1993 Ford E-150 Econoline Drivetrains

Below you will find various in-demand Ford Drivetrains, components and accessories for your 1993 E-150 Econoline. Advance Auto Parts has popular E-150 Econoline parts like Drive Shafts and Axles, Transfer Cases, Spindles and more. You’ll also find aftermarket and OEM Drivetrains for other E-150 Econoline model years including 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2006 and more. Select a category of 1993 Ford E-150 Econoline Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1993 Ford E-150 Econoline Drivetrains Categories

Differential Oil

Differential Pinion Yokes

Drive Shaft Support Bolts

U-Joints

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Covers

Center Support Bearings

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Differential Bearings

Differential Axle Shafts

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Differential Cover Bolts

Axle Shaft Bearings

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Disc Kits

Differential Clutch Packs

Differential Mini Spools

Differential Ring and Pinions

U-Joint U-Bolt Kits

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Differential Spools

Differential Carrier Bearings

Differential Lock Springs

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Pinion Shafts

Differential Carrier Bearing Shims

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Mounting Adapter Seals

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Axle Shaft Studs

Differential Drive Pinion Oil Deflectors

Spindle Washers

Differential Ring and Pinion Kits

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

Differential Pinion Bearing Spacers

Differential Bolts

Essential Drivetrains for 1993 Ford E-150 Econolines

from

$354.99

9.75″ Ford TA HD aluminum cover.

Product Features:

Fits Ford 9.75″
Aluminum girdle cover

from

$4.99

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$121.99

Yukon replacement yoke for Dana 30, 44, 50, and Dana 300 with 26 spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$29.99

Product Features:

Locking key/wedge
Fits Dana Spicer 60 and 70

from

$998.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

Fits Dana Spicer 44 with 30 spline axles
3.92 and up ratio only
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$125.99

Worn or damaged differential end yoke causing driveline Vibrations! This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$378.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Dana Spicer 44 with 19 spline axles
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$315.99

Yukon positraction internals for 8″ and 9″ Ford with 28 spline axles, in a 4-pinion design. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 9″ with Trac Loc positraction with 28 spline axles
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$6.99

Product Features:

Inner oil slinger for Dana Spicer 25, 27, 30, 44 and 50

from

$354.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits standard rotation Dana Spicer 44
8.50″ ring gear diameter
26 spline pinion
10 ring gear bolts
5.13 ratio

from

$16.99

9.75″ Ford C-Clip.

Product Features:

C-clip
Fits Ford 9.75″

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles
Quality materials – all components are built for reliable longevity and performance
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits HM89410 race
All steel construction

from

$27.99

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

from

$175.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9″ without aftermarket Daytona pinion support
Included are pinion bearings and races, pinion seal, pilot bearing , crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$389.99

Yukon Performance 2-3/16″ deck steel spool for 9″ Ford with 40 spline axles. Spool uses 2″ journal bearings (45 degree). Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″ with 40 spline axles
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$12.99

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

Roll pin for Dana Spicer 30 and Dana Spicer 44
0.235″ diameter

from

$45.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$157.99

Axle shaft damaged or bearings worn out. This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$34.49

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$20.99

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$8.99

Product Features:

Trac Loc spring for Ford 8″ and 9″

from

$98.99

Product Features:

MINI SPOOL 8.8 FORD 28SPL

from

$57.99

8.8″ Ford 7/8″ diameter Notched cross pin shaft (.875″ for ’86 and newer). This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers.

Product Features:

Notched cross pin shaft for Ford 8.8″
0.875″ diameter
Not compatible with Spartan Locker or Powertrax Lock Right

from

$46.99

Product Features:

USA Standard Gear heavy-duty cross pin shaft
Fits Dana Spicer 44
Works with Spartan Locker or standard open spider gears

Upgrade your 1993 Ford E-150 Econoline with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1993 Ford E-150 Econoline, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your E-150 Econoline functioning at its best. At Advance Auto Parts, we offer a wide selection of 237 Drivetrains for the 1993 Ford E-150 Econoline, designed to meet your needs without breaking the bank. From Drive Shafts and Axle replacements to Transfer Cases upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1993 Ford E-150 Econoline at great prices. Our Drivetrains inventory for this model ranges from just $1.29 to $2,199.99, with an average price of $298.62. Our 237 Drivetrains in stock come from 23 trusted brands, so you’re sure to find the right part for your 1993 Ford E-150 Econoline without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1993 Ford E-150 Econoline, we stock popular OEM and aftermarket Drivetrains from top names like National, Dorman, Motive Gear, and more. National Drivetrains start at just $11.99 and boast an impressive 4.3 stars average rating from customers. Dorman and Motive Gear also bring quality to the table, with Drivetrains available starting at $3.49, and at an average 4.2 stars rating. With 8,569 customer reviews and counting, our 1993 Ford E-150 Econoline Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1993 Ford E-150 Econoline is always ready to roll. We’re committed to providing you with everything you need to keep your E-150 Econoline in top shape, all in one place. Start shopping confidently below for your 1993 Ford E-150 Econoline!

Best-Selling Drive Shafts and Axles for 1993 Ford E-150 Econolines

Enhance the driving experience in your Ford with 18 quality Drive Shafts and Axle components, starting at $5.99.

show more show less

from

$6.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$22.49

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$40.99

Anchor 6038 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 In. / 40 mm
CENTERLINE: 2.48 In. / 63 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Not Pictured: Two Dust Shields

from

$11.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$44.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$21.99

Anchor 6056 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 In. / 35 mm
CENTERLINE: 2.28 In. / 58 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Complete Mount

from

$19.99

Value-priced bearing meets all cataloged application requirements.

from

$7.99

Wheel Lug Stud

from

$52.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1559TV axle bearing and seal kit, TorringtonBrand, 2.530″ OD, 1.620″ ID This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.530″ O.D.
1.620″ I.D.

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$6.99

Ford 7.5″, 8″, 8.8″, & 9″ axle stud.

Product Features:

Axle stud for Ford 7.5″, 8.8″ and 9″
1/2″ x 20 thread
1 7/8″ long
29/64″ shoulder length

from

$5.99

AXLE STUD , 58MM X M14-2.0 .

from

$7.99

Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.

Product Features:

Rear axle seal
2.530″ O.D.

from

$246.99

Yukon forged yoke for Ford 8.8″ with a 1350 U/joint size (stronger than billet). 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$64.99

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$55.99

The part you need. The name you trust. Spicer driveline components deliver top performance and value. These center bearing kits are manufactured to the same genuine standards you’ve come to expect from the most reliable name in driveshaft parts.

Product Features:

Dana manufactured Spicer center bearing kit
Interchangeable with OE component
Comes as a complete kit to replace, repair, or refurbish
Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace

from

$10.79

We develop and produce high-quality roller bearings, spherical bearings, and plain bearings worldwide for a wide range of applications.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$6.29

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Top Picks for 1993 Ford E-150 Econoline Spindles

Upgrade Ford E-150 Econolines with top-quality Spindles parts, including 6 OEM and aftermarket selections for your 1993 model.

show more show less

from

$3.49

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.49

This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.99

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$4.79

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$4.79

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$3.99

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

In-Demand Universal Joints for 1993 Ford E-150 Econolines

Select from 15 premium Universal Joints parts for your 1993 Ford E-150 Econoline, with prices ranging from $4.59 to $111.99.

show more show less

from

$42.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$34.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASEABLE DESIGN – Greaseable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$31.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$23.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$39.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$6.99

This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.89

Universal Joint

from

$4.59

Universal Joint

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$40.99

from

$61.99

Yukon 1330 Dual-size cap U/Joint. 3.625″ snap ring span. One set of caps is 1.125″ in diameter and the other is 1.062″. Outside snap ring.

from

$51.99

Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.

from

$111.99

Yukon 1350 to Mechanics 3R adaptor U/joint.

from

$37.99

from

$22.49

KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

Most Sold 1993 Ford E-150 Econoline Differentials

Explore our best-selling Ford parts for the 1993 E-150 Econoline among 194 OEM and aftermarket options starting from $1.29.

show more show less

from

$35.99

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life. Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$12.99

Valvoline High Performance Gear Oil is an extreme pressure gear lubricant formulated with quality base oils and superior additives that helps protect against severe temperatures, shock loads, scuffing, scouring, corrosion and pitting in high speed, high load, high torque and high horsepower conditions.

Product Features:

Formulated for reliable gear protection
Protects against severe temperatures to help extend service life
Formulated with extreme-pressure additives to minimize gear wear from shock loads
Helps protect against gear wear from scuffing, scouring, corrosion and pitting
Recommended for conventional hypoid differentials and non-synchronized manual transmissions in passenger cars, light trucks, sport utility vehicles, vans and heavy-duty trucks where an API-GL5 or GL-4 fluid is specified
PLEASE NOTE: Valvoline recommends SynPower Full Synthetic Gear Oil for limited slip differentials

from

$24.99

Max Gear is recommended for truck and automotive differentials, outboard motor lower units or in rear axles or manual transmissions requiring an API fluid. Max Gear is a high performance automotive gear oil designed to provide maximum protection to heavily loaded gears while increasing power throughput through the drive train. Max Gear virtually eliminates both gear and bearing wear-even under severe squeeze film conditions caused by extremely high loads, sudden shock loads or low RPMs. Slippery, synthetic molecules not only reduce wear and friction but significantly increase Max Gear’s cold weather fluidity and lubricity, making it the ideal choice for vehicles operating in cold climates. Gears run smoother, quieter, cooler and longer without overhauls. It is noncorrosive to both ferrous and nonferrous metals.

Product Features:

Maximizes horsepower
Extends gear and bearing life
Reduces operating temperature
Lower coefficient of friction
Superior corrosion protection
Separates rapidly from water
For use with open, limited-slip and locking differential
Contains limited-slip friction modifier
Made in USA

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$126.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT BRG&SL FORD MSTR 8.8

from

$179.99

Product Features:

FRD 10BL 8.8 R/P 4.10A MG

from

$15.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$41.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$95.99

Product Features:

FRD 8.8″ INT. KIT 31 SPL OPEN 1987 & LATER ONLY

from

$6.79

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$27.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$137.99

MASTER KIT FORD 8.8″

from

$6.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$169.99

The National bearing & seal kit includes all the components required to complete the repair.

Product Features:

COMPLETE SOLUTION – Includes everything needed to complete the repair
STRONG AND DURABLE – Controlled heat treatment process for strength and durability
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Professional technicians know they can depend on National

from

$129.99

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

AXLE SHAFT 8.8″ 31 SPL. R.H. 31 1/6″ O.A. 87-96

from

$48.99

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$116.99

The National bearing & seal kit includes all the components required to complete the repair.

Product Features:

COMPLETE SOLUTION – Includes everything needed to complete the repair
STRONG AND DURABLE – Controlled heat treatment process for strength and durability
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Professional technicians know they can depend on National

from

$8.99

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$37.99

DIFF COVER KIT

from

$123.99

Product Features:

CLUTCH PACK KIT 8.8″ FORD 1 KIT PER UNIT

from

$19.99

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations.
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$6.99

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

Top-Rated Drivetrains Brands For Your 1993 Ford E-150 Econoline

Shop for the best-rated brands offering Drivetrains and other products for your 1993 Ford E-150 Econolines. Below you’ll find some of our best rated Drivetrains from National, Dorman, and Motive Gear, and more. Drivetrains from these brands that fit a 1993 E-150 Econoline start at just $3.49 and are rated as high as 4.3 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular National 1993 Ford E-150 Econoline Drivetrains

When it comes to maintaining or upgrading your 1993 Ford E-150 Econoline, using quality Drivetrains is essential to ensure durability and a perfect fit. National ticks all of those boxes. We offer a wide selection of National Drivetrains, specifically designed for the 1993 Ford E-150 Econoline. With over 3 National brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $11.99, with an average price of just $21.99. Plus, with over 29 customer reviews and an average rating of 4.3 stars, you can trust that our National Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $37.99

(1)

Shaft Repair Sleeve

“Very delicate piece, but came shipped quite safely and not damaged. High quality.”

from $15.99

(9)

Bearing

“as advertised”

from $11.99

(19)

Multi-Purpose Seal

“Enough to do the job!!!”

Popular Dorman 1993 Ford E-150 Econoline Drivetrains

Dorman auto parts is one of the highest quality Drivetrain brands in the market. Any 1993 Ford E-150 Econoline owner should feel confident when installing genuine Dorman parts in their vehicle. To ensure the best fit and performance for your 1993 E-150 Econoline, Advance Auto Parts carries a full inventory of 3 Dorman Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these Dorman Drivetrains range from $3.49 to $22.49, plus, with more than 7 customer reviews and an impressive 4.2 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $3.49

(3)

Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In.

“Same as oem”

from $22.49

(1)

Driveshaft Flange Bolts

“This item appears to be correct and my review is more of a bashing of AA help desk who apparently does not answer questions as you are lead to believe”

from $5.49

(3)

Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm

“Fit just like the original.”

FAQs for 1993 Ford E-150 Econoline Drivetrains

Which Drivetrains are best-sellers for 1993 Ford E-150 Econolines?

Out of 237 Drivetrains that fit 1993 Ford E-150 Econolines, the following parts are the top sellers:

Greaseable Premium Universal Joint (10086740) – $34.99
Axle Housing Cover Gasket Rectangular Shaped, 10 Bolt Hole Gasket (5782406) – $15.99
Universal Joint (10265720) – $31.99

What’s the price range for 1993 Ford E-150 Econoline Drivetrains?

Drivetrain prices for the 1993 Ford E-150 Econoline start at $1.29 and go up to $2,199.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1993 Ford E-150 Econoline?

The average price for Drivetrains for the 1993 Ford E-150 Econoline is $298.62. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford E-150 Econoline model years?

Yes, we currently carry Drivetrains for 27 model years of Ford E-150 Econolines between 1975 and 2006. Drivetrains are bought most frequently for the following model years: 2006, 2002, 2001, 2000, 1999, 1998, 1997, 1996, and 1995.

What are the cheapest Drivetrains for my 1993 Ford E-150 Econoline?

The cheapest 1993 Ford E-150 Econoline Drivetrains we carry in stock are:

Differential Ring Gear Bolt (10282257) – $1.29
Ring Gear Bolt (20520509) – $1.99
Differential Crush Sleeve (10282338) – $2.99
Differential Cross Shaft (10282201) – $2.99
Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49

What are the top-rated Drivetrains that fit the 1993 Ford E-150 Econoline?

Out of 8,569 reviews by customers, our 1993 Ford E-150 Econoline Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1993 Ford E-150 Econoline and their top-rated products:

Universal Joints
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Non-Greaseable Super Strength Universal Joint (10087058) – $23.99
- Greaseable Premium Universal Joint (10086740) – $34.99
Differentials
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Non-Greaseable Super Strength Universal Joint (10087058) – $23.99
- Greaseable Premium Universal Joint (10086740) – $34.99
Spindles
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Non-Greaseable Super Strength Universal Joint (10087058) – $23.99
- Greaseable Premium Universal Joint (10086740) – $34.99

What types of Drivetrains do you sell for my 1993 Ford E-150 Econoline?

As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1993 Ford E-150 Econoline:

Can I get help with 1993 Ford E-150 Econoline Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford E-150 Econoline Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford E-150 Econoline Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1993 Ford E-150 Econoline Drivetrains

Yukon Gear – 9.75" Ford Ta HD Aluminum Cover (Part No.32115)

Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-019.1)

Yukon Gear – Cover Bolt For Ford 7.5", 8.8" & 9.75" (Part No.33554)

Yukon Gear – Replacement Yoke For Dana 30, 44, 50, And 300 With 26 Spline And A 1310 U/Joint Size (Part No.41018)

Yukon Gear – Locking Key / Wedge For Dana 60 & 70 Spindle Nut (Part No.33512)

Yukon Gear – Dana 44 Grizzly Locker Replacement (Part No.28001)

Dorman – Differential Pinion Yoke Assembly (Part No.697-539)

Dorman – Differential Yoke including Seal and Pinion Nut (Part No.697-507)

USA Standard Gear – Master Overhaul Kit for the Dana 44 Differential with 19 Spline (Part No.37084)

Yukon Gear – Positraction Internals For 8" And 9" Ford With 28 Spline Axles, In A 4-Pinion Design (Part No.16023)

Yukon Gear – Dana 25 / 27 / 30 / 44 / 50 Inner Oil Slinger Replacement (Part No.33012)

Yukon Gear – High Performance Replacement Ring & Pinion Gear Set For Dana 44 Standard Rotation, 5.13 Ratio (Part No.24042)

Yukon Gear – 9.75" Ford C-Clip (Part No.33248)

Dorman – Differential Clutch Kit (Part No.697-780)

Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)

Yukon Gear – Bearing Race Driver (Part No.56017)

Yukon Gear – Pinion Depth Shims For GM 8.25" IFS, 8.5", 12 Bolt Car, Ford 8.8" & Chrysler 8.25" (Part No.55009)

Yukon Gear – Pinion Install Kit For Ford 9" Differential (Part No.13042)

Yukon Gear – Steel Spool For Ford 9" With 40 Spline Axles (Part No.32182)

Yukon Gear – Dana 30 / 44 Roll Pin Replacement (Part No.33312)

Spicer – Universal Joint (Part No.5-7438X)

Dorman – Rear Axle Shaft (Part No.630-208A)

Schaeffler – Bearing – TRB (Tapered Roller Bearing) (Part No.KT36)

Schaeffler – Shaft Seal (Part No.SS2852)

Yukon Gear – Trac Loc Spring For Ford 9" & 8" (Part No.33518)

Motive Gear – Differential Mini Spool (Part No.MS88-28)

Yukon Gear – 8.8" Ford 7/8" Diameter Notched Cross Pin Shaft (.875" For ’86 And Newer) (Part No.33434)

USA Standard Gear – Spartan Locker Replacement Cross Pin For Dana 44 (Part No.17017)

Driveworks – Oil Seal (Part No.S-8835S)

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

National – Multi-Purpose Seal (Part No.8835S)

National – Drive Shaft Center Support Bearing (Part No.HB-88107-A)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

Driveworks – Ball Bearing (Part No.S-HB-88107-A)

Yukon Gear – Wheel Lug Stud (Part No.33571)

Yukon Gear – R1559Tv Rear Axle Bearing And Seal Kit (Part No.10001)

Yukon Gear – C/Clip (Part No.33083)

Yukon Gear – Ford 7.5", 8", 8.8", & 9" Axle Stud (Part No.33175)

Yukon Gear – Axle Stud , 58Mm X M14-2.0 (Part No.33557)

Yukon Gear – Axle Seal, For 1559 Or 6408 Bearing (Part No.30201)

Yukon Gear – Forged Yoke For Ford 8.8" With A 1350 U/Joint Size (Part No.41051)

Schaeffler – Bearing – CRB (Cylindrical Roller Bearing) (Part No.102549)

Spicer – Drive Shaft Center Support Bearing (Part No.211175X)

Schaeffler – Bearing – CRB (Cylindrical Roller Bearing) (Part No.FC67148.5)

Schaeffler – Shaft Seal (Part No.SS2698)

National – Bearing (Part No.M88048)

National – Shaft Repair Sleeve (Part No.99199)

Driveworks – Tapered Roller Bearing (Part No.S-M-802048)

Schaeffler – Cup (Part No.M88010)

Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (Part No.615-072.1)

Dorman – Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (Part No.615-073.1)

Dorman – Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (Sold by each) (Part No.615-073)

Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Sold by each) (Part No.618-033)

Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (sold by each) (Part No.615-072)

Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-033.1)

Spicer – Universal Joint, Greaseable 1330 Series OSR (Part No.5-213X)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354)

Driveworks – Universal Joint (Part No.DW-354)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)

Dorman – Help – U-Joint Bolt Kit (Part No.81004)

Neapco – Universal Joint (Part No.2-4801)

Neapco – Universal Joint (Part No.2-4800)

Driveworks – Universal Joint (Part No.DW-270)

Spicer – Universal Joint (Part No.5-1330X)

Yukon Gear – 1330 Dual-Size Cap U/Joint (Part No.42017)

Yukon Gear – 1350 U/Joint With Zerk Fitting (Part No.42010)

Yukon Gear – 1350 To Mechanics 3R Adaptor U/Joint (Part No.42001)

Spicer – Universal Joint (Part No.5-1330-1X)

MOOG Driveline Products – Universal Joint (Part No.444)

Valvoline – MaxLife Multi-Vehicle Automatic Transmission Fluid, 1 Gallon (Part No.773775)

Valvoline – High Performance Transmission & Differential Gear Oil: Conventional 80W-90, 1 Quart (Part No.VV831)

Royal Purple – MaxGear SAE 75W90 High Performance Gear Oil w/Friction Modifier Additive, 1 QT (Part No.01300)

Motive Gear – Differential Pinion Shim Kit (Part No.1100)

Motive Gear – Differential Master Bearing Kit – Koyo (Part No.R8.8RMK)

Motive Gear – Differential Ring and Pinion (Part No.F8.8-410A)

Felpro – Axle Housing Cover Gasket Rectangular Shaped, 10 Bolt Hole Gasket (Part No.RDS 55341)

Dorman – Differential Cover (Part No.697-702)