2001 Ford F-150 Drivetrains

Below you will find various in-demand Ford Drivetrains, components and accessories for your 2001 F-150. Advance Auto Parts has popular F-150 parts like 4WD Components, Transfer Cases, Drive Shafts and Axles and more. You’ll also find aftermarket and OEM Drivetrains for other F-150 model years including 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023 and more. Select a category of 2001 Ford F-150 Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 2001 Ford F-150 Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

4WD Actuator Switches

4WD Axle Actuator Housings

Differential Pinion Yokes

Drive Shaft Support Bolts

U-Joints

Drive Shaft and Axles

Transfer Case Assemblies

Transmission Transfer Case Motors

Transfer Case Adapter Gaskets

Transfer Case Gaskets

Rear Differential Cover Gaskets

Transfer Case Control Levers

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Axle Shafts

Bearing Pullers

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

OE CV Boot Kits

Differential Pinion Pilot Bearings

Locking Hub Service Kits

4WD Switches

Differential Cover Bolts

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Axle Hub O-Rings

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Axle Spindle Bearings

Differential Disc Kits

Axle Vents

Differential Clutch Packs

Rear Axle Shaft Bearings

Differential Mini Spools

Differential Ring and Pinions

U-Joint U-Bolt Kits

Differential End Yokes

Spindle Lock Nuts

4WD Actuator Forks

Drive Shaft Repair Kits

Differential Lock Assemblies

Differential Air System Seal Housings

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Differential Lock Springs

Rear Housing Cover Gaskets

Axle Support Bushings

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Complete Differentials

Bearing and Seal Overhaul Kits

Differential Ring Gear Bolts

Bearing Race Drivers

Differential Pinion Shafts

Differential Carrier Bearing Shims

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Pinion Shaft Seals

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Axle Shaft Studs

Differential Drive Pinion Oil Deflectors

Spindle Washers

Axle Shaft Bolts

Differential Ring and Pinion Kits

Drive Axle Assemblies

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

4WD Actuator Connectors

Axle Shaft O-Rings

Differential Pinion Gear Nut

Essential Drivetrains for 2001 Ford F-150s

from

$1997.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$10.29

Formulated to meet the specific requirements of Subaru vehicles equipped with conventional (non-CVT) transmissions up to model year 2005. Recommended for service-fill in all Subaru automatic transmissions where SUBARU ATF HP is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. Idemitsu is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. Idemitsu application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings

from

$5.99

Product Features:

Rear axle stud for Dana Spicer 44 and AMC Model 35
1/2″ x 20 thread
0.618″ knurl diameter
1 15/32″ long
31/64″ shoulder length

from

$11.99

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications
Effective fix – restores a tight seal in the transfer case after original gasket fails
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$475.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$7.99

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

Pinion nut for Ford 7.5″, 8″ and 9″
3/4″ x 20 thread
1 1/6″ socket

from

$52.99

Air line repair kit, ZIP locker.

Product Features:

Air line repair kit
Includes 20′ air line and two repair fittings

from

$24.99

Spindle nut for Dana 30 & Dana 44, .372″ thick. This replaces Spicer part number 21588X.

Product Features:

Spindle nut for Dana Spicer 30 and 44
0.372″ thick

from

$144.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$25.99

Left inner axle replacement seal for Dana 44, 50, Model 35 IFS.Yukon Mighty seal.

Product Features:

Inner axle seal
Left hand side
Fits Dana Spicer 44 IFS, AMC Model 35 IFS and Dana Spicer 50 IFS

from

$189.99

Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:

Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications
Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion
100% new – this transfer case motor is entirely new, not remanufactured like competitors
Quality assured – vehicle-specific application has been validation tested to ensure quality

from

$12.49

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$10.99

Yukon 1541H alloy rear axle for ’88-’97 GM 7.5″ S10 2WD (non-ABS) with a length of 26-7/8 inches and 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year war

Product Features:

Outer slinger
Fits 2011 and up Ford 10.5″

from

$9.99

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
0.480″ tall

from

$8.99

Product Features:

Axle o-ring
Fits Ford 10.25″ and 10.5″

from

$34.99

This CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$4.79

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles
Quality materials – all components are built for reliable longevity and performance
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$185.99

Product Features:

DANA-44 R/P 4.56 STD MG

from

$12.99

DrvShftPinYoke

from

$27.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$45.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$13.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$43.99

The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. they are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.

Product Features:

Forged From Premium Grade 8740 Chrome Moly Steel
Heat Treated
Nominally Rated At 200,000 Psi Tensile Strength
Specially Hardened, Precision Ground Washers
0.75″ Underhead Length
200,000 PSI
Sold As A Set

from

$40.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$74.99

Differential Side Be

from

$215.99

Bearing race drive for Ford 10.25″ and 10.5 axle bearing. (TK 3920). No return.

Product Features:

Bearing race driver
Fits 3920 race
All steel construction

Upgrade your 2001 Ford F-150 with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 2001 Ford F-150, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your F-150 functioning at its best. At Advance Auto Parts, we offer a wide selection of 563 Drivetrains for the 2001 Ford F-150, designed to meet your needs without breaking the bank. From 4WD Component replacements to Transfer Cases upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 2001 Ford F-150 at great prices. Our Drivetrains inventory for this model ranges from just $1.29 to $3,089.99, with an average price of $329.53. Our 563 Drivetrains in stock come from 27 trusted brands, so you’re sure to find the right part for your 2001 Ford F-150 without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2001 Ford F-150, we stock popular OEM and aftermarket Drivetrains from top names like National, Dorman, Motive Gear, and more. National Drivetrains start at just $7.99 and boast an impressive 4.3 stars average rating from customers. Dorman and Motive Gear also bring quality to the table, with Drivetrains available starting at $7.99, and at an average 4.2 stars rating. With 24,823 customer reviews and counting, our 2001 Ford F-150 Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2001 Ford F-150 is always ready to roll. We’re committed to providing you with everything you need to keep your F-150 in top shape, all in one place. Start shopping confidently below for your 2001 Ford F-150!

Best-Selling 4WD Components for 2001 Ford F-150s

Enhance the driving experience in your Ford with 8 quality 4WD Component components, starting at $39.99.

show more show less

from

$53.99

This 4WD hub locking solenoid directly replaces the original equipment solenoid on certain vehicle years, makes and models.

Product Features:

Direct replacement – this 4WD hub locking solenoid matches the fit and function of the stock solenoid on certain vehicle applications
Effective fix – restores control of 4WD system impacted by failed original solenoid
Thoroughly tested – on-vehicle and laboratory testing ensures trouble-free operation
Trustworthy quality – backed by team of designers and engineers in the United States

from

$56.99

This 4WD hub locking solenoid directly replaces the original equipment solenoid on certain vehicle years, makes and models.

Product Features:

Direct replacement – this 4WD hub locking solenoid matches the fit and function of the stock solenoid on certain vehicle applications
Effective fix – restores control of 4WD system impacted by failed original solenoid
Thoroughly tested – on-vehicle and laboratory testing ensures trouble-free operation
Trustworthy quality – backed by team of designers and engineers in the United States

from

$229.99

This 4WD actuator directly replaces the original equipment part on specific vehicle applications. It is reverse engineered to reliably restore proper functionality.

Product Features:

Direct replacement – this 4WD axle actuator directly replaces the original equipment part on specific vehicle years, makes and models
Effective fix – installation addresses inoperative four-wheel drive caused by failed original actuator
Smart solution – delivers reliable fit and function for competitive price
Trustworthy quality – backed by team of designers and engineers in the United States

from

$229.99

This 4WD actuator fork directly replaces the original equipment part on specific vehicle applications. It is reverse engineered to reliably restore proper functionality to the four-wheel drive system.

Product Features:

Ideal replacement – this 4WD actuator fork directly replaces the original equipment part on specific vehicle years, makes and models
Effective fix – installation addresses inoperative four-wheel-drive actuation caused by failed original equipment fork
Cost-effective solution – offers original equipment fit and function at a competitive price
Trustworthy quality – backed by a team of designers and engineers in the United States

from

$71.99

Carquest Premium Vehicle Solutions provides high-quality solutions for a wide range of applications. The 4WD Actuator ensures seamless transition between 2WD and 4WD modes, providing enhanced traction and stability on challenging terrains without manual intervention. Engineered for maximum performance and durability, our products are built to excel in even the most demanding conditions, ensuring reliable operation and long-lasting value.

Product Features:

Durable Construction: Designed with high-quality materials to withstand harsh environmental conditions, ensuring long-lasting performance in extreme temperatures, vibrations, and moisture exposure.
Precision Engineering: Accurate sensing and switching capabilities provide reliable performance, reducing the risk of malfunctions and improving vehicle safety and efficiency.
Easy Installation & Maintenance: Designed for quick installation and minimal upkeep, reducing downtime and repair costs for both manufacturers and consumers.
Fit/Form/Function: Each vehicle electronic component is engineered to meet or surpass OEM standards, ensuring precise fit, optimal functionality, and reliable performance.

from

$94.99

Carquest Premium Vehicle Solutions provides high-quality solutions for a wide range of applications. The 4WD Switch allows drivers to easily switch between 2WD and 4WD modes, offering greater control and flexibility for adapting to different driving conditions, such as off-road trails or slippery surfaces. Engineered for maximum performance and durability, our products are built to excel in even the most demanding conditions, ensuring reliable operation and long-lasting value.

Product Features:

Durable Construction: Designed with high-quality materials to withstand harsh environmental conditions, ensuring long-lasting performance in extreme temperatures, vibrations, and moisture exposure.
Precision Engineering: Accurate sensing and switching capabilities provide reliable performance, reducing the risk of malfunctions and improving vehicle safety and efficiency.
Easy Installation & Maintenance: Designed for quick installation and minimal upkeep, reducing downtime and repair costs for both manufacturers and consumers.
Fit/Form/Function: Each vehicle electronic component is engineered to meet or surpass OEM standards, ensuring precise fit, optimal functionality, and reliable performance.

from

$43.49

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$39.99

Durable Construction: Designed with high-quality materials to withstand harsh environmental conditions, ensuring long-lasting performance in extreme temperatures, vibrations, and moisture exposure.
Precision Engineering: Accurate sensing and switching capabilities provide reliable performance, reducing the risk of malfunctions and improving vehicle safety and efficiency.
Easy Installation & Maintenance: Designed for quick installation and minimal upkeep, reducing downtime and repair costs for both manufacturers and consumers.
Fit/Form/Function: Each vehicle electronic component is engineered to meet or surpass OEM standards, ensuring precise fit, optimal functionality, and reliable performance.

Most Popular 2001 Ford F-150 Transfer Cases

Customize your Ford with 18 Transfer Cases products like Transfer Case Gaskets, Transmission Transfer Case Motors, and Input Shaft Bearings, all priced under $144.99.

show more show less

from

$36.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$132.99

Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications
Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion
100% new – this transfer case motor is entirely new, not remanufactured like competitors
Quality assured – vehicle-specific application has been validation tested to ensure quality

from

$26.99

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$38.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$32.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$84.99

This transfer case control lever directly replaces the original equipment lever for specific vehicle years, makes and models.

Product Features:

Direct replacement – this 4WD shift linkage matches the fit and function of the original equipment on certain vehicle applications
Effective fix – restores proper operation after original lever fails
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$11.99

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications
Effective fix – restores a tight seal in the transfer case after original gasket fails
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$11.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$4.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$26.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific, providing unsurpassed quality for a seal you can trust
Validated for fit, form, and function
Engineered for the sealing repair environment
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$38.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$19.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$144.99

USA Standard Gear produces top quality transfer case small parts for repair and maintenance, including full top-to-bottom overhauls and rebuilds. USA Standard has one of the largest inventories of OEM and aftermarket transfer case component parts in the industry. Our large inventory and experienced tech support are two of the reasons we have been an industry leading supplier for decades. When you chose our transfer case small parts, you know you’re going to get the right part in stock backed by in-house quality assurance testing and expert knowledge.

Product Features:

BW4406 Transfer Case (Borg Warner)
Chain
1″ Wide

from

$132.99

TCaseBrg-SealKit

from

$62.99

The FAG repair sleeve is a precision element that provides additional sealing for damaged shafts. Made of heat-treated stainless steel, the FAG repair sleeve signifcantly increases the life of the shaft and prevents premature wear. Since no shaft removal or machining is required during the repair, the repair sleeve is a cost effective repair solution to protect damaged surfaces.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$52.99

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$9.29

TCaseOutputShaftSeal

from

$5.99

TCaseInputShaftSeal

Top Picks for 2001 Ford F-150 Drive Shafts and Axles

Upgrade Ford F-150s with top-quality Drive Shafts and Axles parts, including 81 OEM and aftermarket selections for your 2001 model.

show more show less

from

$45.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$22.49

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$13.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$40.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.48 INCH / 63 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
NOT PICTURED: TWO DUST SHIELDS

from

$9.99

This axle vent is designed to match the fit and function of the original vent on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this axle vent is designed to match the fit and function of the original vent on specified vehicles
Restores functionality – reliable replacement for an original vent that has failed due to blockage or fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$11.29

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$15.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$11.99

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$135.99

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$44.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$45.99

from

$21.49

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
COMPLETE MOUNT

from

$31.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$7.99

Wheel Lug Stud

from

$1544.99

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$542.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100 percent dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100 percent NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100 percent dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$52.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1559TV axle bearing and seal kit, TorringtonBrand, 2.530″ OD, 1.620″ ID This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.530″ O.D.
1.620″ I.D.

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$32.49

Product Features:

Brand may vary by location

from

$5.99

AXLE STUD , 58MM X M14-2.0 .

from

$7.99

Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.

Product Features:

Rear axle seal
2.530″ O.D.

from

$167.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$24.49

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$92.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1561TV axle bearing and seal kit, for Ford and Dodge, TorringtonBrand, 2.985″ OD, 1.700″ ID. This axle bearing & seal kit services one side only.

Product Features:

Fits Ford and Dodge applications
Includes axle bearing and seal
Torrington Brand
Services one side
2.985″ O.D.
1.700″ I.D.

In-Demand Differentials for 2001 Ford F-150s

Select from 410 premium Differentials parts for your 2001 Ford F-150, with prices ranging from $1.29 to $3,089.99.

show more show less

from

$14.49

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$10.49

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$69.99

Valvoline SAE 75W-140 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our formulation provides exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity and wear resistance, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. It’s recommended for conventional rear axles and transmissions requiring EP gear lubes under high speed, high load, high torque and high horsepower conditions.

Product Features:

EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -22F to 390F degrees
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$15.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$60.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$7.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$38.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$202.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$211.99

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$319.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

FORD 9.75 99-ON

from

$225.99

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$126.99

KIT BRG&SL FORD MSTR 8.8

from

$281.99

FORD 9.75 99-ON

from

$179.99

Product Features:

FRD 10BL 8.8 R/P 4.10A MG

from

$15.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$41.99

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$53.99

Product Features:

STRONG AND DURABLE – Controlled heat treatment process for strength and durability
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for durability and performance
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
Professional technicians know they can depend on National

from

$96.99

Product Features:

FRD 8.8″ INT. KIT 31 SPL OPEN 1987 & LATER ONLY

from

$6.79

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$27.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$204.99

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$137.99

MASTER KIT FORD 8.8″

from

$6.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Most Sold 2001 Ford F-150 Universal Joints

Explore our best-selling Ford parts for the 2001 F-150 among 34 OEM and aftermarket options starting from $4.59.

show more show less

from

$42.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$54.99

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$31.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$29.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$37.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$42.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$37.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$8.39

Universal Joint – Brute Force

from

$7.89

Universal Joint

from

$4.59

Universal Joint

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$5.49

Universal Joint – Brute Force

from

$5.39

Universal Joint

from

$40.99

from

$36.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$46.99

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$16.99

1350 & 1410 U/joint U-bolts, 3/8″ X 1-11/16″, kit.

Product Features:

u-joint u-bolt kit
Fits 1350 and 1410 u-joint size
Includes two u-bolts and four nuts

from

$63.99

Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.

from

$61.99

Yukon 1330 Dual-size cap U/Joint. 3.625″ snap ring span. One set of caps is 1.125″ in diameter and the other is 1.062″. Outside snap ring.

from

$51.99

Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.

Top-Rated Drivetrains Brands For Your 2001 Ford F-150

Shop for the best-rated brands offering Drivetrains and other products for your 2001 Ford F-150s. Below you’ll find some of our best rated Drivetrains from National, Dorman, and Motive Gear, and more. Drivetrains from these brands that fit a 2001 F-150 start at just $7.99 and are rated as high as 4.3 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular National 2001 Ford F-150 Drivetrains

When it comes to maintaining or upgrading your 2001 Ford F-150, using quality Drivetrains is essential to ensure durability and a perfect fit. National ticks all of those boxes. We offer a wide selection of National Drivetrains, specifically designed for the 2001 Ford F-150. With over 3 National brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $7.99, with an average price of just $19.49. Plus, with over 14 customer reviews and an average rating of 4.3 stars, you can trust that our National Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $13.99

(9)

Bearing

“as advertised”

from $36.49

(1)

Shaft Repair Sleeve

“Fixed my Ford F-150 4.2. Fit well and installation tool seated the sleeve exactly where it needed to be. Super easy to use and covered the grooved s”

from $7.99

(4)

Bearing Race

“Goes with M88010 bearing cup. Application was the pinion bearing race for a Ford 9 Inch on a 1957 Ford F-100.”

Popular Dorman 2001 Ford F-150 Drivetrains

Dorman auto parts is one of the highest quality Drivetrain brands in the market. Any 2001 Ford F-150 owner should feel confident when installing genuine Dorman parts in their vehicle. To ensure the best fit and performance for your 2001 F-150, Advance Auto Parts carries a full inventory of 3 Dorman Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these Dorman Drivetrains range from $9.99 to $60.99, plus, with more than 21 customer reviews and an impressive 4.2 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $9.99

(6)

Axle Differential Vent

“Does also work on 85 f250 with a dana 70 u”

from $60.99

(14)

Differential Cover

“installation was easy and part worked as it should have”

from $22.49

(1)

Driveshaft Flange Bolts

“This item appears to be correct and my review is more of a bashing of AA help desk who apparently does not answer questions as you are lead to believe”

FAQs for 2001 Ford F-150 Drivetrains

Which Drivetrains are best-sellers for 2001 Ford F-150s?

Out of 563 Drivetrains that fit 2001 Ford F-150s, the following parts are the top sellers:

Greaseable Premium Universal Joint (10086740) – $34.99
DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart (12079139) – $11.99
Axle Housing Cover Gasket Rectangular Shaped, 10 Bolt Hole Gasket (5782406) – $15.99

What’s the price range for 2001 Ford F-150 Drivetrains?

Drivetrain prices for the 2001 Ford F-150 start at $1.29 and go up to $3,089.99 for the most premium parts.

What’s the average price of a Drivetrain for a 2001 Ford F-150?

The average price for Drivetrains for the 2001 Ford F-150 is $329.53. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford F-150 model years?

Yes, we currently carry Drivetrains for 31 model years of Ford F-150s between 1977 and 2025. Drivetrains are bought most frequently for the following model years: 2023, 2022, 2021, 2020, 2019, 2018, 2017, 2016, and 2015.

What are the cheapest Drivetrains for my 2001 Ford F-150?

The cheapest 2001 Ford F-150 Drivetrains we carry in stock are:

Differential Ring Gear Bolt (10282257) – $1.29
Ring Gear Bolt (20520509) – $1.99
Ring Gear Bolt (20520495) – $2.99
Differential Cross Shaft (10282201) – $2.99
Differential Crush Sleeve (10282338) – $2.99

What are the top-rated Drivetrains that fit the 2001 Ford F-150?

Out of 24,823 reviews by customers, our 2001 Ford F-150 Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 2001 Ford F-150 and their top-rated products:

4WD Components
- Solenoid, 4WD Disengage and Emissions Purge (10086500) – $53.99
- Solenoid, 4WD Engage and Emissions Purge (10086502) – $56.99
- 4WD Vacuum Actuator, Axle (20640684) – $229.99
Universal Joints
- Solenoid, 4WD Disengage and Emissions Purge (10086500) – $53.99
- Solenoid, 4WD Engage and Emissions Purge (10086502) – $56.99
- 4WD Vacuum Actuator, Axle (20640684) – $229.99
Spindles
- Solenoid, 4WD Disengage and Emissions Purge (10086500) – $53.99
- Solenoid, 4WD Engage and Emissions Purge (10086502) – $56.99
- 4WD Vacuum Actuator, Axle (20640684) – $229.99

What types of Drivetrains do you sell for my 2001 Ford F-150?

As of 11/2/25, these are some of the most in-demand types of Drivetrains for a 2001 Ford F-150:

Can I get help with 2001 Ford F-150 Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford F-150 Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford F-150 Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

2001 Ford F-150 Drivetrains

Spartan – Drive Axle Assembly; Ford F-150 00-04 Axle (Part No.RAX2021D)

Idemitsu – Type HP Automatic Transmission Fluid , 1 Quart (Part No.10107-042F)

Yukon Gear – Replacement Axle Stud For Dana 44 & Model 35 (Part No.33171)

Dorman – Transfer Case Gasket (Part No.917-522)

Powertrax – Lock Right Locker (Part No.2510-LR)

Yukon Gear – Pinion Nut (Part No.33154)

Yukon Gear – Air Line Repair Kit, Zip Locker (Part No.34003)

Yukon Gear – Spindle Nut For Dana 30 & Dana 44, .372" Thick (Part No.33474)

Carquest Premium – CV Axle Shaft Assembly (Part No.NCV428573)

Yukon Gear – Left Inner Axle Replacement Seal For Dana 44, 50, Model 35 IFS (Part No.30138)

Dorman – 4WD Transfer Case Motor Assembly (Part No.600-571)

FAG US – Bearing (Part No.BR1682)

Yukon Gear – 10.6" Ford Outer Slinger (Part No.33199)

Yukon Gear – Crush Sleeve (Part No.33085)

Yukon Gear – Axle O-Ring For Ford 10.25" & 10.5" (Part No.33465)

Dorman – Uni-Fit C.V. Joint Boot Kit Outer greater than 3.58 In. Diameter (Part No.614-003)

Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Sold by each) (Part No.618-033)

Dorman – Differential Clutch Kit (Part No.697-780)

Motive Gear – Differential Ring and Pinion (Part No.D44-456)

Yukon Gear – DrvShftPinYoke (Part No.33574)

National – Shaft Repair Sleeve (Part No.99114)

Spicer – Universal Joint (Part No.5-1350X)

National – Bearing (Part No.M88048)

Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)

ARP Auto Racing – For Use With Ford 8.8 And 9" Using 3/4"Socket, 0.75"L Under Head, 7/16"-20 (Part No.250-3003)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.371)

Yukon Gear – Differential Side Be (Part No.55079)

Yukon Gear – Bearing Race Driver (Part No.56010)

Dorman – Solenoid, 4WD Disengage and Emissions Purge (Part No.600-401)

Dorman – Solenoid, 4WD Engage and Emissions Purge (Part No.600-400)

Dorman – 4WD Vacuum Actuator, Axle (Part No.600-300)

Dorman – Differential Shift Fork (Part No.600-560)

Carquest Premium – 4WD Actuator (Part No.EGA1274)

Carquest Premium – 4WD Switch (Part No.FWC1087)

Carquest Premium – Multi-Use Connector (Part No.PTA1771)

Carquest Premium – 4WD Actuator (Part No.EGA1444)

National – Shaft Repair Sleeve (Part No.99187)

Dorman – Transfer Case Shift Motor (Part No.600-802)

National – Multi-Purpose Seal (Part No.4503N)

National – Multi-Purpose Bearing (Part No.208)

National – Multi-Purpose Bearing (Part No.207)

Dorman – Transfer Case Shift Linkage (Manual Shift Only) (Part No.600-603)

Dorman – Transfer Case Gasket (Part No.917-522)

Driveworks – Taper Bearing Cone (Part No.S-M-88048)

Driveworks – Oil Seal (Part No.S-3946)

Felpro – Transfer Case Adapter Gasket (Part No.55484)

National – Shaft Repair Sleeve (Part No.99189)

National – Multi-Purpose Seal (Part No.710664)

USA Standard Gear – Transfer Case BW4406 Wide Chain (Part No.72057)

USA Standard Gear – TCaseBrg-SealKit (Part No.76401)

FAG US – Repair Sleeve (Part No.SR3501)

FAG US – General Seal (Part No.SS2911)

USA Standard Gear – TCaseOutputShaftSeal (Part No.72252)

USA Standard Gear – TCaseInputShaftSeal (Part No.75651)

Spicer – Universal Joint, Greaseable 1410 Series (Part No.5-160X)

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

National – Bearing (Part No.M88048)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

Dorman – Axle Differential Vent (Part No.924-263)

National – Multi-Purpose Bearing (Part No.FC-66998)

Driveworks – Universal Joint (Part No.DW-331BL)

National – Multi-Purpose Seal (Part No.8835S)

Carquest Premium – CV Axle Shaft Assembly (Part No.NCV11123)

Spicer – Universal Joint, Greaseable 1350 Series (Part No.5-178X)

Spicer – Universal Joint (Part No.5-1350X)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

Driveworks – Cylindrical Bearing (Part No.S-R1561TV)

Yukon Gear – Wheel Lug Stud (Part No.33571)

Spartan – Drive Axle Assembly; Ford F-150 01-04 Axle (Part No.RAX2025F)

Cardone – Drive Shaft: Greasable, Direct Replacement (Part No.65-9545)

Yukon Gear – R1559Tv Rear Axle Bearing And Seal Kit (Part No.10001)

Yukon Gear – C/Clip (Part No.33083)

Driveworks – Wheel Bearing (Part No.S-RP-1561-FO)

Yukon Gear – Axle Stud , 58Mm X M14-2.0 (Part No.33557)

Yukon Gear – Axle Seal, For 1559 Or 6408 Bearing (Part No.30201)

National – Drive Shaft Center Support Bearing (Part No.HB-88515)

National – Multi-Purpose Bearing (Part No.HK-4012)

Yukon Gear – R1561Tv Rear Axle Bearing And Seal Kit (Part No.10002)

Valvoline – DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.822405)