2002 Chevrolet Camaro Performance Engines

This Holeshot 2000 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1997 4L60E w/30 spline input, and 1997-04 Corvettes. This converter retains the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace-brazed impeller fins and turbine, a new precision alloy impeller hub, and new heavy-duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate-type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, and less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide, or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

The Tork Master 2400 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1996 4L60E w/30 spline input transmissions. This converter retains the lock-up feature. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75 in. bolt circle

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing drivability and creature comforts, the Xtreme Energy grind family offers gains in torque and horsepower while still delivering adequate vacuum for power brakes and other vacuum dependent accessories. Xtreme Energy camshafts work great in carbureted applications, but offer the best performance with aftermarket intake manifolds, lower gear ratios, headers and free flowing exhaust.

“Edelbrock part No: 5487 Performer-Plus camshaft is designed for Buick 321-252 Even Fire V-6 applications. The camshaft will produce optimum torque from the low-end to the mid-range, Performer-Plus camshafts match with Performer manifolds for vehicles operating from off-idle to 5500 rpm. This Performer-Plus is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. All camshafts include flat tappet lifters, assembly lube and instructions. Camshaft Specifications: – Duration at .050 Intake: 204 degrees – Duration at .050 Exhaust: 214 degrees – Lift at Valve Intake: .448″” – Lift at Valve Exhaust: .472″” – Lobe Separation: 112 Degrees – Intake Centerline: 107 Degrees – Idle Vacuum at 1000 RPM’s: 15″””

Edelbrock Valve Spring Retainers are made of superior quality steel and are machined and heat treated for maximum strength. They feature a black oxide finish to prevent rust and corrosion

“Competition Cams Tool Steel 10 Degree Retainer For All Valves With 1.250″” O.D. Springs, 1750-1. ”

“CNC-machined for consistency, this 7 degree tool steel retainer features light weight, exceptional strength and wear characteristics. Fits 8mm valve engines with a 1.290″” O.D. spring such as our 26926 springs.”

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Edelbrock part #2104 Performer intake manifold is designed for street 262-400 c.i.d. Chevy V8’s that have heads with canted center bolt holes, 1987-1995. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response. The Performer intake manifolds are ideal for passenger cars, trucks, 4x4s, tow vehicles and RVs. For 1987-95 stock aluminum heads use #2101.

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Weiand Stealth Ram Intake Manifold, 7540.

Holley Intake Manifolds feature a cast aluminum construction and have a long tradition of being one of the best products on the market. Review the information below for Holley intake specifications.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

The Edelbrock No: 7380 head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit and sealing properties when used with Edelbrock aluminum cylinder heads. Edelbrock head gaskets are manufactured from high-density materials and feature a superior design that performs under pressure and provides a long-lasting seal, without re-torqueing.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermo conductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually. Gasket bore 4.100 inch, Compressed thickness 0.028 inch

Competition Cams Camshaft Lock Plate w/ Bolts for GM LS GEN III/IV with 3 Bolt Camshaft, 5461.

“This Beehive Valve Spring Kit for LS engines is designed for hydraulic roller cams and includes carefully matched Beehive Springs, steel retainers, locks, seals and spring seats. With a .625″” maximum lift, these Beehive Valve Springs deliver increased valve train stability and a much lighter valve train. This is achieved with less spring pressure for better valve control and reduced weight of both the spring and retainer. The unique Beehive shape handles valve train stress more efficiently to eliminate damaging harmonics and increases high RPM horsepower and durability. The oval/multi-arc wire shape places the maximum area of the wire at the point of highest stress to handle valve train stress more efficiently and allow better heat dissipation for longer life.Kit Includes:26918-16 Beehive Valve Springs774-16 Steel Retainers623-16 7° Steel Valve Locks511-16 Valve Seals4705-16 Spring Seats”

“Competition Cams Valve Spring Kit, For Ls 1.310″” Beehive 1 Kt, 26915CS-KIT. ”

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

“With a .625″” maximum lift, these Beehive Valve Springs were designed for hydraulic roller cams in LS1, LS2 and LS6 engines. COMP Cams Beehive Valve Springs deliver increased valve train stability and a much lighter valve train. This is achieved with less spring pressure for better valve control and reduced weight of both the spring and retainer. The unique Beehive shape handles valve train stress more efficiently to eliminate damaging harmonics and increases high RPM horsepower and durability. The oval/multi-arc wire shape places the maximum area of the wire at the point of highest stress to handle valve train stress more efficiently and allow better heat dissipation for longer life. Because of the unique Beehive design, the valve train can handle more RPM and more aggressive cam profiles.”