1994 Ford E-250 Econoline Performance and Racing Products

Essential Performance and Racing Products for 1994 Ford E-250 Econolines

Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)

Tie Rod Dust Boot

from

$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:
  • Easy to Install
  • Superior Material
  • Saves Your Tie Rods
  • Lasts Longer
  • Looks Great
See More

Edelbrock – Performer-Plus camshaft for Small-Block Ford 351W V-8 applications (Part No.2182)

Performer-Plus camshaft for Small-Block Ford 351W V-8 applications

from

$339.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched to Edelbrock Performer Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

Energy Suspension – Hyper-Flex System (Part No.4.18116G)

Hyper-Flex System

from

$229.99
Product Features:
  • Incredible Improvement in Control
  • Maintains Proper Caster and Camber Alignment
  • Increase in Handling and Control
  • Greatly Reduce Wheel Hop on Quick Acceleration
  • Even Braking Control is Improved
  • Better Suspension Stability
See More

Accel – Ford Tfi Modulator 1983-96 (Part No.35368)

Ford Tfi Modulator 1983-96

from

$96.99
This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most Ford Thick Film Ignition systems. 1983 thru 1996.

Product Features:
  • Fits Most Stock And Modified Distributors
  • Dwell Control Circuit
  • Resists False Triggering
See More

Spectre – Oil Pan (Part No.5507)

Oil Pan

from

$103.99
Spectre’s Oil Pan was designed for Ford cars and 2WD trucks with 221, 260, 289, & 302W engines (will not fit vans and 4WD vehicles). The stock 4 quart capacity pan features a raw finish and durable steel construction. Precision engineered for optimum fit and function, this high quality OEM replacement part is easy to install.

Product Features:
  • For Ford cars and 2WD trucks with 221, 260, 289, & 302W engines
  • Stock 4 quart capacity
  • Raw, unfinished steel construction
  • Does not fit vans and 4WD vehicles
See More

Motive Gear – Performance Differential Ring and Pinion (Part No.F888355)

Performance Differential Ring and Pinion

from

$229.99


Product Features:
  • FRD 10BLT 8.8 R/P 3.55 MGP
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1018)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$49.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1614)

Engine Valve Cover Gasket Set

from

$25.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Die cut silicone rubber gaskets conform to out-of-flat covers
  • Great for on-again/off-again situations
  • Not intended for use in emission controlled vehicles.
See More

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud (Part No.19043-16)

Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud

from

$427.99
These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Ford V8 289-302-351W applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:
  • CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
  • Designed for high performance street and race engines
  • Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
  • Additional clearance, up to 1.650″ O.D. valve spring
See More

Accel – Distributor Cap And Rotor Kit (Part No.8223)

Distributor Cap And Rotor Kit

from

$28.88


Product Features:
  • Heavy Duty Cap and Rotor Kit
  • With Brass Inserts
See More

Dorman – Clutch Fan Blade: Steel, Cost Effective And Reliable (Part No.620-154)

Clutch Fan Blade: Steel, Cost Effective And Reliable

from

$79.99
Replace your damaged cooling fan blade with this direct replacement. This vehicle-specific application is engineered for a perfect fit and is made from quality materials to ensure durability and restore proper cooling system operation.

Product Features:
  • Direct replacement – this engine cooling fan blade fits and functions like the original equipment fan blade.
  • Quality construction – manufactured from premium materials for a long service life.
  • Excellent value – original equipment quality at a lower price
  • Quality tested – has undergone testing to ensure proper fit and performance
See More

Edelbrock – VALVE COVERS (Part No.4260)

VALVE COVERS

from

$144.99
Product Features:
  • Polished Finish
  • Raised Fins w/Black Mat Background
  • Detailed With Allen Hex Heads
  • 2 Piece Look; 1 Piece Construction
  • Clears Most Roller Rockers
  • Clears Valvetrain Components
  • Heavy Gauge
See More

Mr. Gasket – Precision Timing Tape (Part No.1594)

Precision Timing Tape

from

$21.79
Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:
  • 6 3¿8″ diameter
  • 6 3┐8″ diameter
  • 289-302-351 cu. in.
  • Increased Performance
  • Set Valve Lash At Proper Time
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 11 Piece Set (Part No.1250)

Lower Intake Manifold Gasket Set: 11 Piece Set

from

$33.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
  • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
  • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
  • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
  • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
See More

Edelbrock – Pushrod Set for Small Block Ford 289-302 (Part No.9632)

Pushrod Set for Small Block Ford 289-302

from

$210.99
Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1468)

Exhaust Manifold Gasket Set

from

$45.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

MSD Ignition – Distributor Cap; Ford HEI (Part No.8408)

Distributor Cap; Ford HEI

from

$52.99
MSD molds our most popular V8 distributor caps in-house. These caps are injection molded from DuPont? Rynite material and feature spark plug-style terminals. These terminals offer improved locking connections and the Rynite material is extremely strong with excellent dielectric properties. Plus, most caps have an optional wire retainer that is supplied with these caps to lock the wires in place.

Product Features:
  • Designed w/Performance In Mind
  • High Quality Material
  • Stainless Terminals
  • Performance replacement part
See More

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)

Super Stock Replacement Coil for Improved Performance, Starting, and Power

from

$42.49
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:
  • 42000 Volts
  • Effective To 6500 RPM
  • Quicker Starting
  • Improved Throttle Response
  • Higher RPM Power
  • Can Finished In Yellow
See More

Energy Suspension – Axle Pivot Bushing Set (Part No.4.3121R)

Axle Pivot Bushing Set

from

$27.99
Product Features:
  • Firm in the Center Yet Soft on the Outside
  • Allows Flex and Pivot When Needed
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Competition Cams – Thumpr 227/241 Hydraulic Roller Cam (Part No.32-600-8)

Thumpr 227/241 Hydraulic Roller Cam

from

$522.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

289-302 Ford Head Bolt Kit

from

$107.99


Product Features:
  • Highest Quality Head Bolts
  • Cold-Formed/Heat Treated
  • Ensures Molecular Integrity
  • Reduced Diameter Bolt Heads
  • Hardened/Parallel-Ground Washers Included
  • Rated At 170000 psi
  • Manufactured By ARP
See More

Powertrax – Lock Right Locker (Part No.1821-LR)

Lock Right Locker

from

$441.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
  • Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
  • Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
  • Powertrax® = Extreme Traction Systems!
  • See More

    Proform – Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines (Part No.66969R)

    Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines

    from

    $228.99
    Fits Ford 289 – 302 (5.0). Utilizing the durable and dependable High Energy Ignition (HEI) system pioneered by GM, these distributors avoid the unsightly wiring of stock Ford electronic ignition systems by installing this one-piece distributor with an internally positioned coil and module. Easy to install: just connect one 12-volt hot wire to the distributor (has optional tach hook-up). These units offer calibrated advance curves that are optimized for maximum combustion efficiency and for the elimination of detonation damage and throttle ping. Assembled from precision-madeparts for advance curve smoothness. Offers longer term durability and a higher voltage spark that permits a bigger spark plug gap, resulting in more power and reduced plug fouling. Each unit includes a high-power coil, a premium hi-dielectric cap with brass terminals, and a low-saturation ignition module. By eliminating the stock-Ford ballast resistor, more ignition voltage results in improved spark. Incorporates easily found High Energy Ignition (HEI) replacement parts. Assembled with upper and lower bushings (stock Ford distributors have only a single bushing). Technical Note: Gear not compatible with roller cams. If using roller cams, please contact the cam manufacturer for proper gear selection.

    Product Features:
    • Street/Strip Version
    • Built-In Coil with Magnetic Trigger
    • Features Red Cap
    • Fits Ford 289-302 5.0 Engines
    • Comes with An Iron Gear and with Not Work with Factory Roller Cams
    See More

    Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.6683)

    Ultra Seal: Oil Pan Gasket

    from

    $59.19
    High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

    Product Features:
    • Steel core provides rigidity, durability and prevents gasket push out
    • Molded rubber coating seals minor irregularities in pan surface
    • One piece design is easier to install and even less prone to leak
    • Direct replacement suitable for all uses – street, racing, heavy duty
    • Include both gasket and new oil pan bolts
    • No Cork Particles
    • Easy Removal For Disassembly
    See More

    Edelbrock – Performer 460 Intake Manifold #2166 for Ford 429/460, Non-EGR, Satin Finish (Part No.2166)

    Performer 460 Intake Manifold #2166 for Ford 429/460, Non-EGR, Satin Finish

    from

    $397.99
    Product Features:
    • For Idle to 5500 RPM Street-Driven Performance
    • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
    • Patented Runner Design Ensures Broad Torque Curve
    • Excellent Throttle Response and Mid-Range Power
    • Accepts Late-Model Choke; Waterneck; and HEI
    • Accepts A/C And Alternator
    • Accepts Exhaust Heated Chokes
    See More

    Spectre – Water Neck; Ford 429-460 (Part No.4734)

    Water Neck; Ford 429-460

    from

    $54.99
    Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

    Product Features:
    • Fits Ford 429 – 460 engines
    • Has a 3/8 inch NPT threaded hole for temperature sensor
    • Includes sealing O-ring
    • Chrome plated
    • Easy to install
    • Hardware not included
    See More

    Upgrade your 1994 Ford E-250 Econoline with Top-Quality Performance and Racing Products

    When it comes to maintaining or upgrading your 1994 Ford E-250 Econoline, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Performance and Racing Products are key to keeping your E-250 Econoline functioning at its best. At Advance Auto Parts, we offer a wide selection of 71 Performance and Racing Products for the 1994 Ford E-250 Econoline, designed to meet your needs without breaking the bank. From Performance Oil Filter replacements to Performance Exhaust Products upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

    Affordable Prices and Wide Selection

    Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1994 Ford E-250 Econoline at great prices. Our Performance and Racing Products inventory for this model ranges from just $9.99 to $1,035.99, with an average price of $249.25. Our 71 Performance and Racing Products in stock come from 12 trusted brands, so you’re sure to find the right part for your 1994 Ford E-250 Econoline without overspending.

    Top Brands and High Customer Satisfaction

    Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1994 Ford E-250 Econoline, we stock popular OEM and aftermarket Performance and Racing Products from top names like Mr. Gasket, FEL-PRO Performance, Accel, and more. Mr. Gasket Performance and Racing Products start at just $19.99 and boast an impressive 4 stars average rating from customers. FEL-PRO Performance and Accel also bring quality to the table, with Performance and Racing Products available starting at $32.49, and at an average 4 stars rating. With 356 customer reviews and counting, our 1994 Ford E-250 Econoline Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

    Explore Related Parts and More

    While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1994 Ford E-250 Econoline is always ready to roll. We’re committed to providing you with everything you need to keep your E-250 Econoline in top shape, all in one place. Start shopping confidently below for your 1994 Ford E-250 Econoline!

    Best-Selling Performance Oil Filters for 1994 Ford E-250 Econolines

    Enhance the driving experience in your Ford with 1 quality Performance Oil Filter components, starting at $97.99.

    Mr. Gasket – Remote Oil Filter Kit (Part No.7682)

    Remote Oil Filter Kit

    from

    $97.99
    This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

    Product Features:
    • Relocate oil filter to an easy access location
    See More

    Most Popular 1994 Ford E-250 Econoline Performance Exhaust Products

    Customize your Ford with 4 Performance Exhaust Products products like Performance Exhaust Manifold Gaskets, all priced under $45.99.

    Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5928)

    Ultra Seal: Exhaust Gasket Set

    from

    $38.59
    Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

    Product Features:
    • Manufactured from high-temperature steel core/graphite faced exhaust material
    • Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
    • Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
    • Conforms to and seals minor surface irregularities
    • Can be trimmed if necessary for modified port applications
    • For OE replacement, high performance street, drag race and oval track use
    • Anti-Stick Properties
    • Easy Removal For Disassembly
    See More

    FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1467)

    Exhaust Manifold Gasket Set

    from

    $45.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
    • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
    • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
    • Slotted bolt holes allow for easier header installation.
    • Not intended for use in emission controlled vehicles.
    See More

    Mr. Gasket – Exhaust Gasket Set (Part No.264G)

    Exhaust Gasket Set

    from

    $36.49
    Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

    Product Features:
    • Manufactured from high-temperature acrylic blend exhaust material
    • Provides excellent sealing and durability
    • Can be trimmed if necessary for modified port applications
    • For OE replacement, high performance street, drag race and oval track use
    • Precision Die Cut For Excellent Fit
    See More

    FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1468)

    Exhaust Manifold Gasket Set

    from

    $45.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
    • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
    • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
    • Slotted bolt holes allow for easier header installation.
    • Not intended for use in emission controlled vehicles.
    See More

    Top Picks for 1994 Ford E-250 Econoline Performance Ignition Products

    Upgrade Ford E-250 Econolines with top-quality Performance Ignition Products parts, including 7 OEM and aftermarket selections for your 1994 model.

    Mallory – Unilite Ignition Module (Part No.605)

    Unilite Ignition Module

    from

    $85.29
    Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

    Product Features:
    • Service Part
    • No Moving Parts To Wear Out
    • Self Contained Unit
    • Can Drive OEM
    • Can Drive High Performance Ignition Coils
    See More

    Accel – Ford 1984-98 Eec-Iv Supercoil (Part No.140012)

    Ford 1984-98 Eec-Iv Supercoil

    from

    $77.99
    Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, and crisper throttle response. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

    Product Features:
    • Direct Plug In Replacement Direct OE Fit
    • Advanced Bobbin Technology
    • Standard Motor Products SMP Fd-478
    • MSD 5527
    • Standard Motor Products SMP Fd-478
    • MSD 5527
    • Resists Shock And Vibration
    • Resists Corrosion
    See More

    MSD Ignition – Coil; Street Fire; Ford TFI (Part No.5527)

    Coil; Street Fire; Ford TFI

    from

    $65.99
    These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

    Product Features:
    • Bolt-on Performance
    • Factory replacement coil
    See More

    Accel – Ford Tfi Modulator 1983-96 (Part No.35368)

    Ford Tfi Modulator 1983-96

    from

    $96.99
    This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most Ford Thick Film Ignition systems. 1983 thru 1996.

    Product Features:
    • Fits Most Stock And Modified Distributors
    • Dwell Control Circuit
    • Resists False Triggering
    See More

    Mallory – Distributor Wiring Harness (Part No.29349)

    Distributor Wiring Harness

    from

    $30.49


    Product Features:
    • Service Part
    • Makes Connections Quick And Easy
    See More

    MSD Ignition – Crank Trigger Kit; Big Block Ford (Part No.8644)

    Crank Trigger Kit; Big Block Ford

    from

    $538.99
    For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

    Product Features:
    • Absolutely the most accurate way to trigger the ignition
    • The non-magnetic pickup cannot be false triggered.
    • Powerful magnets are embedded in a billet aluminum trigger wheel.
    • Incl. brackets/mounting hardware to fit a variety of engines
    See More

    Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

    Promaster Classic Series; Ignition Coil

    from

    $186.99
    Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

    Product Features:
    • Glass Filled Polyester Case
    • Longer Spark Duration
    • Increased Performance
    • No Energy Loss Due To Arcing
    • Includes Brass Contact Terminal
    See More

    In-Demand Performance Distributors for 1994 Ford E-250 Econolines

    Select from 11 premium Performance Distributors parts for your 1994 Ford E-250 Econoline, with prices ranging from $52.99 to $691.99.

    Accel – Distributor Cap And Rotor Kit (Part No.8230)

    Distributor Cap And Rotor Kit

    from

    $108.99


    Product Features:
    • Heavy Duty Cap and Rotor Kit
    • With Brass Inserts
    See More

    MSD Ignition – Distributor Cap; Ford HEI (Part No.8408)

    Distributor Cap; Ford HEI

    from

    $52.99
    MSD molds our most popular V8 distributor caps in-house. These caps are injection molded from DuPont? Rynite material and feature spark plug-style terminals. These terminals offer improved locking connections and the Rynite material is extremely strong with excellent dielectric properties. Plus, most caps have an optional wire retainer that is supplied with these caps to lock the wires in place.

    Product Features:
    • Designed w/Performance In Mind
    • High Quality Material
    • Stainless Terminals
    • Performance replacement part
    See More

    Accel – High-Performance Distributor Cap & Rotor Kit (Part No.8233)

    High-Performance Distributor Cap & Rotor Kit

    from

    $53.09
    ACCEL cap and rotor kits offer superior protection from “arc-thru” and crossfire. Features 60k V-rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts and steel rotor springs provide for high spark energy flow.

    Product Features:
    • Features Protection From Arc Thru And Crossfire
    • Features 60k V Rated Alkyd Compound
    • Brass Terminals Inserts And Steel Rotor Springs
    • High Spark Energy Flow
    See More

    Accel – Tst Ford 84-97 5.8L 85-88 5.0L (Part No.TST15)

    Tst Ford 84-97 5.8L 85-88 5.0L

    from

    $230.99
    Everything you need to Super Tune Up your truck, van, or Jeep engine! The kits includes a high performance cap and rotor. A set of 8mm Extreme 9000 Spiral Core wires. This kit also includes the ACCEL classic copper core spark plugs to fire your engine up.

    Product Features:
    • Includes Everything Needed
    • Resistance High Dielectric Strength Compounds
    • Race Proven
    • Improved Performance
    • Reduced Emissions
    See More

    MSD Ignition – Distributor; Ford 351W; Ready-to-Run; with Steel Gear (Part No.83541)

    Distributor; Ford 351W; Ready-to-Run; with Steel Gear

    from

    $691.99
    MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky Duraspark systems or ancient breaker point models. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs. Plus, there is a vacuum advance canister to increase economy on long drives.

    Product Features:
    • Equipped w/Steel Gear
    • CARB E.O. Approved
    • Does not require an MSD Ignition Control
    • Supplied w/small dia. cap w/HEI style terminals; race and rotor
    • Will accept PN[8441] Cap-A-Dapt
    • Nylon pads ensure smooth operation of the advance weights
    • Advance weight pins are staked and tig welded to the plate
    • Mech. advance assem. can be locked out for crank trigger systems
    See More

    MSD Ignition – Distributor; Ford 351W; Vacuum Advance (Part No.8478)

    Distributor; Ford 351W; Vacuum Advance

    from

    $653.99
    The street pro-billet distributors are the perfect choice for powerful engines that see plenty of street time. The street models share the same features as the small diameter models shown above, plus feature a vacuum advance. This canister provides improved economy and an accurate mechanical advance lets you dial-in an advance curve to match your driving needs. A magnetic pick-up produces accurate trigger signals that remain stable throughout the entire rpm range of your engine and is completely maintenance-free.

    Product Features:
    • Billet housing 5/8 in. smaller dia. than stock Ford distributors
    • CARB E.O. Approved
    • Easy-to-adjust mech. advance w/supplied springs and stop bushings
    • Vacuum advance canister for improved economy (can be locked out)
    • CNC machined billet aluminum housing and billet aluminum base
    • Maintenance-free magnetic pickup and precision reluctor
    • Creates stable trigger signals throughout the rpm range
    • QPQ coated polished steel shaft; guided by sealed ball bearings
    • Advance plate and weights are fine blanked from chrome moly steel
    • QPQ coated for friction reduction
    • Mech. advance assem. can be locked out for crank trigger systems
    • Advance weight pins are staked and tig welded to the plate
    See More

    MSD Ignition – Distributor; Ford TFI; 351W (Part No.8453)

    Distributor; Ford TFI; 351W

    from

    $593.99
    When you start making serious power with your EFI Ford, the stock distributor shaft is one of the weak links of the engine. These Pro-Billet models answer the need for an affordable replacement in a strong and great looking package. Each distributor starts as a solid billet that is secured into a state of the art computer numerical control (CNC) machine where it is transformed into a precision housing. Inside each housing there is a sealed ball bearing at the top of the shaft. This design is responsible for accurately guiding the oversized polished steel shaft throughout the entire RPM range of your engine. The shaft is also quip-coated for friction reduction and corrosion resistance. The Pro-Billet distributors use a stock-style trigger pick-up to accept factory connectors. For installation, you simply remove the stock distributor and bolt the Pro-Billet MSD in place! Each model is supplied with a special gear to work with the?factory camshafts.

    Product Features:
    • Drop in billet replacement for late model Ford TFI 5.8L dist.
    • Supplied w/steel gear to work w/factory roller camshafts
    • Factory style ignition module connector accepts factory wiring
    • CNC machined billet aluminum housing and billet aluminum base
    • QPQ coated polished steel shaft; guided by sealed ball bearings
    • Supplied w/Late Model Distributor Cap And Rotor
    • Legal to install in all 50 states
    See More

    MSD Ignition – Distributor; Ford 351W; Pro-Billet; Small Cap (Part No.8578)

    Distributor; Ford 351W; Pro-Billet; Small Cap

    from

    $489.99
    MSD engineers fit all of their high performance distributor experience into a special compact housing designed to be less obtrusive for Ford engines. The diameter of the special cap and housing are 5/8 inch smaller than stock Ford distributors providing extra room in front of the engine. The new MSD cap features spark plug style terminals and is firmly screwed down to the housing. The distributor relies on MSD’s race proven magnetic pick-up and precision reluctor to deliver accurate trigger signals to the MSD ignition throughout high rpm. The reluctor assembly is turned by a hardened steel shaft which rides in a sealed ball bearing for high rpm stability and endurance. Mounted to the top of this shaft is a fully adjustable mechanical advance assembly. The rate at which the chromoly assembly advances the timing is easily controlled by changing the supplied advance springs and stop bushing for total advance.

    Product Features:
    • Billet housing 5/8 in. smaller dia. than stock Ford distributors
    • Must Be Used w/An MSD Ignition Control
    • Supplied w/small dia. cap w/HEI style terminals; race and rotor
    • Will accept PN[8441] Cap-A-Dapt
    • Nylon pads ensure smooth operation of the advance weights
    • Advance weight pins are staked and tig welded to the plate
    • Mech. advance assem. can be locked out for crank trigger systems
    • Advance plate and weights are fine blanked from chrome moly steel
    See More

    MSD Ignition – Distributor; Ford 351W; with Edelbrock Victor Jr (Part No.85805)

    Distributor; Ford 351W; with Edelbrock Victor Jr

    from

    $483.99
    MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

    Product Features:
    • Same features as PN[8584]
    • Use w/Edelbrock Victor Jr. man. for add. clearance at water neck
    • No CARB Exemption Order Number
    • Maintenance-free magnetic pickup and precision reluctor create stable trigger signals throughout the RPM range
    • Polished steel shaft is QPQ coated and guided by two sealed ball bearings
    • Advance weight pins are staked and tig welded to the plate
    • Supplied with cap-a-dapt and rotor (accepts MSD socket style caps)
    • Must be used with an MSD Ignition control
    See More

    Mallory – Distributor Drive Gear (Part No.29432)

    Distributor Drive Gear

    from

    $103.99
    Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

    Product Features:
    • Replacement Distributor Gear
    See More

    Mallory – Distributor Drive Gear (Part No.29421PD)

    Distributor Drive Gear

    from

    $73.29
    Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

    Product Features:
    • Replacement Distributor Gear
    See More

    Most Sold 1994 Ford E-250 Econoline Performance Engines

    Explore our best-selling Ford parts for the 1994 E-250 Econoline among 30 OEM and aftermarket options starting from $19.99.

    FEL-PRO Performance – Lower Intake Manifold Gasket Set: 11 Piece Set (Part No.1250)

    Lower Intake Manifold Gasket Set: 11 Piece Set

    from

    $33.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
    • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
    • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
    • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
    • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
    See More

    FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1684)

    Engine Valve Cover Gasket Set

    from

    $46.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Rigid core, molded silicone rubber gaskets provide for ease of installation, and are great for on-again/off-again situations (like setting valve lash).
    • Features high-tech silicone material for long life, a solid steel core for strength and durability, and stainless steel compression limiters to prevent
    • Not intended for use in emission controlled vehicles.
    See More

    Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

    High Performance 180 Degree Thermostat for Increased Flow

    from

    $26.99
    Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

    Product Features:
    • Opens At 180 Degrees
    • Designed to Resist Large Variations of Coolant Pressure at High RPM
    • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
    • For High Performance Street, Drag Race, and Oval Track
    • Copper & Brass Construction – Resists Corrosion
    • High Flow
    See More

    FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-2)

    Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

    from

    $55.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
    • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
    • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
    • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
    • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
    See More

    Edelbrock – Intake Manifold Gasket for 1963-1996 Small-Block Fords (Part No.7220)

    Intake Manifold Gasket for 1963-1996 Small-Block Fords

    from

    $28.99


    Product Features:
    • Clean Positive Seal
    • Embossed Silicone Bead Surrounding The Port
    • Matched To Manifolds And Cylinder Heads
    See More

    Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

    289-302 Ford Head Bolt Kit

    from

    $107.99


    Product Features:
    • Highest Quality Head Bolts
    • Cold-Formed/Heat Treated
    • Ensures Molecular Integrity
    • Reduced Diameter Bolt Heads
    • Hardened/Parallel-Ground Washers Included
    • Rated At 170000 psi
    • Manufactured By ARP
    See More

    Mr. Gasket – Intake Manifold Bolts (Part No.958G)

    Intake Manifold Bolts

    from

    $19.99
    These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers

    Product Features:
    • Hex Head
    • Zinc Plated
    • Ideal For Minimal Space
    • 12-Point Head And Flange
    • Zinc Plated For Protection
    See More

    Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

    ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST

    from

    $237.99
    The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

    Product Features:
    • Cost effective aluminum construction provides superior strength to weight ratio
    • Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
    • Durable design increases valve lift while withstanding the rigors of moderate race use
    • Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
    See More

    Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

    Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

    from

    $111.99
    Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

    Product Features:
    • For Use With Cast Iron Heads
    • Springs Made of Highest Quality Spring Wire
    • Springs Precision Wound To Close Tolerances
    • Use with Original Equipment Heads Only
    See More

    Mr. Gasket – Precision Timing Tape (Part No.1594)

    Precision Timing Tape

    from

    $21.79
    Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

    Product Features:
    • 6 3¿8″ diameter
    • 6 3┐8″ diameter
    • 289-302-351 cu. in.
    • Increased Performance
    • Set Valve Lash At Proper Time
    See More

    Mr. Gasket – Water Neck (Part No.9713)

    Water Neck

    from

    $48.09
    Precision die cast, these water necks or thermostat housings are first polished to a high luster, then chrome plated. Comes with gasket and Allen head mounting bolts. Fits 1979-1997 Ford 5.0/5.8L V8s.

    Product Features:
    • Chrome Plated For Great Looks
    • Includes Gasket & Mounting Bolts
    See More

    FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1820)

    Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set

    from

    $32.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
    • With steel core to provide ultimate excellent blowout resistance.
    • Not intended for use in emission controlled vehicles.
    See More

    Mr. Gasket – Mls Head Gasket (Part No.3175G)

    Mls Head Gasket

    from

    $110.99
    Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use.

    Product Features:
    • Gasket bore – 4.030 inch: Compressed thickness – .040 inch
    • Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
    • Optimized sealing embossments seals extreme cylinder pressure
    • Provides excellent stability and reduces cylinder bore distortion.
    • Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
    • Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
    • For high-performance street, drag race and oval track use
    See More

    Edelbrock – Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" (Part No.60399)

    Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02"

    from

    $1035.99
    Product Features:
    • Complete Single For Flat Tappet
    • 60cc Combustion Chamber Volume
    • 170cc Intake/60cc Exhaust Runner Volume
    • 2.02 in. Intake/1.60 in. Exhaust Valve Diameter
    • 0.625 in. Deck Thickness
    See More

    Edelbrock – Performer Small-Block Ford 1.90" Cylinder Head Hydraulic Flat Tappet (Part No.60329)

    Performer Small-Block Ford 1.90" Cylinder Head Hydraulic Flat Tappet

    from

    $1035.99
    50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

    Product Features:
    • 50-State Street Legal Aluminum Cylinder Head
    • Out-of-the-Box Bolt-On Performance
    • Intake Valves Are For Use w/Stock Pistons
    See More

    Edelbrock – Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90" (Part No.60379)

    Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90"

    from

    $1035.99
    Product Features:
    • Capable of 300 plus horsepower when matched with the Edelbrock Performer Power Package
    • 1.90 in. intake valves are for use with stock pistons
    • Exhaust valve is 1.60 in.
    • 60cc combustion with 170cc intake port
    • Flat Tappet Camshaft Type
    See More

    Edelbrock – Performer Small-Block Ford 1.90 Cylinder Head Flat Tappet Springs, Polished (Part No.603219)

    Performer Small-Block Ford 1.90 Cylinder Head Flat Tappet Springs, Polished

    from

    $966.99
    50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

    Product Features:
    • 50-State Street Legal Aluminum Cylinder Head
    • Out-of-the-Box Bolt-On Performance
    • Hand-Blended Intake and Exhaust Bowls
    • CNC-Matched Intake/Exhaust Ports in Std Location
    • Thicker Deck Surfaces than Other Brands
    • Heli-Coils in Rocker Studs and Exhaust Bolt Holes
    See More

    Edelbrock – Performer Small-Block Ford 2.02" Cylinder Head Hydraulic Flat Tappet (Part No.60359)

    Performer Small-Block Ford 2.02" Cylinder Head Hydraulic Flat Tappet

    from

    $893.99
    Product Features:
    • Made of aluminum with a natural finish
    • 60cc chambers with 170cc intake ports
    • 2.02 in. intake and 1.60 in. exhaust valves
    • Includes intake valves, exhaust valve, valve springs, retainers, locks, guide plate and valve stem seals
    • Does not include damper spring, rocker arms, nuts and drilled steam holes
    See More

    Edelbrock – RPM Air-Gap Small Block Ford Polished Intake Manifold (Part No.75811)

    RPM Air-Gap Small Block Ford Polished Intake Manifold

    from

    $772.99
    Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Improve performance on the street or race track. Larger cross-sectional area and taller card flange. Compatibility with lar

    Product Features:
    • Based on Performer RPM-Series with Unique Air Gap
    • Air Gap Cooler and Denser Mixture for More Power
    • Designed For 1500 To 6500 RPM
    • Designed For Street And High Performance
    • Larger Cross Sectional Area
    • Taller Carb Flange
    • Compatibility w/Large Displacement 351W Based Eng.
    See More

    Edelbrock – Engine Cylinder Head (Part No.60319)

    Engine Cylinder Head

    from

    $692.99
    50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

    Product Features:
    • 50-State Street Legal Aluminum Cylinder Head
    • Out-of-the-Box Bolt-On Performance
    • Intake Valves Are For Use w/Stock Pistons
    See More

    Edelbrock – Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" Bare (Part No.60389)

    Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" Bare

    from

    $594.99


    Product Features:
    • 50-State Street Legal Aluminum Cylinder Head
    • Out-of-the-Box Bolt-On Performance
    • Hand-Blended Intake and Exhaust Bowls
    • CNC-Matched Intake/Exhaust Ports in Std Location
    • Thicker Deck Surfaces than Other Brands
    See More

    Edelbrock – RPM Air-Gap Small Block Ford 351W Intake Manifold (Part No.7581)

    RPM Air-Gap Small Block Ford 351W Intake Manifold

    from

    $468.99
    Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Improve performance on the street or race track. Larger cross-sectional area and taller card flange. Compatibility with large displacement 351W based engines. For 4 bbl carbs. Available in cast, polished and endurashine finish.

    Product Features:
    • Based on Performer RPM-Series with Unique Air Gap
    • Air Gap Cooler and Denser Mixture for More Power
    • Designed For 1500 To 6500 RPM
    • Designed For Street And High Performance
    • Larger Cross Sectional Area
    • Taller Carb Flange
    • Compatibility w/Large Displacement 351W Based Eng.
    See More

    Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud (Part No.19043-16)

    Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud

    from

    $427.99
    These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Ford V8 289-302-351W applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

    Product Features:
    • CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
    • Designed for high performance street and race engines
    • Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
    • Additional clearance, up to 1.650″ O.D. valve spring
    See More

    Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam and Lifter Kit (Part No.CL35-250-4)

    Xtreme Energy 240/246 Hydraulic Flat Cam and Lifter Kit

    from

    $373.99
    Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

    Product Features:
    • Excellent performance in street carbureted applications.
    • More vacuum allows an increase in duration for improved performance and assists power brakes.
    • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
    • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
    See More

    Edelbrock – Performer-Plus camshaft for Small-Block Ford 351W V-8 applications (Part No.2182)

    Performer-Plus camshaft for Small-Block Ford 351W V-8 applications

    from

    $339.99


    Product Features:
    • Designed for Optimum Torque and Acceleration
    • Maximum Performance From Idle through Mid-Range
    • Matched to Edelbrock Performer Intakes
    • Includes Hydraulic Lifters and Assembly Lube
    • Major Improvement in Throttle Response and Torque
    • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
    • Take The Guesswork Out Of Camshaft Selection
    See More

    Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam (Part No.35-250-4)

    Xtreme Energy 240/246 Hydraulic Flat Cam

    from

    $284.99
    Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

    Product Features:
    • Excellent performance in street carbureted applications.
    • More vacuum allows an increase in duration for improved performance and assists power brakes.
    • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
    • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
    See More

    Edelbrock – Pushrod Set for Ford 351W (Part No.9659)

    Pushrod Set for Ford 351W

    from

    $190.99
    Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

    Product Features:
    • 7.7 in. Length
    • 0.312 in. Diameter
    • 4130 Chromoly Steel Material
    • Black Oxide Finish
    • Made In The USA
    See More

    Edelbrock – Sure Seat Valve Springs for Ford 351W V8 (Part No.5982)

    Sure Seat Valve Springs for Ford 351W V8

    from

    $44.99
    Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

    Product Features:
    • For Use With Cast Iron Heads
    • Springs Made of Highest Quality Spring Wire
    • Springs Precision Wound To Close Tolerances
    • Use with Original Equipment Heads Only
    See More

    Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

    Super Intake Manifold Bolts

    from

    $43.99
    Super Intake Manifold Bolts

    Edelbrock – TIMING CHAIN (Part No.7844)

    TIMING CHAIN

    from

    $29.99
    Product Features:
    • Timing Chain Only
    See More

    Top-Rated Performance and Racing Products Brands For Your 1994 Ford E-250 Econoline

    Shop for the best-rated brands offering Performance and Racing Products and other products for your 1994 Ford E-250 Econolines. Below you’ll find some of our best rated Performance and Racing Products from Mr. Gasket, FEL-PRO Performance, and Accel, and more. Performance and Racing Products from these brands that fit a 1994 E-250 Econoline start at just $19.99 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

    Popular Mr. Gasket 1994 Ford E-250 Econoline Performance and Racing Products

    When it comes to maintaining or upgrading your 1994 Ford E-250 Econoline, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Mr. Gasket ticks all of those boxes. We offer a wide selection of Mr. Gasket Performance and Racing Products, specifically designed for the 1994 Ford E-250 Econoline. With over 11 Mr. Gasket brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $19.99, with an average price of just $49.77. Plus, with over 23 customer reviews and an average rating of 4 stars, you can trust that our Mr. Gasket Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

    Ultra Seal: Exhaust Gasket Set
    from
    $38.59
    This product is not rated

    Ultra Seal: Exhaust Gasket Set

    “”

    Precision Timing Tape
    from
    $21.79
    This product is not rated

    Precision Timing Tape

    “”

    Remote Oil Filter Kit
    from
    $97.99
    This product is not rated

    Remote Oil Filter Kit

    “”

    Popular FEL-PRO Performance 1994 Ford E-250 Econoline Performance and Racing Products

    FEL-PRO Performance auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1994 Ford E-250 Econoline owner should feel confident when installing genuine FEL-PRO Performance parts in their vehicle. To ensure the best fit and performance for your 1994 E-250 Econoline, Advance Auto Parts carries a full inventory of 6 FEL-PRO Performance Performance and Racing Products. Plus you will be keeping your Ford in peak condition while saving money because prices on these FEL-PRO Performance Performance and Racing Products range from $32.49 to $55.99, plus, with more than 7 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

    Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set
    from
    $32.49
    This product is not rated

    Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set

    “”

    Exhaust Manifold Gasket Set
    from
    $45.99
    This product is not rated

    Exhaust Manifold Gasket Set

    “”

    Exhaust Manifold Gasket Set
    from
    $45.99
    This product is not rated

    Exhaust Manifold Gasket Set

    “”

    FAQs for 1994 Ford E-250 Econoline Performance and Racing Products

    Which Performance and Racing Products are best-sellers for 1994 Ford E-250 Econolines?

    Out of 71 Performance and Racing Products that fit 1994 Ford E-250 Econolines, the following parts are the top sellers:

    What’s the price range for 1994 Ford E-250 Econoline Performance and Racing Products?

    Performance and Racing Product prices for the 1994 Ford E-250 Econoline start at $9.99 and go up to $1,035.99 for the most premium parts.

    What’s the average price of a Performance and Racing Product for a 1994 Ford E-250 Econoline?

    The average price for Performance and Racing Products for the 1994 Ford E-250 Econoline is $249.25. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

    Does Advance Auto Parts sell Performance and Racing Products for other Ford E-250 Econoline model years?

    Yes, we currently carry Performance and Racing Products for 31 model years of Ford E-250 Econolines between 1975 and 2006. Performance and Racing Products are bought most frequently for the following model years: 2006, 2005, 2004, 2003, 2002, 2001, 2000, 1999, and 1998.

    What are the cheapest Performance and Racing Products for my 1994 Ford E-250 Econoline?

    The cheapest 1994 Ford E-250 Econoline Performance and Racing Products we carry in stock are:

    What types of Performance and Racing Products do you sell for my 1994 Ford E-250 Econoline?

    As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1994 Ford E-250 Econoline:

    Can I get help with 1994 Ford E-250 Econoline Performance and Racing Product orders?

    Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Performance and Racing Products and more.

    What is your return policy for Ford E-250 Econoline Performance and Racing Products?

    Advance Auto Parts keeps returns simple. For new Ford E-250 Econoline Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.