from

$1645.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$299.99

Yukon standard open spider gear kit for 8.8″ Ford with 31 spline axles and 7/8″ pin. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 8.8″ with 31 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
0.875″ cross pin shaft diameter

from

$451.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$51.99

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

Carrier race
Fits Ford 9″
Conversion race to install small bearing carrier into 3.250″ dropout

from

$41.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$29.99

20 long air line for Zip Locker.

Product Features:

Air line
20′ in length

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$8.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$64.99

Spectre’s Differential Covers are made to OEM specifications and are triple chrome plated for a lasting shine. Designed to protect the intricate moving parts of the differential, Spectre’s covers add an extra layer of protection to the vehicle’s underside. Featuring a 10-bolt design and fits the following vehicles with 8.8 inch ring gears: 1986-2003 Ford Mustang/Capri V8, 1983-2003 Ford F150/Bronco two or four wheel drive, 1991-2003 Ford Explorer two or four wheel drive, 1983-1998 Ford E150/250, and 1994-2003 Mazda 4000 differentials. Includes 10 SAE standard chrome bolts for installation. You’ll need to supply your own bolts if your application requires metric bolts.

Product Features:

Includes bolts and a gasket
10-bolt design
Triple chrome plated for a lasting shine
10 chrome 5/16 inch -18 x 3/4 inch differential cover bolts included

from

$78.99

Seal housing for Ford 10.25″ & 10.5″, Zip locker, with o-rings.

Product Features:

Seal housing for Ford 10.25″ and 10.5″
Includes o-rings

from

$249.99

9.75″ TracLoc clutch set, 16 Pieces (does not include belleville).

Product Features:

Clutch kit
Fit Ford 9.75″ Trac Loc positraction

from

$6.99

Product Features:

Oil baffle for Dana Spicer 44

from

$221.99

Yukon 1541H replacement inner axle for Dana 44 IFS with a length of 24.77 inches and with 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy front axles come with a one year warranty against manufacturing defects.

Product Features:

30 spline
24.77″ long
Fits Dana Spicer 44 IFS in 1980-1996 Ford F150
Right hand inner
5-760X U-joint size

from

$52.99

Cross pin shaft (0.875″) for ’86 and newer 8.8″ Ford.

Product Features:

Cross pin shaft for Ford 8.8″
0.875″ diameter

from

$259.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9″ with Daytona pinion support
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$53.99

Front axle inner seal REDI-sleeve for Dana 30 1.192″ shaft..Yukon Mighty seal.

Product Features:

Pinion seal
Fits 2011 and up Ford 10.5″

from

$213.99

Yukon long yoke for ’93 and newer Ford 10.25″ with a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 1993 and up Ford 10.25″
31 spline
1310 u-joint size
Outside snap ring design
3.625″ snap ring span
1.125″ cap diameter
U-bolt style

from

$5.49

Product Features:

F9.75″ RING GEAR BOLT SOLD INDIVIDUALLY

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits HM88610 race
All steel construction

from

$23.99

Pinion gear for 8″ and 9″ Ford.

Product Features:

Pinion gear
Fits Ford 8″ and 9″

from

$51.99

Product Features:

Complete shim kit for Dana Spicer 44

from

$276.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 10.25″ & 10.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 10.25″ and 10.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$2.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$18.58

Axle Housing Cover G

from

$14.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$10.99

Product Features:

Trac Loc spring plate for Ford 8″ and 9″

from

$10.99

Yukon 1541H alloy rear axle for ’88-’97 GM 7.5″ S10 2WD (non-ABS) with a length of 26-7/8 inches and 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year war

Product Features: