1993 Chevrolet K1500 Performance and Racing Products

Name: Cylinder Head Dowel Pins
Brand: Mr. Gasket
SKU: 4375
Price: 17.99 USD

Below you will find various in-demand Chevrolet Performance and Racing Products, components and accessories for your 1993 K1500. Advance Auto Parts has popular K1500 parts like Performance Exhaust Products, Performance Ignition Products, Performance Air Filters and more. You’ll also find aftermarket and OEM Performance and Racing Products for other K1500 model years including 1990, 1991, 1992, 1994, 1995, 1996, 1997, 1998, 1999 and more. Select a category of 1993 Chevrolet K1500 Performance and Racing Products below and start saving instantly.

Popular 1993 Chevrolet K1500 Performance and Racing Products Categories

Performance Oil Filters

Performance Engine Coolant Thermostats

Performance Starters

Performance Intake Manifolds

Performance Air Filters

Performance Coils

Performance Exhaust Mufflers

Performance Distributor Cap and Rotor Kits

Performance Exhaust Headers

Engine Cold Air Intakes

Performance Shifters

Performance Distributors

Performance Valve Covers

Performance Body Mounts

Performance Water Outlet Gaskets

Performance Engine Dress-Up Kits

Performance Engine and Transmission Mounts

Performance Engine Water Pumps

Performance Radiator Caps

Performance Engine Cylinder Head Gaskets

Performance Engine Camshaft and Lifter Kits

Performance Engine Harmonic Balancers

Performance Ignition Modules

Performance Distributor Components

Performance Clutch Pressure Plate and Disc Sets

Performance Engine Timing Sets and Components

Performance Engine Valve Springs

Performance Engine Valve Cover Gasket Sets

Performance Spark Plug Wires

Performance Chassis Bushing Kits

Performance Flywheel and Flexplates

Performance Exhaust Manifold Gaskets

Performance Posi Units and Components

Performance Oil Pans

Performance Timing Covers and Tabs

Performance Exhaust Tail Pipes

Performance Leaf Spring Bushings

Performance Ignition Kits

Performance Valve Cover Hardware

Performance Engine Rocker Arms

Performance Engine Camshafts

Performance Engine Oil Pan Gaskets

Performance Ring and Pinions

Performance Ignition Parts

Performance Exhaust Pipes

Performance Intake Manifold Hardware

Performance Lower Control Arm Bushings

Performance Engine Valve Lifters

Performance Sway Bar Bushings

Performance Engine Main Bearing Gasket Sets

Performance Brake Bleeders

Performance Tie Rod End Boots

Performance Oil Filler Caps

Performance Engine Push Rod Guideplates

Performance Engine Cylinder Head Installation Kits

Performance Engine Timing Cover Gasket Sets

Performance Engine Push Rods

Performance Engine Valve Spring Retainer

Performance Torque Converters

Performance Ignition Systems

Performance Nitrous Systems

Performance Engine Camshaft Bolts

Performance Engine Valve Stem Seal Sets

Essential Performance and Racing Products for 1993 Chevrolet K1500s

from

$17.99

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$458.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$121.99

Chrome plated steel valve covers with original equipment height and internal baffle. Features one breather/oil fill cap opening per valve cover. Sold as a pair. Hardware and gaskets sold separately.

Product Features:

Chrome plated steel construction
Center bolt design with ribbed top
Has two openings in one cover & one opening in the other
Includes rubber grommets and chrome oil filler cap
Sold as a pair
Has Ribs On The Top Of Each One

from

$149.99

The Super 40 features Flowmaster’s Delta Flow technology. It’s larger case profile provides the best of both worlds of performance and sound. The Super 40 has that deep powerful sound of the Original 40 series but with all the benefits of performance and low interior resonance from the Delta Flow technology. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$249.99

Everything you need to Super Tune Up your truck, van, or Jeep engine! The kits includes a high performance cap and rotor. A set of 8mm Extreme 9000 Spiral Core wires. This kit also includes the ACCEL classic copper core spark plugs to fire your engine up.

Product Features:

Complete Super Tune Kit
8mm Spiral Core Wires
Accel Classic Core Plugs
High Performance Cap And Rotor
Reduced Emissions

from

$75.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$367.99

K&N air intake systems are engineered for increased performance, outstanding durability, and sleek aesthetics – and are available in an assortment of finishes and powder coatings. K&N’s state-of-the-art High-Flow Air Filter helps to shield your engine from contaminants, while a meticulously engineered aerodynamic tube design contributes to a guaranteed increase in horsepower and torque. K&N air intake systems are designed to improve acceleration, towing, and throttle response while providing world class protection for your engine. Our intakes are dyno-tested and provide up to 50% more airflow compared to OEM intake systems. K&N intakes are easy to install and maintain with air filter cleaning required only every 100,000 miles.

Product Features:

GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
IMPROVED ENGINE SOUND: Hear the power under the hood.
WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
HIGH QUALITY: Made in America.

from

$305.99

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.

Product Features:

Cam and lifter kit for Small Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.
280/280 Advertised Duration, 230/230 Duration @ .050″, .480″/.480″ Lift, 110 Lobe Separation
Valve spring upgrade required

from

$185.99

RngPnn

from

$17.99

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.

Product Features:

Made from hi-performance 60 KV rated alkyd molding compound.
Cap and rotor kits include nylon rotor hold-down screws.
Flame-Thrower dust covers provide a larger air gap around the coil.

from

$91.99

Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features:

Made of Superior Hyper-Flex+ Material
Adds Dramatic Amount of Performance/Durability
Helps Vehicle Be in Control
Allows the Suspension to Function Properly

from

$349.99

Product Features:

Bolt On Quickly And Easily
Top Performance/Clean Machine
Increased Efficiency
Leak Free Seal
Connects To Exhaust Head Pipe
Complete With Premium Gaskets
16-Gauge Tubing For Durability

from

$49.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$31.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$9.99

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
3/8 inch-16 by 1 inch bolts
Kit includes 12 bolts and washers
Manufactured from high quality steel
Bolts feature hex heads

from

$18.99

Chrome-plated for beauty and durability, wing bolts make valve cover removal fast & easy. They are precision-engineered and feature extra-long threads to accommodate Mr. Gasket re-usable valve cover gasket & custom valve covers.

Product Features:

Fits Chevy V8
Standard Y Top 1/4 In-20 X 5/8 in L
Chrome Plated Steel
Overall Length: 4.64″
Installed Length: 4.00″
Pack of 4

from

$111.99

Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use.

Product Features:

Gasket bore – 4.060″ Thickness – .040″
Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
Optimized sealing embossments seals extreme cylinder pressure
Provides excellent stability and reduces cylinder bore distortion.
Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
For high-performance street, drag race and oval track use

from

$435.99

The street Pro-Billet is a popular route for people looking for proven race performance for their street cars. A vacuum advance canister provides economy and the proven MSD mechanical advance gives you the opportunity to dial-in a timing curve to fit your needs. Inside, an oversized steel shaft is QPQ coated for low friction and rides in a sealed ball bearing at the top of the distributor with an extra-long sintered bushing at the bottom. This combination keeps the shaft steady creating accurate spark delivery at any RPM. The street Pro-Billet relies on a magnetic pick-up to trigger the MSD Ignition control which delivers the powerful sparks to the coil. This pick-up is extremely accurate and never needs adjusting.

Product Features:

Designed for street/performance use w/mechanical or vacuum adv.
Must Be Used w/An MSD Ignition Control
Supplied w/An HEI Style Distributor Cap And Rotor
Accepts Cap-A-Dapts
O-ring seals can be installed for oil press. control (Mods only)
Special oil tract improves lubrication to the dist./cam gear
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate

from

$899.99

Torque Converter – Traveler Converter with 2000 RPM Stall Speed APPLICATION: GM 4L80E The Traveler converter is intended for use in motorhomes, tow vehicles or other heavy duty applications where a slightly higher stall speed is helpful in getting the vehicle moving. The Traveler is also stronger than a stock converter and has been internally modified to provide about 300 rpm more stall speed for help in initial acceleration without sacrificing normal highway operation. It is manufactured to B&M’s exacting tolerances for long life. Provides slightly higher stall speed than stock to improve pulling power at low speeds. Application: GM 4L80E Please download the attached 4L80E torque converter installation tips. New Precision pump drive tube Heavy duty needle bearings Furnace brazed New sprag and rollers in stator Pressure tested Fully balanced.

Product Features:

Ideal For Motor Homes
Ideal For Towing Applications
Precision Pump Drive Tube
Heavy Duty Needle Bearings
Furnace Brazed
New Sprag and Rollers In Stator
Pressure Tested
Fully Balanced

from

$143.99

Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:

Assures Longer Lasting Cab to Bed Alignment
Replace to Restore Ride Height
Gain Durability
Stronger Than Original Rubber Mounts

from

$21.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Steel core gasket construction
Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
Not intended for use in emission controlled vehicles.

from

$10.79

Spectre’s Oil Filler Cap is engineered to provide high quality replacement hardware for General Motors cars made in 1987 or later. Featuring a triple chrome-plated finish, this screw-in cap is manufactured using plastic.

Product Features:

Fits General Motors cars from 1987 and later
Features a triple chrome-plated finish
Manufactured from plastic material
OEM replacement part

from

$34.99

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Withstands Intense Exhaust Heat
Graphite-Impregnated Facing
Steel Expanded Metal Core
Superior Tensile Strength
Resists Deteriorating
Anti-stick Properties
Easy Removal For Disassembly

from

$41.49

Spectre’s High Performance Replacement Air Filters are engineered to outperform ordinary paper filters by providing increased air flow for improved performance. Manufactured using high quality materials including pre-dyed synthetic media, urethane, and steel mesh, this performance air filter is factory pre-oiled and ready to use. Use a Spectre Accucharge cleaning and re-oiling kit, part number HPR4820, to maintain your filter’s condition.

Product Features:

Designed to be superior to stock paper filters
Comes pre-oiled
Designed for an easy installation with OE fit
Made with pre-dyed media for lasting color

from

$20.99

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

Ideal For Tight Spaces
Serrations Prevent Loosening
Flange Distributes Pressure
Zinc Plated Bolts
Grade 5 Material
Easy Installation

from

$12.99

Installs using stock timing cover bolts. Chrome plated steel is a much better compliment to a chromed timing cover.

Product Features:

Bolts on with existing timing cover bolts
Chrome plated steel is a much better compliment for chrome timing covers
Balancer

from

$10.99

Installs using stock timing cover bolts. Chrome plated steel is a much better compliment to a chromed timing cover. Has markings for 16 degrees before top dead center (BTDC) to 8 degrees after top dead center (ATDC).

Product Features:

Bolts on with existing timing cover bolts
Chrome plated steel is a much better compliment for chrome timing covers
Markings for 16 degrees BTDC to 8 degrees ATDC

from

$24.99

Bolts on with existing timing cover bolts. It is chrome plated steel, which makes is a better compliment to a chrome timing cover. It also has an adjustable red timing pointer. This allows for better visibility and helps you set your timing more easily. Just loosen the screw, set the pointer to the desired initial timing level, and screw it back down. Then you’ll be able to more clearly see if your timing is where you want it when checking your timing. Has markings from 12 degrees before top dead center (BTDC) to 8 degrees after top dead center (ATDC).

Product Features:

Bolts on using existing timing cover bolts
Chrome finish compliments chrome timing covers
Red adjustable pointer makes it easier to check timing
Timing marks from 12 degrees BTDC to 8 degrees ATDC

Upgrade your 1993 Chevrolet K1500 with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1993 Chevrolet K1500, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Performance and Racing Products are key to keeping your K1500 functioning at its best. At Advance Auto Parts, we offer a wide selection of 353 Performance and Racing Products for the 1993 Chevrolet K1500, designed to meet your needs without breaking the bank. From Performance Exhaust Product replacements to Performance Ignition Products upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1993 Chevrolet K1500 at great prices. Our Performance and Racing Products inventory for this model ranges from just $7.99 to $1,712.00, with an average price of $270.54. Our 353 Performance and Racing Products in stock come from 25 trusted brands, so you’re sure to find the right part for your 1993 Chevrolet K1500 without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1993 Chevrolet K1500, we stock popular OEM and aftermarket Performance and Racing Products from top names like Edelbrock, FEL-PRO Performance, MSD Ignition, and more. Edelbrock Performance and Racing Products start at just $64.99 and boast an impressive 4.4 stars average rating from customers. FEL-PRO Performance and MSD Ignition also bring quality to the table, with Performance and Racing Products available starting at $31.49, and at an average 4.2 stars rating. With 606 customer reviews and counting, our 1993 Chevrolet K1500 Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1993 Chevrolet K1500 is always ready to roll. We’re committed to providing you with everything you need to keep your K1500 in top shape, all in one place. Start shopping confidently below for your 1993 Chevrolet K1500!

Best-Selling Performance Exhaust Products for 1993 Chevrolet K1500s

Enhance the driving experience in your Chevrolet with 22 quality Performance Exhaust Product components, starting at $26.99.

show more show less

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$93.99

Product Features:

Water/Weather Resistant
Re-Useable
Will Not Burn Or Blow Out
Suitable For Port-Matching
Made In USA

from

$277.99

Product Features:

Ideal For Connecting Headers
Use With FLOWTECH Headers

from

$89.99

Product Features:

Large internal flow tubes improve exhaust flow and reduce backpressure
Exclusive patented flow director design channels exhaust flow and eliminates turbulence on most applications.
Dyno proven to flow up to 700 SCFM
Dyno proven to flow up to 700 SCFM

from

$46.99

Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.

Product Features:

Withstands Intense Exhaust Heat
Reusable header, exhaust manifold and collector flange gaskets
Resists Deteriorating
Manufactured from “dead soft” aluminum layers – .125″ thick
Easy Removal For Disassembly
Conforms easily to surface irregularities (warped flanges)
Compresses down to 0.060″ to create a tight leak-proof seal
Will not shrink, deteriorate, or blow out- eliminating gasket leaks
For high performance street, drag race and oval track use

from

$156.99

DynoMax Ultra Flo Welded performance stainless steel mufflers feature 100-percent welded construction for lifelong durability. The unrestricted, straight-through design dyno proven to flow up to 2,000 SCFM and support up to 2,000 horsepower. Each muffler uses our exclusive Continuous Roving Fiberglass (CRF) Technology to absorb unwanted interior resonance while maintaining a deep performance tone. The ‘Pure Unadulterated POWER’ of DynoMax Ultra Flo Welded mufflers are backed by a Limited Warranty and limited Performance & Sound Guarantee.

Product Features:

Stainless steel construction for lifelong protection
100% welded design for maximum durability
Straight through design ensures unrestricted exhaust flow and reduces back pressure
CRF Technology absorbs unwanted interior resonance while maintaining a deep performance tone
Dyno proven to flow up to 2,000 SCFM and support up to 2,000 horsepower.

from

$34.99

Manufactured from high-temperature composite exhaust material. Provides maximum torque retention to eliminate gasket failure. Can be trimmed if necessary for modified port applications. Precision die cut for an excellent fit. For OE replacement, high-performance street, drag race and oval track.

Product Features:

High-Temperature Exhaust Material
Withstands Extreme Exhaust Heat
Provides Excellent Sealing And Durability
Superior Tensile Strength
Resists Deteriorating
Provides Excellent Torque Retention

from

$140.99

Product Features:

Made From Aluminized Case
Rust And Corrosion Protection
Stronger Seams Prevent Blow Out
Provides More Horsepower
Max Flow In Either Direction
Powerful Sound With No Resonance
Limited Lifetime Warranty

from

$69.99

Mr. Gasket CopperSEAL Header Gaskets are a high quality copper gasket that performs extremely well and are reusable. We recommend this in all racing and high performance applications. They are for stock heads unless indicated, and work well in high heat and turbocharged applications.

Product Features:

Manufactured from ¿Dead Soft¿ (solid) .043″ thick copper material
Manufactured from ┐Dead Soft┐ (solid) .043″ thick copper material
.051″ embossment around each exhaust port to seal irregular surfaces. Total gasket thickness .094″
Provides excellent sealing and durability
Conforms to and seals minor surface irregularities
For high performance street, drag race, oval track and turbocharged (extreme heat) applications

from

$28.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$37.99

Manufactured from high-temperature steel core/graphite faced exhaust material
Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
Conforms to and seals minor surface irregularities
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Anti-Stick Properties
Easy Removal For Disassembly

from

$34.99

Withstands Intense Exhaust Heat
Graphite-Impregnated Facing
Steel Expanded Metal Core
Superior Tensile Strength
Resists Deteriorating
Anti-stick Properties
Easy Removal For Disassembly

from

$49.99

Manufactured from high-temperature steel core/graphite faced exhaust material
Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
Conforms to and seals minor surface irregularities
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Anti-Stick Properties
Easy Removal For Disassembly

from

$26.99

Made from quality materials for durability, DynoMax pipe is manufactured with precision benders and fixture checked to ensure a precise fit for quick and easy installation.

Product Features:

IMPROVED FLOW CAPACITY : Mandrel bends (where applicable) improve flow capacity over traditional bends while increased pipe diameter from OE sizes increases flow and power
DESIGNED TO PERFORM : Fixture checked to ensure a precise fit for quick and easy installation
AVAILABLE IN DIFFERENT SIZES : Offered in a variety of styles and sizes for a quality vehicle repair
PREMIUM MATERIALS: Made from aluminized steel for durability and long life
BETTER TOGETHER : Use premium DynoMax accessories when installing DynoMax mufflers and exhaust systems for a complete performance exhaust system upgrade

from

$36.99

Withstands Intense Exhaust Heat
Graphite-Impregnated Facing
Steel Expanded Metal Core
Superior Tensile Strength
Resists Deteriorating
Anti-stick Properties
Easy Removal For Disassembly

from

$349.99

Product Features:

Bolt On Quickly And Easily
Top Performance/Clean Machine
Increased Efficiency
Leak Free Seal
Connects To Exhaust Head Pipe
Complete With Premium Gaskets
16-Gauge Tubing For Durability

from

$437.99

DynoMax® Ultra Flo SS Polished performance mufflers are constructed of stainless steel for lifelong durability and completely polished for show-quality shine. The unrestricted, straight-through design is dyno proven to flow up to 2,000 SCFM and support up to 1,900 horsepower. Each muffler uses our excl usive Continuous Roving Fiberglass (CRF) Technology to absorb unwanted interior resonance while maintaining a deep performance tone. The ‘Pure Unadulterated POWER’ of DynoMax® Ultra Flo SS Polished mufflers are backed by a Limited Warranty and exclusive 90-Day Performance & Sound Guarantee.

Product Features:

Stainless steel construction for lifelong protection
Polished finish for a show quality shine
Dyno proven to flow up to 2,000 SCFM and support up to 1,900 horsepower
Straight through design ensures unrestricted exhaust flow and reduces back pressure
CRF Technology absorbs unwanted interior resonance while maintaining a deep performance tone

from

$243.99

The 70 series utilizes Flowmaster’s patented Delta Flow technology and an enlarged case for improved sound control along with mileage and power gains. Perfect for use on trucks, SUV’s, RVs, tow vehicles and high performance street cars where space allows. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$217.99

The Super 50 series muffler is a larger version of Flowmaster’s 50 series Delta Flow muffler. Originally designed for trucks and SUV’s, it is also well suited to muscle car and high performance applications. In addition, the larger case size significantly reduces interior resonance and provides a deep, rich tone along with mileage and power gains. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$149.99

from

$82.99

Made from quality materials for durability, DynoMax pipe is manufactured with precision benders and fixture checked to ensure a precise fit for quick and easy installation.

Product Features:

IMPROVED FLOW CAPACITY : Mandrel bends (where applicable) improve flow capacity over traditional bends while increased pipe diameter from OE sizes increases flow and power
DESIGNED TO PERFORM : Fixture checked to ensure a precise fit for quick and easy installation
AVAILABLE IN DIFFERENT SIZES : Offered in a variety of styles and sizes for a quality vehicle repair
PREMIUM MATERIALS: Made from aluminized steel for durability and long life
BETTER TOGETHER : Use premium DynoMax accessories when installing DynoMax mufflers and exhaust systems for a complete performance exhaust system upgrade

from

$41.99

Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

Product Features:

Manufactured from high-temperature acrylic blend exhaust material
Provides excellent sealing and durability
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use

Most Popular 1993 Chevrolet K1500 Performance Ignition Products

Customize your Chevrolet with 11 Performance Ignition Products products like Performance Coils, Performance Spark Plug Wires, and Performance Ignition Kits, all priced under $316.99.

show more show less

from

$65.99

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

Helically wound conductor suppresses electro and radio noise
Kevlar core combination for great strength and durability
Heavy Duty Terminals For Secure Connection
8mm silicone and synthetic jacket resists heat and abrasion
500 Ohms/ft. Resistance For Improved Spark Delivery And Power
Silicone Boots Protect Against High Exhaust Temps

from

$77.99

MSD Ignition control are easy to install, but we also offer several direct plug-in harnesses for late model vehicles! The harnesses plug directly into your factory coil and harness then four color coded wires plug into the corresponding wires of the MSD.

Product Features:

Plug-In Harness w/Color Coded Wires
No Cutting Or Splicing
Quick Easy Installation
Provides A Direct Plug-In Installation
When Adding An MSD Ignition Control

from

$92.99

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$78.99

Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

Product Features:

Direct performance replacement for GM dual connector coil
100:1 Turns Ratio
Lower Primary Resistance Produces High Voltage Output
Works w/Stock Ignition As Well As MSD Ignitions

from

$140.99

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

Less than 50 ohms per foot for superior spark
Ferro-magnetic impregnated core creates an effective EMI choke
40 ft. Of Conductor Wound Into A Single Foot Of Wire
For high EMI suppression
Conductor core features Dupont Kevlar material
Proprietary compound sleeves for resistance to high heat/abrasion

from

$91.99

The traditional ACCEL combination of yellow wire and red spark plug boots has been added to these SuperStock Spiral Core 5000 Series wire sets, which feature color-matched wire and spark plug boots in blue, black, and red. With only 500 ohms/ft. of resistance, more ignition energy can reach the spark plug, producing a longer-lasting, hotter spark flame kernel. The results is higher performance through improved efficiency, quicker throttle response, and reduced emissions. This 8mm wire’s double silicone construction is rated to 550 degrees F. The high-gloss wire jacket resists moisture, chemicals, and heat extremes for longer life and great looks. The fiberglass braid adds greater pull strength and terminal retention, while the stainless steel spark plug terminals provide excellent long life, electrical conductivity, and corrosion resistance. Both universal and custom-fit applications are available for early and late model cars and trucks.

Product Features:

500 Ohms/ft Of Resistance
550 F Rated Silicone Jacket
Stainless Steel Plug Terminals
High RFI Suppression For Street And Strip Use
Custom-fit Universal And Import Coverage
High-strength Fiberglass Braid Construction
Pre And Post HEI Vehicles
7mm And 8mm High Gloss Silicone Jacket

from

$172.99

This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM ignition systems with the externally mounted module. 1990 thru 1995.

Product Features:

Fits Most Stock And Modified Distributors
Dwell Control Circuit
Resists False Triggering

from

$123.99

Ditch that plain-Jane stock appearance once and for all. AVS Hood Scoops add 200HP in looks alone. Its heat-resistant, UV-protected, thermoplastic material is built to last a lifetime delivering unmistakable eye appeal wherever you go. Available in smooth black nish with paintable surface so you can match your factory paint if you like. Choose from several styles and sizes in 1- and 2-piece options. Cleanly mounts with 3M automotive-grade adhesive tape concealed. . Proudly made in the USA with global materials.

Product Features:

Its High-Impact / UV Protected Thermoplastic Material Is Heat Resistant And Built To Last A Lifetime.
Available In Smooth Black Finish. If You Like / Deck Out Its Paintable Surface To Match Your Vehicles Paint Color.
No Drilling Required – Attach With The Included 3M Automotive-Grade Adhesive Tape And Youre Ready To Hit The Road.
Specially Designed To Conceal Adhesive Tape On The Underside Of Hood Scoop.
AVS Hood Scoops Come In Both One- And Two-Piece Configurations To Suit Your Personal Style.
Made In The USA With Global Materials.

from

$33.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$316.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

Replacement crank trigger wheel for small block Chevy
Absolutely the most accurate way to trigger the ignition
The non-magnetic pickup cannot be false triggered
Powerful magnets are embedded in a billet aluminum trigger wheel

from

$199.99

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

Glass Filled Polyester Case
Longer Spark Duration
Increased Performance
No Energy Loss Due To Arcing
Includes Brass Contact Terminal

Top Picks for 1993 Chevrolet K1500 Performance Air Filters

Upgrade Chevrolet K1500s with top-quality Performance Air Filters parts, including 1 OEM and aftermarket selections for your 1993 model.

show more show less

from

$41.49

Designed to be superior to stock paper filters
Comes pre-oiled
Designed for an easy installation with OE fit
Made with pre-dyed media for lasting color

In-Demand Performance Engines for 1993 Chevrolet K1500s

Select from 250 premium Performance Engines parts for your 1993 Chevrolet K1500, with prices ranging from $7.99 to $1,712.00.

show more show less

from

$42.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$44.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$31.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$346.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 Deg Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used
Accepts Late-Model Choke; Waterneck; and HEI
Accepts A/C And Alternator
Accepts Exhaust Heated Chokes

from

$64.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$20.99

Mr. Gasket cam locking plates feature a steel retainer plate designed to secure the cam gear bolts from coming loose and backing out, preventing costly engine damage. Retainer plate fits under bolt heads allowing tabs to be bent against hex head flats creating a secure positive lock.

Product Features:

Black oxide finished steel
Includes (3) grade 5 bolts & locking plate
Fits Chevrolet Small and Big Block without OE roller cam
Tabs bend up around bolt head to secure

from

$159.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Non-Rotator Style: Dyno Tested and Street Proven
Great Match to Edelbrock Camshaft Kit

from

$23.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$15.99

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

Has A Zinc Dichromate Finish
Made Of High Quality Grade 8 Steel
Has A Tall Hex Head To Prevent Wrench Slipping Off
Extra Thick Parallel Ground Washer
Washer Provides More Accurate And Uniform Torque

from

$34.99

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

Edge Molded Rubber Water Outlet Gasket Is Reusable
Requires No Gasket Sealer
Solid Aluminum Carrier For Strength/rigidity
Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

from

$29.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$29.49

Opens at 160 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully opens at Correct Temperature Consistently Regardless of engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$914.99

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:

Cam and lifter kit for Small Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
295/313 Advertised Duration, 243/257 Duration @ .050″, .500″/.486″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$898.99

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – High Energy: Good street performance with stock converter, choppy idle. OR High Energy Marine: Biggest cam for inboard/outboard. Good for ski, economy and light performance.

Product Features:

Cam and lifter kit for Small Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – High Energy: Good street performance with stock converter, choppy idle. OR High Energy Marine: Biggest cam for inboard/outboard. Good for ski, economy and light performance.
268/268 Advertised Duration, 218/218 Duration @ .050″, .454″/.454″ Lift, 110 Lobe Separation
Valve spring upgrade required

from

$449.99

Similar in performance to the Holeshot series, the Tork Master is B&M’s lowest cost torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$9.99

Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
3/8 inch-16 by 1 inch bolts
Kit includes 12 bolts and washers
Manufactured from high quality steel
Bolts feature hex heads

from

$31.99

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$20.99

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$37.99

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

Chrome Plated
Grade 5
AN washers with no exposed shoulder for a professional appearance

from

$51.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$519.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
All Factory Connections Used
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal with OEM Throttle Body
For OE and Small Bore TBI Injectors Only
No Chip Changes/Computer Modifications Required
5.7L Power Package Provides Free Computer Chip

from

$69.99

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$44.99

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair, these gaskets are .187 inch thick. They fit both 1987-2002 Gen I Chevrolet Small Blocks as well as 1992-1997 Gen II LT-Based Small Blocks.

Product Features:

Manufactured from high-density cork /rubber blend gasket material
A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
For OE replacement, high performance street, drag race and oval track
.187″ thick
Handles Ex Flange Pressure
Forms Leak Proof Seal
Black Latex Coating

from

$63.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
Not intended for use in emission controlled vehicles.

Most Sold 1993 Chevrolet K1500 Performance Oil Filters

Explore our best-selling Chevrolet parts for the 1993 K1500 among 6 OEM and aftermarket options starting from $10.79.

show more show less

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$17.99

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$16.99

FRAM Racing filters are designed with a heavy-gauge tapping plate and an extra-thick steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22PSI filter bypass valve provides additional protection against larger contaminants.

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$18.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$12.99

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$10.79

Fits General Motors cars from 1987 and later
Features a triple chrome-plated finish
Manufactured from plastic material
OEM replacement part

Top-Rated Performance and Racing Products Brands For Your 1993 Chevrolet K1500

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1993 Chevrolet K1500s. Below you’ll find some of our best rated Performance and Racing Products from Edelbrock, FEL-PRO Performance, and MSD Ignition, and more. Performance and Racing Products from these brands that fit a 1993 K1500 start at just $31.49 and are rated as high as 4.4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Edelbrock 1993 Chevrolet K1500 Performance and Racing Products

When it comes to maintaining or upgrading your 1993 Chevrolet K1500, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Edelbrock ticks all of those boxes. We offer a wide selection of Edelbrock Performance and Racing Products, specifically designed for the 1993 Chevrolet K1500. With over 3 Edelbrock brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $64.99, with an average price of just $190.66. Plus, with over 4 customer reviews and an average rating of 4.4 stars, you can trust that our Edelbrock Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $346.99

(1)

Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish

“product fit as described , no complaints”

from $159.99

(1)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

“Excellent product.”

from $64.99

(2)

Sure Seat Valve Springs for Chevy 262-400 V8 1957-95

“Used with the smallest Comp Thumpr Cam, good to 5500 RPM, Cost is great, No valve float. I would use again with a samll to medium cam and 416 heads.”

Popular FEL-PRO Performance 1993 Chevrolet K1500 Performance and Racing Products

FEL-PRO Performance auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1993 Chevrolet K1500 owner should feel confident when installing genuine FEL-PRO Performance parts in their vehicle. To ensure the best fit and performance for your 1993 K1500, Advance Auto Parts carries a full inventory of 3 FEL-PRO Performance Performance and Racing Products. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these FEL-PRO Performance Performance and Racing Products range from $31.49 to $44.99, plus, with more than 4 customer reviews and an impressive 4.2 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

from $31.49

(2)

Exhaust Manifold Gasket Set

“Appear to be A-OK on my Chevrolet as far as fitment”

from $44.99

(1)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

“Racing application”

from $42.49

(1)

Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

“Real good products”

FAQs for 1993 Chevrolet K1500 Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1993 Chevrolet K1500s?

Out of 353 Performance and Racing Products that fit 1993 Chevrolet K1500s, the following parts are the top sellers:

Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (17402826) – $17.99
High Performance 180 Degree Thermostat for Increased Flow (17360033) – $29.99
High Performance Thermostat – 160 Degree Brass & Copper (17360031) – $29.49

What’s the price range for 1993 Chevrolet K1500 Performance and Racing Products?

Performance and Racing Product prices for the 1993 Chevrolet K1500 start at $7.99 and go up to $1,712.00 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1993 Chevrolet K1500?

The average price for Performance and Racing Products for the 1993 Chevrolet K1500 is $270.54. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Chevrolet K1500 model years?

Yes, we currently carry Performance and Racing Products for 10 model years of Chevrolet K1500s between 1988 and 1999. Performance and Racing Products are bought most frequently for the following model years: 1999, 1998, 1997, 1996, 1995, 1994, 1992, 1991, and 1990.

What are the cheapest Performance and Racing Products for my 1993 Chevrolet K1500?

The cheapest 1993 Chevrolet K1500 Performance and Racing Products we carry in stock are:

Flat 1 Piece Guide Plate for Chevrolet Small Block with 5/16" Pushrod 7/16" Stud (50288900) – $7.99
Flat 1 Piece Guide Plate for Chevrolet Small Block with 3/8" Pushrod 7/16" Stud (50288110) – $7.99
High Energy 7.794" Long, 5/16" Diameter Pushrod (50289688) – $7.99
High Energy 7.266" Long, 5/16" Diameter Pushrod (50289690) – $7.99
High Energy 7.205" Long, 5/16" Diameter Pushrod (50289290) – $8.99

What are the top-rated Performance and Racing Products that fit the 1993 Chevrolet K1500?

Out of 606 reviews by customers, our 1993 Chevrolet K1500 Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1993 Chevrolet K1500 and their top-rated products:

Performance Air Filters
- Spectre Replacement Air Filter (10162558) – $41.49
Performance Steering Products
- Spectre Replacement Air Filter (10162558) – $41.49
Performance Oil Filters
- Spectre Replacement Air Filter (10162558) – $41.49

What types of Performance and Racing Products do you sell for my 1993 Chevrolet K1500?

As of 11/2/25, these are some of the most in-demand types of Performance and Racing Products for a 1993 Chevrolet K1500:

Can I get help with 1993 Chevrolet K1500 Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Performance and Racing Products and more.

What is your return policy for Chevrolet K1500 Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Chevrolet K1500 Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1993 Chevrolet K1500 Performance and Racing Products

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Edelbrock – Water Pump for Small-Block Chevy Street Rods in Polished Finish (Part No.8892)

Mr. Gasket – Valve Cover (Part No.9415)

Flowmaster Inc. – Super 40 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.952548)

Accel – Tst GM 87-95 5.0/5.7L Tbi (Part No.TST4)

Energy Suspension – Control Arm Bushing Set (Part No.3.3134R)

K&N – Cold Air Intake: Adds Up To 7 Horsepower, With Million Mile Air Filter (Part No.63-1007-1)

Competition Cams – Magnum 224/224 Hydraulic Flat Cam and Lifter Kit (Part No.CL12-212-2)

Richmond Gear – RngPnn (Part No.GM85456)

PerTronix – D4062 Flame-Thrower HEI Distributor Rotor Blue (Part No.D4062)

Energy Suspension – Leaf Spring Bushing Set (Part No.3.2128G)

Flowtech – Shorty; Smog Headers (Part No.91831FLT)

Mr. Gasket – Starter Motor Heat Shield (Part No.3678)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Spectre – Bolt Kit Intake Hex Head (Part No.4652)

Mr. Gasket – Chrome Valve Cover Wing Bolts (Part No.9824)

Mr. Gasket – Mls Head Gasket (Part No.3130G)

MSD Ignition – Distributor; Chevy V8; Billet with Vacuum Advance (Part No.8361)

B & M – TRAVELER CONVERTER (Part No.70431)

Energy Suspension – Body Cab Mount Set (Part No.3.4122G)

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Spectre – Screw In Oil Cap 87-Up (Part No.4320)

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5907)

Spectre – Spectre Replacement Air Filter (Part No.HPR0326)

Mr. Gasket – Oil Pan Bolt Kit (Part No.6085)

Mr. Gasket – Timing Tab (Part No.4600)

Mr. Gasket – Timing Tab (Part No.4593)

Mr. Gasket – Timing Tab W/Adjustable Pointer – Chrome Plated – For 7" Harmonic Balancers (Part No.4597)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1444)

Flowtech – Real-Seal; Header Gasket (Part No.99150AFLT)

Flowtech – Y-Pipes (Part No.11504YFLT)

Dynomax – Super Turbo Exhaust Muffler: Universal Fit, Aluminized Steel, 13" L, 3" In, 2.5" Out, Oval (Part No.17674)

Mr. Gasket – Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal (Part No.7401G)

Dynomax – Ultra Flo Exhaust Muffler: Universal Fit, Stainless Steel, 14" L, 3" In, 2.5" Out, Oval (Part No.17228)

Mr. Gasket – Exhaust Gasket Set (Part No.150)

Flowtech – Afterburner Muffler, 3in Center Inlet 2.5in Dual Offset Outlet, Non-Reversible, Aggressive Sound (Part No.50370FLT)

Mr. Gasket – Copper Seal: Exhaust Gasket Set (Part No.7152G)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1402)

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5900)

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5907)

Mr. Gasket – Ultra-Seal Exhaust Gaskets – Hi-Temp Graphite – Small Block Chevy Oval Port – 1.50"W X 1.82"H (Part No.5917)

Dynomax – Exhaust Pipe (Part No.43661)

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5902)

Flowtech – Shorty; Smog Headers (Part No.91831FLT)

Dynomax – Ultra Flo Muffler: Direct Fit, Stainless Steel, 23" L, 3" In, 2.5" Out, Oval (Part No.17273)

Flowmaster Inc. – 70 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, 22in long, Non-Reversible, Mild Sound (Part No.52573)

Flowmaster Inc. – Super 50 Muffler, 3in Center Inlet 2.5in Dual Offset Outlet, Non-Reversible, Moderate Sound (Part No.530552)

Flowmaster Inc. – Super 40 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.952548)

Dynomax – Exhaust Tail Pipe (Part No.45212)

Mr. Gasket – Exhaust Gaskets – Standard Duty – Small Block Chevy Square Port, 1.45"W X 1.48"H – Reusable (Part No.150C)

MSD Ignition – Wire Set; Street Fire; Chevy Truck 305-350; 85-on (Part No.5562)

MSD Ignition – Harness; MSD 6 to GM Dual Connector Coil (Part No.8876)

Mallory – Unilite Ignition Module (Part No.605)

MSD Ignition – Coil; GM External HEI Coil; High Performance (Part No.8226)

MSD Ignition – Wire Set; Super Conductor; Small Block Chevy with HEI Cap (Part No.35599)

Accel – 8Mm Super Stock Spiral Cust Bk (Part No.5114K)

Accel – GM Ext. Coil 90-95 Ign Module (Part No.35370)

Auto Ventshade (AVS) – Eclipse, Large Hood Scoops (Part No.80001)

Mallory – Distributor Wiring Harness (Part No.29349)

MSD Ignition – Trigger Wheel; Flying Magnet; Small Block Chevy (Part No.8611)

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Spectre – Spectre Replacement Air Filter (Part No.HPR0326)

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1003)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Edelbrock – Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish (Part No.2104)

Edelbrock – Sure Seat Valve Springs for Chevy 262-400 V8 1957-95 (Part No.5802)

Mr. Gasket – Cam Bolt Lock Plate Kit (Part No.948G)

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1602)

Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.945G)

Mr. Gasket – Premium Quality Thermostat Gasket with Solid Aluminum Carrier (Part No.738G)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Mr. Gasket – High Performance Thermostat – 160 Degree Brass & Copper (Part No.4363)

Competition Cams – Big Mutha’ Thumpr 243/257 Hydraulic Flat Cam/Lifter Kit (Part No.CL12-602-4)

Competition Cams – High Energy/Marine 218/218 Hydraulic Flat Cam/Lifter Kit (Part No.CL12-210-2)

B & M – Tork Master 2000: Value-Priced Street Performance Torque Converter (Part No.70420)

Spectre – Bolt Kit Intake Hex Head (Part No.4652)

Mr. Gasket – High Performance Thermostat (Part No.4365)