2002 Ford E-350 Super Duty Drivetrains
More 2002 Ford E-350 Super Duty Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 2002 Ford E-350 Super Duty, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 2002 Ford E-350 Super Duty Drivetrains
Yukon Gear – Minor Install Kit For Dana 70-U Differential (Part No.12029)
from
$141.99
Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.
Product Features:
See More
Product Features:
- Fits Dana Spicer 70U
- Included are a pinion seal, complete shim kit, marking compound and brush.
Pro-King – Differential Rebuild Kit (Part No.718B004)
from
$381.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket. All products are designed to meet or exceed OE quality, form, fit and funtion.
Product Features:
See More
Product Features:
- Contains the highest quality Japanese bearings
Yukon Gear – Axle O-Ring For Ford 10.25" & 10.5" (Part No.33465)
Yukon Gear – Chrysler 9.25" And Dana 44 / 60 Tracloc Clutch Guide Replacement (Part No.33249)
from
$8.99
Product Features:
See More
- Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
- For Trac Loc positraction applications only
Yukon Gear – Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (Part No.33164)
from
$3.99
Product Features:
See More
- Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″
Yukon Gear – AxleHubBolt (Part No.33587)
from
$7.99
AxleHubBolt
Yukon Gear – Side Gear Thrust Washer For Dana 60, 70 & 80 (Part No.33532)
from
$4.99
Product Features:
See More
- Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
- Fits standard open differentials only
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1350 U/Joint Size (Part No.41026)
from
$179.99
Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1350 u-joint size
- 3.625″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)
from
$37.99
Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.
Product Features:
See More
Product Features:
- Redi-Sleeve yoke saver
- Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD
Yukon Gear – Spindle Nut Retainer For Dana 60 & 70, 1.830" I.D., 10 Outer TABS (Part No.33477)
from
$10.99
Spindle nut retainer for Dana 60 & 70, 1.830″ I.D., 10 outer tabs. This replaces Spicer part number 30637.
Product Features:
See More
Product Features:
- Spindle nut retainer for Dana Spicer 60, 70, 70U and 70HD
- 1.830″ I.D.
- 10 outer tabs
Dorman – Rear Axle Shaft, Right (Part No.630-243)
from
$479.99
Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.
Product Features:
See More
Product Features:
- Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
- Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
- Durable construction – designed to rigorous standards and tested to ensure performance
- Trustworthy solution – backed by team of engineers and quality control specialists in the United States
Motive Gear – Differential Gear Install Kit (Part No.D80IK)
Driveworks – Taper Bearing Cup (Part No.S-15245)
from
$5.99
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
USA Standard Gear – Steel Spool For Dana 60 With 35 Spline Axles, 4.56 & Up (Part No.59018)
from
$369.99
Product Features:
See More
- Fits Chrysler Dana Spicer 60 with 35 spline axles
- 4.56 and up ratio only
- Provides 100% traction to both wheels at all times
- Not recommended for street driven vehicles
Dorman – Spindle Nut (Part No.K1002831714DOR)
from
$42.79
Spindle Nut
National – Multi Purpose Bearing (Part No.HB-88508-A)
from
$73.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)
Yukon Gear – Dana 60 Semi-Float C-Clip (Part No.33247)
Yukon Gear – Replacement Inner Slinger For Dana 60 (Part No.33014)
Yukon Gear – The Carrier Bearing Puller (Part No.56072)
from
$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)
from
$34.99
1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.
Product Features:
See More
Product Features:
- u-joint u-bolt kit
- Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
- 1310 u-joint size
- Includes two u-bolts and four nuts
Yukon Gear – Replacement Trac Loc Carrier Case, Dana 60, 4.10 & Down (Part No.20043)
from
$509.99
Product Features:
See More
- Trac Loc positraction carrier case
- Does not include spider gears
- Fits Dana Spicer 60
- 4.10 and down ratio only
- ABS and non-ABS compatible
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)
from
$34.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 4 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.48 INCH / 63 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- NOT PICTURED: TWO DUST SHIELDS
Yukon Gear – Zip Locker Bulkhead Fitting (Part No.34001)
Yukon Gear – Dana 60 & Dana 61 Tracloc Clutch Set (Part No.16156)
from
$269.99
Dana 60 & Dana 61 TracLoc clutch set.
Product Features:
See More
Product Features:
- Clutch kit
- Fit Dana Spicer 60 Trac Loc positraction
Dorman – Help – Driveshaft Flange Bolts (Part No.80992)
from
$20.29
This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Yukon Gear – Ppinion Nut 7/8-20 Thread, 1 1/8 Socket (Part No.33146)
from
$10.99
Replacement pinion nut for Model 20 & 35, Dana 30 JK, 44 JK front, Ford 10.25″, 10.5″ & some 9.75″. 7/8-20 thread, 1 1/8 socket.
Product Features:
See More
Product Features:
- Pinion nut for Jeep JK front, Jeep Liberty front, Ford 9.75″, 10.25″, 10.5″ and AMC Model 20 and Model 35
- 7/8″ x 20 thread
- 1 1/8″ socket
Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41022)
from
$233.99
Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 and 70
- 29 spline
- 1310 u-joint size
- Outside snap ring design
- 3.219″ snap ring span
- 1.062″ cap diameter
- Strap style
Popular 2002 Ford E-350 Super Duty Drivetrains Categories
2002 Ford E-350 Super Duty Drivetrains
You count on your 2002 Ford E-350 Super Duty to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 385 Drivetrains ranging in price from $2.99 to $1,487.99, you’re sure to find everything you need for your 2002 Ford E-350 Super Duty.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 18 different brands like Valvoline, Moog, and National. 2002 Ford E-350 Super Duty Drivetrains start as low as $2.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 2,501 extensive product reviews on 2002 Ford E-350 Super Duty Drivetrains. Some of the top-rated Drivetrains products we carry are Multi Purpose Bearing with 3.4 stars and Wheel Bearing: Direct Fit, 1 Piece with 4.4 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 2002 Ford E-350 Super Duty below to get started!
Top-Rated Drivetrains Brands For Your 2002 Ford E-350 Super Duty
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2002 Ford E-350 Super Duty running right for years to come. In our inventory you’ll find brands like Valvoline, Moog, National, and even more.
Popular Dorman Drivetrains
You’ll find popular Dorman brand products across Spindles and Drive Shafts and Axles. All are waiting to get your 2002 Ford E-350 Super Duty back on the road. Some of the top-rated Dorman products in these categories are:
Top-Rated Valvoline Drivetrains
If Valvoline are what you’re looking for, our inventory holds plenty. We stock Valvoline brand Drivetrains for your 2002 Ford E-350 Super Duty, and some of our most reviewed Valvoline parts include:
from
$12.79
(446)
MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart
Differential Oil
FAQs for 2002 Ford E-350 Super Duty Drivetrains
What are the most purchased Drivetrains for the 2002 Ford E-350 Super Duty?
Out of 385 Drivetrains for the 2002 Ford E-350 Super Duty, the most popular in our inventory are:
What are the top-rated 2002 Ford E-350 Super Duty Drivetrains?
Top-rated Drivetrains for your 2002 Ford E-350 Super Duty based on customer reviews/ratings are:
