from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$12.99

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

Roll pin for Dana Spicer 30 and Dana Spicer 44
0.235″ diameter

from

$101.99

Product Features:

MINI SPOOL 8.8 FORD 31SPL

from

$649.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Ford 8.8″ with 31 spline axles and 7/8″ cross pin shaft
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$167.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2009 and down Ford 8.8″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 30

from

$8.49

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$4.99

Product Features:

Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

from

$5.99

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$13.99

Product Features:

O-ring for seal housing
Fits Dana Spicer 30 and AMC Model 35

from

$371.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$5.49

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$20.49

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit.

Product Features:

.047″ thick cellulose/nitrile composite gasket material
Precision die cut
Reusable

from

$19.60

Diff. Side Cover Sea

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$14.46

Diff. Bearing Shaft

from

$22.79

Product Features:

FORD 9″ SOLID SPACER KIT

from

$3.99

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

from

$386.99

Product Features:

Dura Grip positraction carrier case
Does not include spider gears
Fits Ford 8.8″ with 31 spline axles

from

$10.99

Dana 25, Dana 27, & Dana 30 side gear Thrust washer.

Product Features:

Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
1.560″ I.D.
Fits standard open differentials only

from

$169.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Spindle bearing and seal kit
Includes all components required to complete the repair
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$59.99

Product Features:

USA Standard Gear heavy-duty cross pin shaft
Fits Ford 8.8″ with 7/8″ cross pin diameter
Works with Spartan Locker or standard open spider gears

from

$155.99

Yukon replacement standard open spider gear kit for Dana 30 with 27 spline axles and with or without quick disconnect. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Dana Spicer 30 open differential with 27 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$16.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$14.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes