from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$167.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2009 and down Ford 8.8″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$483.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
18 piece kit
Steel clutches

from

$99.99

Yukon outer stub axle for Chrysler 9.25″ front. This axle uses a 1485 u/joint and has 33 splines.

Product Features:

Fits Ford 8.8″
Steel

from

$153.99

This kit uses Koyo bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and br

Product Features:

Fits 2009 and down Ford 8.8″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

from

$194.99

Mini Spool for Ford 8.8″ with 31 spline axles and 7/8″ cross pin. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″ with 31 spline axles
Provides 100% traction to both wheels at all times
Installs into standard open carrier case

from

$201.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 2009 and down Ford 8.8″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$35.99

Product Features:

MINI INSTALL KIT FORD 8.8

from

$834.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits Ford 8.8″ with 28 spline axles
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$16.99

Standard open cross pin shaft (.750″) for Ford 8″, 8.8″, 9″ and Model 20.

Product Features:

Cross pin shaft for Ford 8″, 8.8″ and 9″ and AMC Model 20
Fits standard open differentials only
0.750″ diameter

from

$59.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles.
Quality materials – all components are built for reliable longevity and performance.
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$15.29

CUP

from

$228.99

Product Features:

FRD 10BL 8.8 R/P 3.55 MG

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$30.99

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Ford 7.5″, 8.8″, 9″ and 10.25″

from

$2.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$99.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$8.99

Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

Pinion gear thrust washer
Fits Ford 8.8″
0.750″ I.D.

from

$15.99

SHAFT SEAL

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles.
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged.
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$20.49

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit.

Product Features:

.047″ thick cellulose/nitrile composite gasket material
Precision die cut
Reusable

from

$14.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features: