1997 Ford F-350 Pickup Performance Exhaust Products

Essential 1997 Ford F-350 Pickup Performance Exhaust Products

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound (Part No.842451)

50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound

from

$175.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound (Part No.8042441)

40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound

from

$123.99
The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – Super 40 Series Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Aggressive Sound (Part No.952546)

Super 40 Series Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Aggressive Sound

from

$133.99
The Super 40 features Flowmaster’s Delta Flow technology. It’s larger case profile provides the best of both worlds of performance and sound. The Super 40 has that deep powerful sound of the Original 40 series but with all the benefits of performance and low interior resonance from the Delta Flow technology. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – Delta 40 Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Aggressive Sound (Part No.842541)

Delta 40 Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Aggressive Sound

from

$154.99
This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over standard 40 series. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 50 Series Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Moderate Sound (Part No.52556)

50 Series Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Moderate Sound

from

$185.99
The Super 50 series muffler is a larger version of Flowmaster’s 50 series Delta Flow muffler. Originally designed for trucks and SUV’s, it is also well suited to muscle car and high performance applications. In addition, the larger case size significantly reduces interior resonance and provides a deep, rich tone along with mileage and power gains. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Edelbrock – Exhaust Manifold Gasket Set for Ford (Part No.7262)

Exhaust Manifold Gasket Set for Ford

from

$28.99
Product Features:
  • Designed To Match Port Openings Of Cylinder Heads
  • Excellent Free-Flowing Seal
See More

Hooker Headers – Super Competition Header Gasket (Part No.10825HKR)

Super Competition Header Gasket

from

$17.79
Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.

Product Features:
  • Tear Resistant
  • Precisely Cut To Match Header
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1468)

Exhaust Manifold Gasket Set

from

$45.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5930)

Ultra Seal: Exhaust Gasket Set

from

$37.49
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Withstands Intense Exhaust Heat
  • Graphite-Impregnated Facing
  • Steel Expanded Metal Core
  • Superior Tensile Strength
  • Resists Deteriorating
  • Anti-stick Properties
  • Easy Removal For Disassembly
See More

Mr. Gasket – Exhaust Gasket Set (Part No.253)

Exhaust Gasket Set

from

$29.49
Manufactured from high-temperature composite exhaust material. Provides maximum torque retention to eliminate gasket failure. Can be trimmed if necessary for modified port applications. Precision die cut for an excellent fit. For OE replacement, high-performance street, drag race and oval track.

Product Features:
  • High-Temperature Exhaust Material
  • Withstands Extreme Exhaust Heat
  • Excellent Sealing Durability And Torque Retention
  • Superior Tensile Strength
See More

Mr. Gasket – Aluminum Exhaust Gasket (Part No.7411G)

Aluminum Exhaust Gasket

from

$39.99
Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.

Product Features:
  • Reusable header, exhaust manifold and collector flange gaskets
  • Manufactured from “dead soft” aluminum layers – .125″ thick
  • Conforms easily to surface irregularities (warped flanges)
  • Compresses down to 0.060″ to create a tight leak-proof seal
  • Will not shrink, deteriorate, or blow out- eliminating gasket leaks
  • For high performance street, drag race and oval track use
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1419)

Exhaust Manifold Gasket Set

from

$26.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1416)

Exhaust Manifold Gasket Set

from

$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Exhaust Gasket Set (Part No.264G)

Exhaust Gasket Set

from

$36.49
Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

Product Features:
  • Manufactured from high-temperature acrylic blend exhaust material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
  • Precision Die Cut For Excellent Fit
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1442)

Exhaust Manifold Gasket Set

from

$33.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1447)

Exhaust Manifold Gasket Set

from

$38.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5928)

Ultra Seal: Exhaust Gasket Set

from

$38.59
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Manufactured from high-temperature steel core/graphite faced exhaust material
  • Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
  • Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
  • Conforms to and seals minor surface irregularities
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
  • Anti-Stick Properties
  • Easy Removal For Disassembly
See More

Mr. Gasket – Exhaust Gasket Set (Part No.254G)

Exhaust Gasket Set

from

$35.99
Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

Product Features:
  • Manufactured from high-temperature acrylic blend exhaust material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
  • Precision Die Cut
See More

Mr. Gasket – Ultra Seal; Exhaust Gasket Set (Part No.5951)

Ultra Seal; Exhaust Gasket Set

from

$36.99
Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:
  • Graphite-Impregnated Facing
  • Steel Expanded Metal Core
  • Superior Tensile Strength
  • Resists Cracking
  • Withstands Intense Heat
  • Resists Deteriorating
  • Anti-Stick Properties
  • Easy Removal For Disassembly
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1467)

Exhaust Manifold Gasket Set

from

$45.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Aluminum Exhaust Gasket (Part No.7410G)

Aluminum Exhaust Gasket

from

$42.99
Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.

Product Features:
  • Reusable header, exhaust manifold and collector flange gaskets
  • Manufactured from “dead soft” aluminum layers – .125″ thick
  • Conforms easily to surface irregularities (warped flanges)
  • Compresses down to 0.060″ to create a tight leak-proof seal
  • Will not shrink, deteriorate, or blow out- eliminating gasket leaks
  • For high performance street, drag race and oval track use
See More

Mr. Gasket – Ultra Seal; Exhaust Gasket Set (Part No.5954)

Ultra Seal; Exhaust Gasket Set

from

$35.99
Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:
  • Graphite-Impregnated Facing
  • Steel Expanded Metal Core
  • Superior Tensile Strength
  • Resists Cracking
  • Withstands Intense Heat
  • Resists Deteriorating
  • Anti-Stick Properties
  • Easy Removal For Disassembly
See More

Mr. Gasket – Copper Seal: Exhaust Gasket Set (Part No.7160)

Copper Seal: Exhaust Gasket Set

from

$60.29
Mr. Gasket CopperSEAL Header Gaskets are a high quality copper gasket that performs extremely well and are reusable. We recommend this in all racing and high performance applications. They are for stock heads unless indicated, and work well in high heat and turbocharged applications.

Product Features:
  • Manufactured from ¿Dead Soft¿ (solid) .043″ thick copper material
  • Manufactured from ┐Dead Soft┐ (solid) .043″ thick copper material
  • .051″ embossment around each exhaust port to seal irregular surfaces. Total gasket thickness .094″
  • Provides excellent sealing and durability
  • Conforms to and seals minor surface irregularities
  • For high performance street, drag race, oval track and turbocharged (extreme heat) applications
See More

Hooker Headers – Super Competition Header Gasket (Part No.10820HKR)

Super Competition Header Gasket

from

$19.99
Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.

Product Features:
  • Tear Resistant
  • Precisely Cut To Match Header
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1430)

Exhaust Manifold Gasket Set

from

$26.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

1997 Ford F-350 Pickup Performance Exhaust Products

Maybe you’re in the middle of a full rebuild of that 1997 Ford F-350 Pickup. Maybe you just need a couple of Performance Exhaust Products. Either way, Advance Auto Parts has 5 different Performance Exhaust Products in our inventory ranging from $19.99 to $154.99. That means you can find the exact parts or products you need to keep that 1997 Ford F-350 Pickup running smoothly.

Performance Exhaust Products are only as good as their brand. We stock 3 different brands to make sure you have plenty of trusted parts to choose from for your 1997 Ford F-350 Pickup. Hooker Headers, FEL-PRO Performance, and Flowmaster Inc. are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Exhaust Products for your 1997 Ford F-350 Pickup, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.

So if you’re in the market for aftermarket Performance Exhaust Products to keep your 1997 Ford F-350 Pickup rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Exhaust Products Brands To Make Your 1997 Ford F-350 Pickup Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1997 Ford F-350 Pickup demands trusted brand parts and products to keep it running. Many trusted brands of Performance Exhaust Products make up Advance Auto Parts’ inventory, and all are ready to help make your F-350 Pickup the best it can be. Be sure to browse some of our top Performance Exhaust Products brands and parts.

Popular Hooker Headers Performance Exhaust Products

We carry Hooker Headers parts in our stock across Performance Exhaust Manifold Gaskets categories, plus more. For a 1997 Ford F-350 Pickup, our most popular Hooker Headers Performance Exhaust Products include:
Super Competition Header Gasket
from $19.99
(1)
Super Competition Header Gasket
Performance Exhaust Manifold Gaskets

FAQs for 1997 Ford F-350 Pickup Performance Exhaust Products

What are the most purchased Performance Exhaust Products for the 1997 Ford F-350 Pickup?

Out of 5 Performance Exhaust Products for the 1997 Ford F-350 Pickup, the most popular in our inventory are:
Exhaust Manifold Gasket Set
from $45.99
This product is not rated
Exhaust Manifold Gasket Set
Performance Exhaust Manifold Gaskets
Delta 40 Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Aggressive Sound
from $154.99
This product is not rated
Delta 40 Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Aggressive Sound
Performance Exhaust Mufflers
Super 40 Series Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Aggressive Sound
from $133.99
This product is not rated
Super 40 Series Muffler, 2.5in Offset Inlet 2.5in Center Outlet, Non-Reversible, Aggressive Sound
Performance Exhaust Mufflers