from

$5.99

0.260″ diameter cross pin roll pin for 8.75″ Chrysler, 8″, 9″ Ford, and Model 20 and 35.

Product Features:

Roll pin for Chrysler 8.75″, Ford 8″ and 9″, AMC Model 20 and Model 35
0.260″ diameter

from

$96.99

Product Features:

FRD 8.8″ INT. KIT 31 SPL OPEN 1987 & LATER ONLY

from

$109.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

Machined bodies to meet the tight tolerances
Forged and cast material to meet the performance requirement
Minimize the flash lines for less interference
Cleaning process induces compressive strength for increased performance
Machined and threaded holes for mounting ease
Rust preventative added for longer shelf life

from

$15.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$179.99

Product Features:

FRD 10BL 8.8 R/P 3.55A MG

from

$123.99

Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:

Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications
Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion
100% new – this transfer case motor is entirely new, not remanufactured like competitors
Quality assured – vehicle-specific application has been validation tested to ensure quality

from

$52.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1559TV axle bearing and seal kit, TorringtonBrand, 2.530″ OD, 1.620″ ID This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.530″ O.D.
1.620″ I.D.

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$56.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$4.99

This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$15.27

MT Output Shaft Seal

from

$6.99

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$231.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$165.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2009 and down Ford 8.8″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$28.96

With Clamps and Grease The EMPIRE CV Joint Boot Kit is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function. Install one boot kit per wheel to restore vehicle to optimal condition and protect the constant velocity joint from contamination

Product Features:

Help restore the vehicle to like-new condition
Constructed of high strength OE materials
Resists environmental contamination
Protects the CV joint from premature failure

from

$7.99

ZIP locker front switch cover.

Product Features:

Cover for switch
Front

from

$28.99

The components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of an axle of a vehicle or trailer. Check the leaf spring dimensions and other relevant application details to select the right type and size U-bolt kit for your needs.

Product Features:

Reliable hardware – the components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of a vehicle or trailer axle
Check fit – carefully review the dimensions of the leaf springs that will be used and other relevant application details to select the right type and size U-bolt kit for your needs
Durable construction – the components in this kit are engineered from quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$399.99

8.8″ Ford low profile TA HD Aluminum rear Cover. This cover will not fit vehicles with independent rear suspension.

Product Features:

Fits Ford 8.8″
Aluminum girdle cover

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles
Quality materials – all components are built for reliable longevity and performance
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$48.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$5.99

AXLE STUD , 58MM X M14-2.0 .

from

$917.99

Evolution Driveline products, are remanufactured to meet or exceed OEM specifications for quality, fit, and performance. Every transfer case we sell passes a comprehensive battery of tests on our computerized test center. We recreate actual driving conditions and analyze performance before the product even leaves the factory, so you can buy with confidence.

Product Features:

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$12.99

8.8″ Ford cover gasket.

Product Features:

Cover gasket
Fits Ford 8.8″

from

$52.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$39.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.