1993 GMC G2500 Performance Engines

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:

• 7.25 in. Length
• 0.312 in. Diameter
• 4130 Chromoly Steel Material
• Black Oxide Finish
• Made In The USA

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
• Not intended for use in emission controlled vehicles.

Secure the harmonic balancer or dampener on your Chevy. Works on original equipment, high performance street, drag or circle track applications. Features a heat treated black oxide coated Grade 8 alloy steel bolt for strength with a tall hex head to prevent wrench from slipping. An extra thick parallel ground washer provides accurate, uniform torque, and a lock washer is also included.

Product Features:

• Heat treated black oxide coated Grade 8 alloy steel
• Tall hex head bolt to prevent wrench from slipping
• Extra thick parallel ground washer provides accurate, uniform torque
• Washers Provides More Accurate And Uniform Torque
• Grade 8 Alloy Steel

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Edelbrock part #7209 Intake Gaskets for 1985-1995, Chevy V6 200-229-262 (3.8 and 4.3L) allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-

Product Features:

• 1.28″x2.10″
• Stock Port Style
• .060″ Thick
• Multi Piece Configuration
• Composite Material

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Die-cut for an excellent fit
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

• Twisted Snout Water Pump Design For Updated Style
• Street Performance
• Heavy Duty Shaft w/5/8 in. Pilot
• Six-Blade Stamped Steel
• Anti-Cavitation Impeller
• 100 Percent Leak Tested

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Product Features:

• Polished Version Of Edelbrock PN[2701]
• Polish is Hand-Buffed for Brilliant Shine
• Maximizes Performance with Edelbrock Carburetors
• Maximizes Peak Torque Around 3500 RPM
• Excellent Throttle Response and Mid-Range Power
• Prod. +5 HP and +9 ft/lbs. of Torque Over PN[2101]
• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• All Factory Connections Used
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal with OEM Throttle Body
• For OE and Small Bore TBI Injectors Only
• No Chip Changes/Computer Modifications Required
• 5.7L Power Package Provides Free Computer Chip

Holeshot 2400 for GM 1998 to 2002 4L60E Camaro and Firebird with an LS1 engine Application: GM 1998 to 2002 4L60E Camaro and Firebird with LS1 A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benef

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 195 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

• Features 12-point Smaller-than-standard Bolt Head
• Thick Flat Washers Distribute Optimum Clamp Load
• Ideal Use Where Space Is Minimal On Race Manifolds
• Bolts And Washers Zinc Plated For Protection
• Zinc Plated For Protection

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

• Manufactured from high-density cork/rubber blend gasket material
• Provides excellent sealing and durability
• For OE replacement, high performance street, drag race and oval track use

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Steel core gasket construction
• Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
• Not intended for use in emission controlled vehicles.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

• Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
• Best with aftermarket converters and more rear gear.
• Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts, the Xtreme Energy grind family offers gains in torque and horsepower while still delivering adequate vacuum for power brakes and other vacuum dependent accessories. Xtreme Energy camshafts work great in carbureted applications, but offer the best performance with aftermarket intake manifolds, lower gear ratios, headers and free flowing exhaust.

Product Features:

• HYDRAULIC – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.
• 249/260 Advertised Duration, 206/212 Duration @ .050″, .434″/.444″ Lift, 112 Lobe Separation
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.

Product Features:

• HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.
• 260/260 Advertised Duration, 212/212 Duration @ .050″, .440″/.440″ Lift, 110 Lobe Separation
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.