.25 Inch Inner Dia.
Coolant Hoses
FAQs for 2007 Mitsubishi Eclipse Belts and Hoses
What are the most purchased Belts and Hoses for the 2007 Mitsubishi Eclipse?
Out of 41 Belts and Hoses for the 2007 Mitsubishi Eclipse, the most popular in our inventory are:
from
$1.79
This product is not rated
Premium 5/16 X 50 Ft Heater Hose by Gates (sold by each)
Heater Hoses
from
$14.99
(8)
Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia.
By-Pass Hoses
What are the top-rated 2007 Mitsubishi Eclipse Belts and Hoses?
Top-rated Belts and Hoses for your 2007 Mitsubishi Eclipse based on customer reviews/ratings are:
from
$35.99
(4)
Serpentine Idler/Tensioner Pulley; Steel, 90mm Dia., 31.2mm Width, Smooth
“Advance auto always has top quality parts that i can always depend and this one was no different.”
from
$18.79
(3)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14" Long, 1.34" Diameter
“Store didn’t have an exact fit for a 2012 Elantra and I needed something right away. I just cut away about an inch on the straight end and it worked p”
