1992 Chevrolet Camaro Performance Engines

Utilizes late model alternator and A/C bracket mounting provisions. Has vacuum taps off Manifold runners. Uses cable bracket P/N 20-101 for GM 700R4 transmission. Extra installation hardware included.

Product Features:

• High Rise Dual Plane Design
• Holley Pro-Jection Tbi Mounting Flange
• Erg Provisions

This Spectre engine dress-up kit was designed for the 1987 – 1995 Chevy 305 & 350 engines. This kit includes: stock height valve covers, chrome valve cover T-bolts, chrome oil filler cap, chrome PCV breather, grommets, and an air cleaner adapter stud. The air filter adapter stud, is a z-bolt that is designed to allow you to use a center stud style air cleaner assembly instead of the stock dual-stud setup. Manufactured using high quality materials this kit features triple chrome plated parts.

Product Features:

• For 1987-1995 Chevrolet 305-350 engines
• Includes stock height valve covers & T-bolts
• Includes oil filler caps, pcv vent filter
• Includes air cleaner Z-Stud
• Chrome engine kit

Edelbrock part #7208 Intake Gaskets for 1965-1990, Mark IV 396-402-427-454-555, Rectangular Port 6 Bolt Flange with no crossover allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, an

Product Features:

• 1.82″x2.46″
• Rectangular Port Style
• .060″ Thick
• Two Piece Configuration
• Composite Material

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Larger diameter increases flow and performance. Direct bolt-on. No modifications necessary. Manufacture red on sophisticated machinery. Butterflies are precision machined. Includes new machined throttle position sensor. Bolts to stock on aftermarket manifold. All stock sensors and lines fit like stock.

Product Features:

• Larger Diameter Increases Flow and Performance
• Direct Bolt-On; No Modifications Necessary
• Manufactured On Sophisticated Machinery
• Butterflies Are Precision Machined
• Includes New Machined Throttle Position Sensor
• Bolts To Stock Or Aftermarket Manifold
• All Stock Sensors And Lines Fit Like Stock

Manufactured from cellulose and nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement, high performance street, drag race and oval track.

Product Features:

• Maxi-seal fiber material
• Superior blow-out resistance
• High-tensile strength
• Reduces gasket splitting
• Graphite non-wicking rubber
• No cork particles
• Easy removal for disassembly

Mr. Gasket manufactures a variety of performance parts and accessories, including carburetor and fuel accessories, cooling system accessories, engine components, fasteners, gaskets, and suspension and drive line components. Besides gaskets and fasteners, the Mr. Gasket brand provides a variety of performance and racing products for all parts of your vehicle including: carburetor and fuel accessories, chrome-plated accessories, cooling system accessories, engine components, ignition and electrical accessories, shifter accessories, specialty tools and suspension and driveline components. Mr .Gasket also includes Ultra-Seal gaskets and fasteners.

Product Features:

• Nitrile rubber and high density cork
• Will not shrink or stick

This stud uses heat treated grade 8 alloy steel. The enlarged radius base provides extra strength for a more durable stable shank. Black plated finish. Fits Chevy small block and Ford small block.

Product Features:

• Heat-treated
• Grade 8 alloy steel
• Ex strength enlarged radius
• More durable/stable shank
• Prevents stud flexing
• Black plated finish

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

• Sure-lock rocker arm nuts
• Precise valve train adjustment
• Keep rocker arms locked
• High-quality grade steel
• Heat-treated for ex strength
• Plated with durable gold tone finish

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets

Product Features:

• Timing Chain Only

Avoid trouble with this precision timing tape. Use it for accurate timing, setting valve lash or when degreeing the harmonic balancer.

Product Features:

• Accurate in calibration
• For hi-performance engines
• Increased performance
• Set valve lash at proper time

The grade 8 bolts feature high hex head to prevent socket slippage. The thick parallel ground washer allows accurate uniform torque. Black finished, complete with split lock washer to prevent loosening.

Product Features:

• These are have a zinc dichromate finish
• Tall hex head bolt to prevent slippage
• Extra thick parallel ground washer
• Washers provides more accurate and uniform torque
• Grade 8 alloy steel

Edelbrock #88503 Water Pump big block Chevy short black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pu

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 5.750 in. Block To Hub Height
• Black Finish

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

• Twisted Snout Water Pump Design For Updated Style
• Street Performance
• Heavy Duty Shaft w/5/8 in. Pilot
• Six-Blade Stamped Steel
• Anti-Cavitation Impeller
• 100 Percent Leak Tested

Grade 8, single bolt. Black plated finish. The washers are designed to secure the Mr. Gasket cam button pn1180, pn1181, and pn1183 or can be used as stock replacements.

Product Features:

• Specialty and drive train fastener
• Special cam bolts
• Black plated finish

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

Product Features:

• Case-Hardened Tubing
• Surface Hardening
• Welded Ends
• 0.3125 in. Diameter
• Use with or without Hardened Steel Guideplates

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.
• Not intended for use in emission controlled vehicles.

This chrome plated water neck is precision die cast for a great fit. It features an O-ring style seal to prevent water leaks. These water necks are first polished to a high luster then chrome plated for lasting beauty.

Product Features:

• Chrome plated aluminum
• O-ring style to prevent leaks
• Swivels for hard to fit applications
• Comes with allen head bolts

Features two threaded bosses for temp control switch satin finish.

Product Features:

• Emission System Water Outlet

With the ever-increasing technology in performance and racing engines, supercharged, turbo charged, nitrous-oxide and extreme compression ratios, a demand was created for stronger, more durable engine gaskets. Mr. Gasket, the originator of high performance gaskets, has met the challenge and developed performance gaskets in a variety of materials for all applications to meet the sealing demands of these engines. Mr. Gasket engine gaskets are the most advanced, tested and proven in the performance market today and earned the respect of many professional and sportsman racers.

Product Features:

• Steel shimmed for perfect sealing
• Increases engine compression
• High temp silicone coated to prevent leaks
• Stress formed embossments

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only