from

$14.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$63.99

Product Features:

Trac Loc spring
Fits 28 spline Ford 8.8

from

$4.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$7.99

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

Pinion nut for Ford 7.5″, 8″ and 9″
3/4″ x 20 thread
1 1/6″ socket

from

$336.99

Yukon positraction internals for 8.8″ Ford with 28 spline axles. This kit fits Yukon Gura Grip & Eaton positractions. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 8.8″ with Yukon Dura Grip positraction with 28 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$176.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$209.99

Product Features:

Spider gear kit
Fits Ford 8.8″ 31 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$719.99

Product Features:

Trac Loc positraction
Fits Ford 8.8″ with 31 spline axles

from

$241.99

8.8″ Ford TracLoc (with short ears–for late models only) clutch set, both sides.

Product Features:

Clutch kit
Fit Ford 8.8″ Trac Loc positraction

from

$137.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

MASTER KIT FORD 8.8″

from

$99.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$18.49

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$0.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$35.99

Product Features:

MINI INSTALL KIT FORD 8.8

from

$167.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2009 and down Ford 8.8″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$62.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (Includes Supershims).

Product Features:

Fits Ford 8.8″
Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$315.99

Yukon 1541H alloy rear axle for ’03 and newer 8.8″ Ford Crown Victoria (non-Limo) with ABS. axle has a length of 34-3/8″ inches and 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

Fits 2003 and up Crown Victoria, Grand Marquis, Marauder and Town Car
28 spline
34 3/8″ long
5 lug
This axle is ABS compatible and includes ABS tone ring

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$5.99

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$1489.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio