2007 Chevrolet C5500 Kodiak Drive Shafts and Axles
More 2007 Chevrolet C5500 Kodiak Drive Shafts and Axles
Find your specific 2007 Chevrolet C5500 Kodiak original or aftermarket Drive Shafts and Axles below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 2007 Chevrolet C5500 Kodiak Drive Shafts and Axles
Spicer – Universal Joint (Part No.5-178X)
from
$42.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More
Spicer – Universal Joint (Part No.5-1410X)
from
$51.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Spicer – SPICER U-JOINT (Part No.SPL70-4X)
from
$149.99
SPICER U-JOINT
Driveworks – Universal Joint (Part No.DW-331BL)
from
$31.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Spicer – Universal Joint (Part No.5-160X)
from
$40.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More
Spicer – Universal Joint (Part No.5-1350X)
from
$44.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Spicer – Center Support Bearing (Part No.210084-2X)
from
$69.99
Center Support Bearing
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6035)
from
$13.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 58-02; GMC 55-02; INTL 57-02;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2002
- Weight approx: 2 Lbs
- BEARING ID / BORE: 1.1811 INCH / 30 MM
- CENTERLINE: 3.50 INCH / 89 MM
- MOUNT WIDTH: 1.50 INCH / 38 MM
- COMPLETE MOUNT
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6048)
from
$46.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 81-88; CCC 87-13; CHEV 60-96; DODGE 71-81; FORD 75-98; GMC 79-96; INTL 57-02; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1957-2013
- Weight approx: 6 Lbs
- BEARING ID / BORE: 1.9685 INCH / 50 MM
- CENTERLINE: 2.80 INCH / 71 MM
- MOUNT WIDTH: 7.62 INCH / 194 MM
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)
from
$22.79
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.3780 INCH / 35 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- COMPLETE MOUNT
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)
from
$34.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 4 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.48 INCH / 63 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- NOT PICTURED: TWO DUST SHIELDS
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6040)
from
$17.79
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 81-88; CCC 87-13; CHEV 60-97; DODGE 78-81; FORD 75-98; GMC 79-97; INTL 57-02; KW 81-18; MACK 80-93; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1957-2018
- Weight approx: 4 Lbs
- BEARING ID / BORE: 1.7680 INCH / 45 MM
- CENTERLINE: 2.75 INCH / 70 MM
- MOUNT WIDTH: 7.62 INCH / 194 MM
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6049)
from
$37.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 81-88; CCC 87-13; CHEV 60-90; DODGE 78-81; FORD 75-98; GMC 79-90; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1957-2018
- Weight approx: 8 Lbs
- BEARING ID / BORE: 2.3622 INCH / 60 MM
- CENTERLINE: 3.37 INCH / 86 MM
- MOUNT WIDTH: 8.62 INCH / 219 MM
Spicer – Drive Shaft Center Support Bearing (Part No.210433-1X)
from
$88.99
The part you need. The name you trust. Spicer driveline components deliver top performance and value. These center bearing kits are manufactured to the same genuine standards you’ve come to expect from the most reliable name in driveshaft parts.
See More
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6027)
from
$5.29
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 87-97; GMC 67-05; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2012
- Weight approx: 1 Lbs
- CUSHION INSERT ONLY
- FOR COMPLETE MOUNT SEE PART 6056
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6053)
from
$39.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 60-02; DODGE 64-66; FORD 75-15; GMC 60-02;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1960-2015
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- NO STUDS
Popular 2007 Chevrolet C5500 Kodiak Drive Shafts and Axles Categories
2007 Chevrolet C5500 Kodiak Drive Shafts and Axles
Maybe you’re in the middle of a full rebuild of that 2007 Chevrolet C5500 Kodiak. Maybe you just need a couple of Drive Shafts and Axles. Either way, Advance Auto Parts has 7 different Drive Shafts and Axles in our inventory ranging from $31.99 to $204.99. That means you can find the exact parts or products you need to keep that 2007 Chevrolet C5500 Kodiak running smoothly.
Drive Shafts and Axles are only as good as their brand. We stock 2 different brands to make sure you have plenty of trusted parts to choose from for your 2007 Chevrolet C5500 Kodiak. Spicer and DriveWorks are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Drive Shafts and Axles for your 2007 Chevrolet C5500 Kodiak, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.
So if you’re in the market for aftermarket Drive Shafts and Axles to keep your 2007 Chevrolet C5500 Kodiak rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Drive Shafts and Axles Brands To Make Your 2007 Chevrolet C5500 Kodiak Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 2007 Chevrolet C5500 Kodiak demands trusted brand parts and products to keep it running. Many trusted brands of Drive Shafts and Axles make up Advance Auto Parts’ inventory, and all are ready to help make your C5500 Kodiak the best it can be. Be sure to browse some of our top Drive Shafts and Axles brands and parts.
Popular Driveworks Drive Shafts and Axles
We carry Driveworks parts in our stock across Axle Shaft Universal Joints categories, plus more. For a 2007 Chevrolet C5500 Kodiak, our most popular Driveworks Drive Shafts and Axles include:
Top 2007 Chevrolet C5500 Kodiak Drive Shafts and Axles from Spicer
Spicer products are another trusted brand when it comes to Drive Shafts and Axles for your 2007 Chevrolet C5500 Kodiak. Popular Spicer parts include:
FAQs for 2007 Chevrolet C5500 Kodiak Drive Shafts and Axles
What are the most purchased Drive Shafts and Axles for the 2007 Chevrolet C5500 Kodiak?
Out of 7 Drive Shafts and Axles for the 2007 Chevrolet C5500 Kodiak, the most popular in our inventory are:
