2003 Dodge Viper Fluids and Chemicals

Help keep positraction chatter down with posi additive from Yukon Gear & Axle.

Product Features:

• positraction additive
• For use in any clutch-style limited slip

3 oz. tube, carded – OEM specified. Specially formulated to withstand the harsh gear oil environment found in differentials and transfer cases. Because gear oil has friction modifiers that break down normal RTV and cause leaking, this specialty silicone has been tested to OEM specifications to ensure complete sealing. As a gasket maker, it seeks and seals leak paths that cut gaskets cannot. It can also be used to seal cut gaskets. Suggested Applications: Differentials and transfer cases. DIRECTIONS:

Product Features:

• For best results, clean and dry all surfaces with a residue-free solvent, such as Permatex® Brake and Parts Cleaner.
• Cut nozzle to desired bead size: gaskets are best formed using a 1/16? to 1/4? (2 to 6 mm) bead.
• Apply a continuous and even bead of silicone to one surface; surround all bolt holes. Assemble parts immediately. Finger tighten bolts until material begins to squeeze out around flange. Allow to dry for one hour then re-tighten 1/4 to 1/2 turn.
• Silicone dries in 1 hour, and fully cures in 24 hours. Allow more time in cold or very dry conditions.
• Replace cap after use. Note: Not recommended for use on head gaskets or parts in contact with gasoline. Store below 80°F (27°C). TECHNICAL DATA SHEET

PENTOSIN ATF 44 5L

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN

European engines need a premium motor oil designed to help them last. Valvoline European Vehicle Full Synthetic Motor Oil. It’s the motor oil specially developed to extend the life of European-made gasoline and diesel engines. Our exclusive formula uses top wear additives, premium antioxidants and added detergents to fight wear, resist oil breakdown and defend against deposits better than industry standards. Its exceptional range of temperature protection ensures your engine will be defended when the weather and road conditions get tough. This superior level of protection makes it the best choice for most Audi, BMW, Mercedes-Benz, Porsche, and VW vehicles. Engineered with ingenuity, tested with tenacity, and proven with purpose, our formula was innovated in America with a century and a half of hands-on experience from the original motor oil brand.

Product Features:

• Advanced protection in european vehicles agains the four main causes of engine breakdown: wear friction heat and deposits
• Extra wear protection vs. industry and oem standards with advanced anti-wear additives
• Superior performance for european gasoline and diesel engines
• Exceptional high/low temperature protection defends your engine no matter the climate or driving conditions
• Meets or exceeds all requirements of api sp, acea a3/b3, a3/b4, mb 229.5, 229.3, &226.5, vw 50200/50500 & 50501, bmw ll-01 & ll-14fe+, porche a40, volvo 95200356, renault rn0700 & rn0710, psa b71 2296, and chrysler ms-12633/ ms-10725
• Superior engine sludge and varnish protection for European-made gasoline and diesel engines.

Max Gear is recommended for truck and automotive differentials, outboard motor lower units or in rear axles or manual transmissions requiring an API fluid. Max Gear is a high performance automotive gear oil designed to provide maximum protection to heavily loaded gears while increasing power throughput through the drive train. Max Gear virtually eliminates both gear and bearing wear-even under severe squeeze film conditions caused by extremely high loads, sudden shock loads or low RPMs. Slippery, synthetic molecules not only reduce wear and friction but significantly increase Max Gear’s cold weather fluidity and lubricity, making it the ideal choice for vehicles operating in cold climates. Gears run smoother, quieter, cooler and longer without overhauls. It is noncorrosive to both ferrous and nonferrous metals.

Product Features:

• Maximizes horsepower
• Extends gear and bearing life
• Reduces operating temperature
• Lower coefficient of friction
• Superior corrosion protection
• Separates rapidly from water
• For use with open, limited-slip and locking differential
• Contains limited-slip friction modifier
• Made in USA

Prestone® DOT 4 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 4. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system. This formula is safe to use in all DOT 4 braking systems (ABS, disc or drum) and can mix with any DOT 4 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone® DOT 4 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 4. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system. This formula is safe to use in all DOT 4 braking systems (ABS, disc or drum) and can mix with any DOT 4 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone® MAX DOT 4 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 75,000 mile fluid life, our longest life fluid has 1.5X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 4, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 4 is safe to use in all DOT 4 braking systems, ABS, disc or drum, and can mix with any DOT 4 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 4. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 75,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 1.5X Longer than regular Prestone DOT 4

FRAM Extended Life AMAM 50/50 is compatible with ANY antifreeze/coolant in ANY vehicle with aluminum or other cooling system metals. The formulas have a blend of long-lasting inhibitors to guard against temperature extremes and the effects of rust, corrosion, and premature water pump failure. Top-off your cooling system with FRAM Extended Life AMAM 50/50, which is a blend of 50% antifreeze and 50% demineralized water. FRAM 50/50 meets or exceeds ASTM D3306 and D4985 for corrosion protection for cars and light duty trucks, while providing reliable freeze-up & boil-over protection.

Product Features:

• Formulated to work with All Vehicles. Universally works with all fluid colors; All OAT, POAT, HOAT & IAT.
• 5 Yr., 150,000 mile Extended life formula.
• Meets or exceeds ASTM D3306 & D4985 for corrosion protection.
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Prestone DEX-COOL (Ready to use) antifreeze+coolant is specially designed to work with these specific vehicles: All GM® vehicles 1995 & newer (GM approved), most Ford® vehicles 2011 – 2018 and most Chysler® vehicles 2013 & newer. Prestone’s Antifreeze+Coolants are designed to the highest standards using state of the art technology. These fluids are designed to not only manage the engine temp and protect from freezing up, they also protect the engine from rust & corrosion. This fluid is designed to last 5yrs / 150,000 miles.

Product Features:

• Specially formulated to work with vehicles using orange colored fluid; HOAT. All GM 1995 & newer; Most Ford 2011-2018; Most Chrysler 2013 & newer
• 5 Yr., 150,000 mile Extended life formula
• Includes the Prestone protection package that protects against rust and corrosion of all cooling system metals, including aluminum.
• Ready to Use formula. Perfect for small volume top-off or complete drain and refill of the cooling system.

FRAM Orange 50/50 is formulated for cars and light duty trucks that use Orange extended life coolant. Top-off your cooling system with FRAM Orange 50/50, which is a blend of 50% antifreeze and 50% demineralized water. FRAM Orange 50/50 meets or exceeds ASTM D3306 and D4985 standards for corrosion protection, while providing reliable freeze-up and boil-over protection.

Product Features:

• Work with vehicles using orange colored fluid. 5 Yr., 150,000 mile Extended life formula.
• All GM« vehicles 1995 & newer /GM approved (GMC, Chevrolet, Buick, Cadillac, Pontiac, Saturn, Oldsmobile, Hummer), most Ford« vehicles 2011- 2018 (Ford, Lincoln, Mercury) and most Chrysler« vehicles 2013 & newer (Ram, Dodge, Jeep, Chrysler)
• All GM® vehicles 1995 & newer /GM approved (GMC, Chevrolet, Buick, Cadillac, Pontiac, Saturn, Oldsmobile, Hummer), most Ford® vehicles 2011- 2018 (Ford, Lincoln, Mercury) and most Chrysler® vehicles 2013 & newer (Ram, Dodge, Jeep, Chrysler)
• Meets or exceeds ASTM D3306 & D4985 for corrosion protection.
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Prestone DEX-COOL (concentrate) antifreeze+coolant is specially designed to work with these specific vehicles: All GM® vehicles 1995 & newer (GM approved), most Ford® vehicles 2011 – 2018 and most Chysler® vehicles 2013 & newer. Prestone’s Antifreeze+Coolants are designed to the highest standards using state of the art technology. These fluids are designed to not only manage the engine temp and protect from freezing up, they also protect the engine from rust & corrosion. This fluid is designed to last 5yrs / 150,000 miles.

Product Features:

• Specially formulated to work with vehicles using orange colored fluid; HOAT. All GM 1995 & newer; Most Ford 2011-2018; Most Chrysler 2013 & newer
• 5 Yr., 150,000 mile Extended life formula
• Includes the Prestone protection package that protects against rust and corrosion of all cooling system metals, including aluminum.
• Concentrate formula. Must mix with distilled to the desired mix ratio of EG & water. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

Pennzoil Platinum full synthetic SAE 5W-30 motor oil is uniquely engineered from our revolutionary PurePlus gas-to-liquid technology, which is a patented process that converts pure natural gas into a high quality, full synthetic base oil. Our high quality base oil is 99.5% pure, contains fewer impurities than base oils made from crude oil, and when combined with our advanced additive technology creates one of the best formulations in our Pennzoil portfolio. Pennzoil Platinum full synthetic SAE 5W-30 motor oil is licensed and meets the vehicle warranty requirements of GM’s dexos 1 Gen 2 specifications that are set forth to meet today’s modern engine technologies. This means that our Pennzoil Platinum full synthetic products meet the stringent requirements of leading car manufacturers. Why does this matter? Modern engine technologies have evolved over the years and today’s engine parts have reached an unprecedented level of fine manufacturing tolerances which require a high-quality engine oil to help provide complete engine protection. This includes protection against abnormal combustion phenomenon like low-speed pre-ignition observed in modern turbocharged gasoline direct injection (TGDI) engines. Our Pennzoil Full Synthetic products are engineered for modern engines and offer the following benefits without compromise. Better Fuel Economy. With Pennzoil Platinum full synthetic motor oil, you can drive on average an extra 550 miles vs a dirty engine. Protects Horsepower. Pennzoil Platinum Full Synthetic motor oil helps protect against loss of power by helping to protect your engine against wear and deposit formation. Unsurpassed Wear Protection. When it comes to protecting the internal parts of your engine from metal-on-metal contact, no other leading synthetic motor oil provides better wear protection than Pennzoil Platinum Full Synthetic motor oil. Excellent Temperature Performance.

Product Features:

• Provides better fuel economy-drive on average an extra 550 miles per year (versus a dirty engine)
• Pennzoil Platinum 0W-20 keeps pistons up to 45% cleaner than the toughest industry standard (Based on Sequence IIIH results)
• No other leading synthetic oil provides better wear protection from friction (Based on Sequence IVA wear test using SAE 5W-30)
• Formulated to provide faster low-temperature oil flow and protection in extreme heat
• Helps protect engines from loss of power
• Formulated for modern turbocharged engines-GF-6, API SP/SP-Resource Conserving and all previous categories
• Revolutionary PurePlus Technology: Engineered from Pennzoil’s patented PurePlus gas-to-liquid technology, converting pure natural gas into high-quality, full synthetic base oil that is 99.5% pure.
• Superior Engine Protection: Provides unsurpassed wear protection, safeguarding internal engine parts from metal-on-metal contact better than other leading synthetic motor oils.
• Meets Modern Engine Requirements: Licensed and meets GM’s dexos 1 Gen 2 specifications, ensuring compatibility with today’s advanced engine technologies and stringent car manufacturer requirements.

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

• FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

Quaker State Full Synthetic Motor Oil SAE 5W-30 contains the most powerful formulation in the Quaker State portfolio. This product offers superior resistance to thermal and viscosity breakdown compared to Quaker State Synthetic Blend Motor Oil. As the engine temperature increases, the heat activated shear stable viscosity modifiers work to maintain oil film thickness that is necessary to prevent engine parts from metal on metal contact which helps extend engine life. This motor oil maintains its viscosity from start to finish, which means it stays in the grade specified by the car manufacturer throughout the recommended oil drain interval. The product also contains special detergents and dispersant additives that are designed to neutralize the harmful acids generated by the combustion process. This helps prevent the formation of sludge and deposits from forming on crucial engine parts. These properties of Quaker State Ultimate Durability full synthetic motor oil make it reliable and suitable for use in high performance vehicles such as sport cars, SUVs, trucks and minivans. It is compatible with biofuels, ranging from E10 to E85 and suitable for hybrid vehicles.

Product Features:

• Quaker State Ultimate Durability is our most powerful formulation, providing extreme engine performance and protection against deposits, which allows your engine to operate at maximum horsepower
• No leading synthetic motor oil provides better protection from friction-related wear when compared to industry standard Sequence IVA engine test results
• Helps protect against the effects of low-speed pre-ignition (LSPI) in modern turbocharged engines.
• Provides excellent protection against the formation of sludge and other harmful deposits when compared to Quaker State Synthetic Blend Motor Oil
• Superior lubrication flow and pumpability at high and low temperatures when compared to Quaker State Synthetic Blend Motor Oil

Today’s advanced engine technology requires advanced protection. Valvoline Advanced Full Synthetic, the motor oil designed to protect today’s sophisticated engines, contains premium anti-wear additives, superior antioxidants and extra detergents. It protects 40% better against wear, resists oil breakdown 10-times better, and defends 25% more against deposits than industry standards for maximum performance and engine longevity. And with an exceptional range of temperature protection your engine will ready for extreme weather. Valvoline invented motor oil 150 years ago, and we’ve been reinventing it ever since. Get Valvoline Advanced Full Synthetic and give your engine the advanced protection proven to maximize engine life.

Product Features:

• ADVANCED PROTECTION AGAINST the four main causes of engine breakdown: wear friction heat and deposits
• 40% BETTER WEAR PROTECTION vs. industry standard as tested in the Sequence IVB engine test
• 25% BETTER DEPOSIT PROTECTION with superior engine cleaning detergents as tested in the GMOD engine test
• EXCEPTIONAL HIGH/LOW TEMPERATURE PROTECTION defends your motor no matter the weather conditions
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN, GM dexos 1 Gen 3
• Enhanced Oil Stability: Resists oil breakdown 10-times better than industry standards, providing consistent performance and reliability.
• Premium Additives: Contains premium anti-wear additives, superior antioxidants, and extra detergents for maximum performance and engine longevity.

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Prestone® Power Steering Fluid (PSF) delivers increased system life. Designed with Anti-wear System Protection, Prestone PSF protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• For use in all manufacturers
• Conventional Formula – For use in all manufacturers

Prestone® MAX American Vehicles Power Steering Fluid (PSF) + Stop Leak maximizes and increases system life + the power to stop leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. This formula is also great at preventing leaks by rejuvenating seals before they leak. This synthetic fluid is designed with 2X Anti-wear System Protection, which means more protection against pump failure, squeals and clogs. 100,000 mile fluid life, 2X more than conventional fluid, extends the time between replacement. This fluid is formulated for American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and others. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 100,000 Mile Fluid Life. Synthetic Formula for longer life and more protection
• MAX + Stop Leak. Stop Leak Additives to prevent and stop power steering system leaks.
• For use in American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and other
• 2X Anti-Wear Protection for enhanced System Life vs. conventional fluid. More protection against pump failure, squeals and clogs

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

• Limited 12 Month Or 12,000 Mile Warranty