1997 Mercury Mountaineer Performance and Racing Products
More 1997 Mercury Mountaineer Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1997 Mercury Mountaineer, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1997 Mercury Mountaineer Performance and Racing Products
Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)
from
$43.99
Super Intake Manifold Bolts
Edelbrock – Throttle Body, 90mm, Pro-Flo XT, Ford-Style, Black Powder Coated Finish (Part No.38183)
from
$429.99
The Edelbrock #38183 is a single-bore 90mm throttle body designed with a 5.0L Ford-style base pad. It is fully machined and assembled by Edelbrock. It includes a Throttle Position Sensor, a progressive throttle cable lever, and cruise and kick-down attach
See More
FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2941)
from
$48.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
- Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)
from
$38.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.
Product Features:
See More
Product Features:
- Heat treated black oxide coated Grade 8 alloy steel
- Thick parallel ground washer provides more accurate, uniform torque
- Hex Prevents Socket Slippage
- Accurate And Uniform Torque
- Black Plated Finish
Mr. Gasket – Oil Pan Bolt Kit (Part No.6087)
from
$30.19
The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.
Product Features:
See More
Product Features:
- Ideal For Tight Spaces
- Serrations Prevent Loosening
- Flange Distributes Pressure
- Zinc Plated Bolts
- Grade 5 Material
- Easy Installation
Mr. Gasket – Aluminum Exhaust Gasket (Part No.7410G)
from
$42.99
Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.
Product Features:
See More
Product Features:
- Reusable header, exhaust manifold and collector flange gaskets
- Manufactured from “dead soft” aluminum layers – .125″ thick
- Conforms easily to surface irregularities (warped flanges)
- Compresses down to 0.060″ to create a tight leak-proof seal
- Will not shrink, deteriorate, or blow out- eliminating gasket leaks
- For high performance street, drag race and oval track use
Motive Gear – Performance Differential Ring and Pinion (Part No.F888514)
Fram – High Perf. Full-Flow Lube Spin-on (Part No.HP1)
from
$16.99
FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**
Product Features:
See More
Product Features:
- Proven protection for up to 10,000 miles
- Engineered for use with synthetic or conventional motor oils
- Filter media is a blend of fiber and resin that captures 95% of the dirt particles
- The perfect balance of dirt-trapping efficiency and dirt-holding capacity
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1684)
from
$46.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Rigid core, molded silicone rubber gaskets provide for ease of installation, and are great for on-again/off-again situations (like setting valve lash).
- Features high-tech silicone material for long life, a solid steel core for strength and durability, and stainless steel compression limiters to prevent
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1809)
from
$25.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
Mallory – Distributor Wiring Harness (Part No.29349)
Mr. Gasket – Intake Manifold Bolts (Part No.958G)
from
$19.99
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers
Product Features:
See More
Product Features:
- Hex Head
- Zinc Plated
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)
from
$237.99
The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.
Product Features:
See More
Product Features:
- Cost effective aluminum construction provides superior strength to weight ratio
- Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
- Durable design increases valve lift while withstanding the rigors of moderate race use
- Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
Mr. Gasket – Ultra Seal: Sure-Lock Rocker Arm Nuts (Part No.923G)
from
$87.19
Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.
Product Features:
See More
Product Features:
- (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
- Shank O.D. .540″
- Includes Locks and Hex Wrench
- High-Quality Grade Steel
- Heat-Treated For Ex Strength
- Plated With Durable Gold Tone Finish
K&N – Cold Air Intake: Guaranteed To Increase Horsepower, With Million Mile Air Filter (Part No.57-2513-1)
from
$299.99
The K&N 57-2513-1 FIPK air intake system replaces the restrictive factory air filter and air box. K&N intakes are designed to dramatically reduce intake restriction and improve air flow. This allows your engine to inhale a larger amount of air than the factory air filter assembly. More air means more usable power and acceleration throughout the engine’s RPM range. The 57-2513-1 air intake comes with a chrome topped K&N high-flow air filter that installs onto the factory mass air sensor within the previous air box space. Air is directed through the air filter into the engine’s throttle body for a guaranteed power gain. The oversized cone shaped air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less using existing factory mounting points. The tools needed are a screwdriver, vise grips and several wrenches.
Product Features:
See More
Product Features:
- GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
- BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
- IMPROVED ENGINE SOUND: Hear the power under the hood.
- WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
- EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
- EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
- DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
- HIGH QUALITY: Made in America.
K&N – Cold Air Intake: Adds Up To 9 Horsepower, With Million Mile Air Filter (Part No.57-2539)
from
$349.99
The K&N 57-2539 FIPK air intake system replaces the restrictive factory air filter and air intake. K&N intakes are designed to dramatically reduce intake restriction as they smooth and straighten air flow. This allows your engine to inhale a larger amount of air than the factory air filter assembly. More air means more usable power and acceleration throughout the engine’s RPM range. The 57-2539 air intake comes with a chrome topped K&N high-flow air filter and a heat shield that installs into the previous air box space. Air is directed through an aerodynamically engineered intake tube into the engine’s throttle body for a guaranteed power gain. The tube accommodates the factory mass air sensor, idle bypass hose and crank case vent hose. The oversized cone shaped air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less using existing factory mounting points. The tools needed are a screwdriver, a ratchet set and several wrenches.
Product Features:
See More
Product Features:
- GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
- BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
- IMPROVED ENGINE SOUND: Hear the power under the hood.
- WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
- EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
- EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
- DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
- HIGH QUALITY: Made in America.
Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)
from
$100.99
Product Features:
See More
- Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
- Set of 16
- 1.50 in. Outside Diameter
- Steel Material
- Black Oxide Finish
Energy Suspension – Control Arm Bushing Set (Part No.4.3157R)
from
$102.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Edelbrock – Front Timing Cover Gasket Set #6991 For Small-Block Ford, With Front Seal (Part No.6991)
from
$28.99
Available in kits including front cover gasket, crankshaft seal, fuel pump and water pump gasket or including cover gasket and front seal.
Product Features:
See More
Product Features:
- Timing Cover Gasket And Oil Seal Kit
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 5 Piece Set (Part No.1248)
from
$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 11 Piece Set (Part No.1250)
from
$33.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Mr. Gasket – Water Neck (Part No.2662)
from
$19.99
Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.
Product Features:
See More
Product Features:
- Chrome Plated
- This Is A 45 Degree Neck
- Comes With O-ring And Bolts
- Has Small Hose Fitting On It
SCT Performance – Preloaded Performance Programmer for Increased Horsepower & Torque (Part No.7015)
from
$456.99
The X4 Performance Programmer connects high-performance tunes to your vehicle for an immediate boost in horsepower and torque. Awaken your engine to its maximum real potential with preloaded, dyno-proven tune files through the easy-to-use functionality. Instantly increase horsepower and torque and customizeModify a variety of parameters at the touch of a button, all while monitoring gauges on a customizable display.
Product Features:
See More
Product Features:
- Read vehicle performance data on a full-color LCD display for easy viewing, day or night.
- Preloaded, street-tested, dyno-proven tunes boost horsepower, torque, and throttle sensitivity.
- Reads and clears DTC (Diagnostic Trouble Codes) with ease.
- Load up to 10 custom tune files created by any SCT Custom Tuning Dealer.
- Full color LCD display
- High-speed data logging/monitoring
- Dual analog inputs
- Most popular vehicles supported
- Installs quickly and easily
- Easy restoration back to stock
- User adjustable vehicle parameters
- USB Interface cable included
- Product might not be available in all states due to local laws.
Accel – Handheld Computer Programmer for Enhanced Performance and Tuning Control (Part No.49505)
from
$390.99
Revolutionary handheld tuner quickly and easily reprograms your vehicle for more power across the entire rpm range! 50 State Legal!
Product Features:
See More
Product Features:
- Average gains in excess of 30 HP/40 ft.-lbs. for gas and 80 HP/150 ft.-lbs. diesel*
- HD 2.8¿ color screen with updated interface for easier and faster modifications
- HD 2.8┐ color screen with updated interface for easier and faster modifications
- Increased memory and faster processor for improved tuning plus faster updating
- Active fuel management control*
- Performance test (0-60, ╝ mile testing)
- Performance test (0-60, ¼ mile testing)
- Internet updating using PC software
- Tire size adjustment
- Axle gear ratio adjustment
- Shift point and firmness adjustment*
- Speed and rev limiter adjustments*
- Carb EO # D-745
- Diagnostic capability ¿ read and clear trouble codes with explanation of codes
- Diagnostic capability ┐ read and clear trouble codes with explanation of codes
Popular 1997 Mercury Mountaineer Performance and Racing Products Categories
1997 Mercury Mountaineer Performance and Racing Products
You count on your 1997 Mercury Mountaineer to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 33 Performance and Racing Products ranging in price from $16.99 to $456.99, you’re sure to find everything you need for your 1997 Mercury Mountaineer.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 12 different brands like K&N, FEL-PRO Performance, and Mr. Gasket. 1997 Mercury Mountaineer Performance and Racing Products start as low as $16.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 137 extensive product reviews on 1997 Mercury Mountaineer Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Water Neck with 3.8 stars and High Perf. Full-Flow Lube Spin-on with 4.0 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1997 Mercury Mountaineer below to get started!
Top-Rated Performance and Racing Products Brands For Your 1997 Mercury Mountaineer
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1997 Mercury Mountaineer running right for years to come. In our inventory you’ll find brands like K&N, FEL-PRO Performance, Mr. Gasket, and even more.
Popular K&N Performance and Racing Products
You’ll find popular K&N brand products across Performance Air Intake Kits and Performance Oil Filters. All are waiting to get your 1997 Mercury Mountaineer back on the road. Some of the top-rated K&N products in these categories are:
from
$299.99
(4)
Cold Air Intake: Guaranteed To Increase Horsepower, With Million Mile Air Filter
Performance Air Intake Kits
from
$17.99
(99)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
FAQs for 1997 Mercury Mountaineer Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1997 Mercury Mountaineer?
Out of 33 Performance and Racing Products for the 1997 Mercury Mountaineer, the most popular in our inventory are:
from
$33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets
from
$456.99
(1)
Preloaded Performance Programmer for Increased Horsepower & Torque
Computer Chip Programmers
What are the top-rated 1997 Mercury Mountaineer Performance and Racing Products?
Top-rated Performance and Racing Products for your 1997 Mercury Mountaineer based on customer reviews/ratings are:
from
$19.99
(12)
Water Neck
“FINALLY… first time not having to re-do flimsy paper gaskets.
Aside from thicker cork gasket, O ring is only way to go !”
from
$16.99
(4)
High Perf. Full-Flow Lube Spin-on
“Filter size for my boat. OMC 460. works fine. HP filters have a bypass so that clogs do not cause the engine to starve for oil… important for HP eng”
from
$85.29
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”
