from

$1145.00

Differential

from

$502.99

Dana 80 TracLoc clutch set round design (remove 4 plates 4 V-Type).

Product Features:

Clutch kit
Fit Dana Spicer 80 Trac Loc positraction

from

$1060.00

Yukon Performance steel spool for 8Dana 80 with 37 spline axles, 4.10 & up. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler Dana Spicer 80 with 37 spline axles
4.10 and up ratio only
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$319.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$197.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

BEARING & SEAL KT DANA 80

from

$138.99

S135 ring gear bolt & nut kit (set of 16 bolts).

Product Features:

Ring gear bolt and nut kit
Fits Dana Spicer S135
Includes 12 bolts and nuts

from

$209.99

Extra large clamshells for use with Dana 70HD, Dana 80, AAM 11.5″, Ford 9.75″, Ford 10.25″ & Ford 10.5″.

Product Features:

Extra Large clamshell
Fits carrier bearing puller

from

$42.99

Pinion nut for Spicer S135 & S150.

Product Features:

Pinion nut
Fits Dana Spicer S135 and S150

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$215.99

Bearing race drive for Ford 10.25″ and 10.5 axle bearing. (TK 3920). No return.

Product Features:

Bearing race driver
Fits 3920 race
All steel construction

from

$14.49

Product Features:

Brand may vary by location

from

$872.99

Yukon replacement standard open spider gear kit for Dana S135 with 36 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Dana Spicer S135 open differential
Includes two side gears, two four gears, cross pin shaft and spider gear thrust washers.

from

$4.99

Product Features:

Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
Fits standard open differentials only

from

$172.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$554.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Dana Spicer 80
11.25″ ring gear diameter
37 spline pinion
12 ring gear bolts
3.54 ratio

from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$446.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers, thread locker, marking compound with brush and silicone.