1990 Ford F-350 Pickup Drivetrains

Below you will find various in-demand Ford Drivetrains, components and accessories for your 1990 F-350 Pickup. Advance Auto Parts has popular F-350 Pickup parts like Drive Shafts and Axles, 4WD Components, Transfer Cases and more. You’ll also find aftermarket and OEM Drivetrains for other F-350 Pickup model years including 1988, 1989, 1991, 1992, 1993, 1994, 1995, 1996, 1997 and more. Select a category of 1990 Ford F-350 Pickup Drivetrains below and start saving instantly.

Popular 1990 Ford F-350 Pickup Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

Drive Shaft Support Bolts

U-Joints

4WD Hubs

Transfer Case Assemblies

Transfer Case Adapter Gaskets

Transfer Case Gaskets

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Axle Shafts

Bearing Pullers

Locking Hub Spindle Nuts

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Locking Hub Service Kits

Axle Spindle Seals

U-Joint Centering Yokes

Differential Cover Bolts

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Axle Spindle Bearings

Differential Disc Kits

Axle Vents

Differential Clutch Packs

Differential Ring and Pinions

Stub Axles

U-Joint U-Bolt Kits

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Axle Spindles

Differential Air System Seal Housings

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Axle Nuts

Front Differential Cover Gaskets

Rear Housing Cover Gaskets

Axle Hubs

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Transfer Case Differential Bearings

Differential Seals

Complete Differentials

Bearing and Seal Overhaul Kits

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Carrier Bearing Shims

Axle U-Bolt Kits

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Pinion Shaft Seals

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Mounting Adapter Seals

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Differential Drive Pinion Oil Deflectors

Differential Carrier Bolts

Differential Pinion Gear Washers

Output Shaft Pilot Bearings

Spindle Washers

Differential Ring and Pinion Kits

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

Differential Clutch Pack Clips

Axle Shaft Flange Caps

Differential Pinion Bearing Spacers

Universal Joint Snap Rings

Double Cardan CV Weld Yokes

Axle Shaft O-Rings

Essential Drivetrains for 1990 Ford F-350 Pickups

from

$22.99

Ford 10.25″ C/clip.

Product Features:

C-clip
Fits Ford 10.25″

from

$7.99

Product Features:

Oil baffle
Fits Dana Spicer 70 and 70HD

from

$129.99

Product Features:

Drive flange cap
Fits Dana 60
Yukon engraved

from

$339.99

Yukon long yoke for ’93 and newer Ford 10.25″ and 10.5″ with a 1410 U/joint size. 4.188″ snap ring span, 1.118″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 1993 and up Ford 10.25″ and 10.5″
31 spline
1410 u-joint size
4.188″ snap ring span
1.188″ cap diameter
Outside snap ring design
Strap style

from

$42.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.

from

$324.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 70HD
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$11.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 375, 430, 434 & 498
Fits 1-1/8″ bearings

from

$232.99

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

from

$33.49

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$31.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific, providing unsurpassed quality for a seal you can trust
Validated for fit, form, and function
Engineered for the sealing repair environment
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$126.99

Product Features:

Carrier shim kit
Fits Dana Spicer 70 and 70HD

from

$374.99

Round replacement yoke companion flange for Dana 80. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 80
37 spline
Round companion flange

from

$88.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$3.99

Product Features:

Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″

from

$44.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$52.99

Air line repair kit, ZIP locker.

Product Features:

Air line repair kit
Includes 20′ air line and two repair fittings

from

$8.99

Product Features:

Axle o-ring
Fits Ford 10.25″ and 10.5″

from

$284.99

Yukon 1541H replacement outer stub axle shaft for ’88-’99 Dana 60 with a length of 11.4 inches and with 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy front axles come with a one year warranty against manufacturing defects.

Product Features:

30 spline
11.4″ long
Fits Dana Spicer 60 in 1988-1999 Ford F350
Outer stub
5-332X U-joint size

from

$1432.99

Evolution Driveline products, are remanufactured to meet or exceed OEM specifications for quality, fit, and performance. Every transfer case we sell passes a comprehensive battery of tests on our computerized test center. We recreate actual driving conditions and analyze performance before the product even leaves the factory, so you can buy with confidence.

Product Features:

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$37.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$78.99

Seal housing for Ford 10.25″ & 10.5″, Zip locker, with o-rings.

Product Features:

Seal housing for Ford 10.25″ and 10.5″
Includes o-rings

from

$389.99

Yukon replacement standard open carrier case for Dana 60, 4.56 & up (incl ABS) 2-7/16″ tall.

Product Features:

Standard open carrier case
Does not include spider gears
Fits Dana Spicer 60
4.56 and up ratio only
ABS and non-ABS compatible

from

$46.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$18.40

Trans Case Output Sh

from

$10.49

Product Features:

Brand may vary by location

from

$10.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$19.29

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

Upgrade your 1990 Ford F-350 Pickup with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1990 Ford F-350 Pickup, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your F-350 Pickup functioning at its best. At Advance Auto Parts, we offer a wide selection of 631 Drivetrains for the 1990 Ford F-350 Pickup, designed to meet your needs without breaking the bank. From Drive Shafts and Axle replacements to 4WD Components upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1990 Ford F-350 Pickup at great prices. Our Drivetrains inventory for this model ranges from just $2.59 to $2,784.99, with an average price of $310.91. Our 631 Drivetrains in stock come from 26 trusted brands, so you’re sure to find the right part for your 1990 Ford F-350 Pickup without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1990 Ford F-350 Pickup, we stock popular OEM and aftermarket Drivetrains from top names like Moog, Driveworks, National, and more. Moog Drivetrains start at just $9.99 and boast an impressive 4 stars average rating from customers. Driveworks and National also bring quality to the table, with Drivetrains available starting at $3.49, and at an average 4 stars rating. With 2,725 customer reviews and counting, our 1990 Ford F-350 Pickup Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1990 Ford F-350 Pickup is always ready to roll. We’re committed to providing you with everything you need to keep your F-350 Pickup in top shape, all in one place. Start shopping confidently below for your 1990 Ford F-350 Pickup!

Best-Selling Drive Shafts and Axles for 1990 Ford F-350 Pickups

Enhance the driving experience in your Ford with 67 quality Drive Shafts and Axle components, starting at $3.93.

show more show less

from

$20.29

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$34.49

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.48 INCH / 63 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
NOT PICTURED: TWO DUST SHIELDS

from

$9.49

This axle vent is designed to match the fit and function of the original vent on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this axle vent is designed to match the fit and function of the original vent on specified vehicles.
Restores functionality – reliable replacement for an original vent that has failed due to blockage or fatigue.
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$49.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$15.99

DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$42.99

from

$73.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$81.99

from

$44.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$44.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$22.79

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
COMPLETE MOUNT

from

$19.99

Value-priced bearing meets all cataloged application requirements.

from

$29.49

Drive Shaft Center Support

from

$21.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$16.29

The axle shaft o-ring seals the rear axle to the wheel hub. The symptom of a failed axle shaft o-ring is an axle fluid leak around wheel hub. This is an ideal repair solution to prevent axle fluid leaks from forming around the wheel hub.

Product Features:

Aftermarket exclusive replacement part.
Recommended for replacement when servicing vehicle brakes.
Direct replacement for original equipment
This part has undergone extensive vehicle try-on and durability testing to ensure strength, fitment and longevity

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$4.49

Product Features:

Brand may vary by location

from

$39.99

Product Features:

Brand may vary by location

from

$375.99

Replacement front spindle for Dana 60, 92-98 Ford F350, 5 holes, 7″ long, 7″ flange.

Product Features:

Fits 1992-1998 Ford F350 with reverse rotation Dana Spicer 60 front
7.00″ tall
7.00″ flange
5 bolt holes

from

$136.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Ford E350/F350 F/F Dana 60 & Dana 70 rear replacement axle bearing kit, 67-97. This axle bearing & seal kit services one side only.

Product Features:

Fits 1967-1997 Ford F350 and E350 rear with Dana Spicer 60 or 70
Includes inner and outer bearings and races and axle seal
Services one side

from

$61.90

Rugged SKF drive shaft support bearings are built to meet or exceed OE specifications. They are also built on the years of experience that SKF has earned designing and supplying bearings to the world’s largest OE manufacturers. Engineered and manufactured to specific application requirements that deliver precise drive shaft alignment and support. Center support bearings are pre-lubricated and sealed with metal reinforced seals to prevent contamination. Rubber support cushions are manufactured from durable rubber compounds that provide maximum support while isolating the driveline shaft from damaging vibration. Drive shaft support frames are constructed from high quality steel or aluminum that provides additional strength and long life in harsh environments.

Product Features:

OE Quality, fit and performance
Precise driveshaft alignment and support
Pre-lubricated and sealed
Metal reinforced seals to prevent contamination
Manufactured from durable rubber compounds

from

$17.26

Spindle Nut

from

$7.99

Product Features:

Pinion yoke dust shield
Fits Dana Spicer 60 and 70

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$334.99

Yukon replacement yoke for Dana 80 with a 1410 U/joint size. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 80
37 spline
1410 u-joint size
4.188″ snap ring span
1.188″ cap diameter
Outside snap ring design
Strap style

from

$89.23

Driveshaft Support

from

$32.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$1381.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1309.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1301.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1282.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1281.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1269.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1269.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1232.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1189.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1105.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1056.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$941.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$781.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$567.99

Driveshaft – Front

from

$527.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$454.99

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$284.99

30 spline
11.4″ long
Fits Dana Spicer 60 in 1988-1999 Ford F350
Outer stub
5-332X U-joint size

from

$274.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit for 10.25″ Ford (full-floating). This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.

Product Features:

Fits Ford 10.25″
Includes inner and outer bearings and races and axle seal
Services one side

from

$256.99

Yukon 4340 Chrome-Moly replacement outer stub for Dana 60, ’88-’99 Ford F350 with a length of 11.4″ and 30 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

Fits 1988-1999 Ford F350
4340 Chromoly
Outer stub
30 spline
11.4″ from end of splines to center of u-joint bore

from

$233.99

Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
Strap style

from

$219.99

Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1350 u-joint size
3.625″ snap ring span
1.188″ cap diameter
Outside snap ring design
U-bolt style

Top Picks for 1990 Ford F-350 Pickup Transfer Cases

Upgrade Ford F-350 Pickups with top-quality Transfer Cases parts, including 25 OEM and aftermarket selections for your 1990 model.

show more show less

from

$25.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$5.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$37.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$16.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$14.29

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$30.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$10.79

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications.
Effective fix – restores a tight seal in the transfer case after original gasket fails.
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$8.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$4.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$31.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific, providing unsurpassed quality for a seal you can trust
Validated for fit, form, and function
Engineered for the sealing repair environment
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$24.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$16.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$94.49

Product Features:

BW1356 BEARING & SEAL KIT ALSO 1370 (W/O THE CENTER PLATE)

from

$43.99

TCaseGasketSealKit

from

$1432.99

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$171.99

TCaseBrg-SealKit

from

$164.99

TRANSFER CASE PARTS

from

$115.99

TCaseBrg-SealKit

from

$15.49

BEARING

from

$14.79

Product Features:

Brand may vary by location

from

$13.10

Transfer Case Gasket

from

$10.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$10.49

Product Features:

Brand may vary by location

from

$5.99

TCase Thrust Washer

from

$2.99

Seal

In-Demand Universal Joints for 1990 Ford F-350 Pickups

Select from 80 premium Universal Joints parts for your 1990 Ford F-350 Pickup, with prices ranging from $2.59 to $999.99.

show more show less

from

$59.99

Backed by superior materials and rigorous testing, MOOG Heavy Duty universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$9.99

For U-Joints 330 & 331
Contains two 1.81″ bolt center clamps and four 5/16-24 x 3/4″ cap screws

from

$39.99

from

$11.99

For U-Joints 375, 430, 434 & 498
Fits 1-1/8″ bearings

from

$42.99

from

$6.79

Universal Joint – Brute Force

from

$2.59

Universal Joint Strap Kit

from

$25.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$26.99

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging to provide higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting allows for easy maintenance and the flexible use of the entire assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals are applied to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$29.99

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$33.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$34.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$50.99

from

$36.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$34.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$36.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$19.99

BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$32.49

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$25.99

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$6.29

This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles.
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$15.99

Universal Joint

from

$8.39

Universal Joint – Brute Force

from

$7.89

Universal Joint

from

$4.59

Universal Joint

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$5.49

Universal Joint – Brute Force

from

$5.39

Universal Joint

from

$37.99

from

$30.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$39.99

from

$105.99

Machined bodies to meet the tight tolerances
Forged and cast material to meet the performance requirement
Minimize the flash lines for less interference
Cleaning process induces compressive strength for increased performance
Machined and threaded holes for mounting ease
Rust preventative added for longer shelf life

from

$73.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$36.99

from

$46.99

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$72.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$30.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

Most Sold 1990 Ford F-350 Pickup Differentials

Explore our best-selling Ford parts for the 1990 F-350 Pickup among 429 OEM and aftermarket options starting from $2.99.

show more show less

from

$9.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$9.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$38.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$39.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$9.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$11.79

Formulated to meet the specific requirements of Toyota, Lexus, and scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF T-IV is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking

from

$245.99

Product Features:

DANA-70 R/P 4.10 STD MG 72154-5X .625″ OFFSET

from

$8.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$33.99

Product Features:

KIT SHIM CARRIER 10.25″ FORD

from

$13.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$32.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$13.99

10.25″ & 10.5″ cover gasket.

Product Features:

Cover gasket
Fits Ford 10.25″ and 10.5″

from

$63.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles.
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid.
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$5.99

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles.
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$15.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$23.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$4.99

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
1/2″ x 18 thread

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$6.99

Ring Gear bolt for Ford 10.25″ & 10.5″. 1/2″ x 20.

Product Features:

Ring gear bolt for Ford 10.25″ and 10.5″
1/2″ x 20 thread

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$9.99

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
0.480″ tall

from

$7.99

Repleacement ring gear bolt for Dana 80. 9/16″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 80
9/16″ x 18 thread

from

$47.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$14.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$13.99

Product Features:

Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$25.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$26.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$16.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$6.49

Product Features:

DANA PRELOAD SHIMS (D60 & D70)

from

$19.99

Product Features:

Pinion preload shims for Dana Spicer 60 and 70U

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$83.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$27.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$18.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$24.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$13.99

Product Features:

PINION SHIM – DANA 70 ALL

from

$79.99

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

Seal housing for Dana Spicer 60
Includes o-rings

from

$61.99

DIFF COVER KIT

from

$18.99

Product Features:

CARRIER SHIM-DANA 60 & 70

Top-Rated Drivetrains Brands For Your 1990 Ford F-350 Pickup

Shop for the best-rated brands offering Drivetrains and other products for your 1990 Ford F-350 Pickups. Below you’ll find some of our best rated Drivetrains from Moog, Driveworks, and National, and more. Drivetrains from these brands that fit a 1990 F-350 Pickup start at just $3.49 and are rated as high as 4 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Moog 1990 Ford F-350 Pickup Drivetrains

When it comes to maintaining or upgrading your 1990 Ford F-350 Pickup, using quality Drivetrains is essential to ensure durability and a perfect fit. Moog ticks all of those boxes. We offer a wide selection of Moog Drivetrains, specifically designed for the 1990 Ford F-350 Pickup. With over 22 Moog brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $9.99, with an average price of just $39.81. Plus, with over 527 customer reviews and an average rating of 4 stars, you can trust that our Moog Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$30.99

This product is not rated

Greaseable Super Strength Universal Joint

“”

from
$105.99

This product is not rated

Double Cardan CV Centering Yoke

“”

from
$73.99

This product is not rated

Non-Greaseable Super Strength Universal Joint

“”

Popular Driveworks 1990 Ford F-350 Pickup Drivetrains

Driveworks auto parts is one of the highest quality Drivetrain brands in the market. Any 1990 Ford F-350 Pickup owner should feel confident when installing genuine Driveworks parts in their vehicle. To ensure the best fit and performance for your 1990 F-350 Pickup, Advance Auto Parts carries a full inventory of 30 Driveworks Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these Driveworks Drivetrains range from $4.49 to $42.99, plus, with more than 200 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from
$8.49

This product is not rated

Tapered Cup Wheel Bearing Assembly

“”

from
$4.79

This product is not rated

Oil Seal

“”

from
$4.49

This product is not rated

Oil Seal

“”

FAQs for 1990 Ford F-350 Pickup Drivetrains

Which Drivetrains are best-sellers for 1990 Ford F-350 Pickups?

Out of 631 Drivetrains that fit 1990 Ford F-350 Pickups, the following parts are the top sellers:

Universal Joint (10265505) – $15.99
Greaseable Super Strength Universal Joint (10086947) – $36.99
Universal Joint (10265720) – $15.99

What’s the price range for 1990 Ford F-350 Pickup Drivetrains?

Drivetrain prices for the 1990 Ford F-350 Pickup start at $2.59 and go up to $2,784.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1990 Ford F-350 Pickup?

The average price for Drivetrains for the 1990 Ford F-350 Pickup is $310.91. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford F-350 Pickup model years?

Yes, we currently carry Drivetrains for 41 model years of Ford F-350 Pickups between 1953 and 1997. Drivetrains are bought most frequently for the following model years: 1997, 1996, 1995, 1994, 1993, 1992, 1991, 1989, and 1988.

What are the cheapest Drivetrains for my 1990 Ford F-350 Pickup?

The cheapest 1990 Ford F-350 Pickup Drivetrains we carry in stock are:

Universal Joint (18270063) – $2.59
Seal (12009365) – $2.99
Differential Crush Sleeve (10282338) – $2.99
Ring Gear Bolt (20520495) – $2.99
Differential Cover Gasket (10282407) – $3.29

What are the top-rated Drivetrains that fit the 1990 Ford F-350 Pickup?

Out of 2,725 reviews by customers, our 1990 Ford F-350 Pickup Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1990 Ford F-350 Pickup and their top-rated products:

4WD Components
- MileMarker Supreme; Manual Hub (99994389) – $428.99
Spindles
- MileMarker Supreme; Manual Hub (99994389) – $428.99
Universal Joints
- MileMarker Supreme; Manual Hub (99994389) – $428.99

What types of Drivetrains do you sell for my 1990 Ford F-350 Pickup?

As of 2/5/25, these are some of the most in-demand types of Drivetrains for a 1990 Ford F-350 Pickup:

Can I get help with 1990 Ford F-350 Pickup Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford F-350 Pickup Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford F-350 Pickup Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1990 Ford F-350 Pickup Drivetrains

Yukon Gear – Ford 10.25" C/Clip (Part No.33078)

Yukon Gear – Replacement Baffle For Dana 70 & 70HD (Part No.33003)

Yukon Gear – Dana 60 Drive Flange Cap, Engraved (Part No.32133)

Yukon Gear – Long Yoke For ’93 And Newer Ford 10.25" And 10.5" With A 1410 U/Joint Size (Part No.41042)

Spicer – Universal Joint (Part No.5-178X)

Yukon Gear – Pinion Install Kit For Dana 70-HD & Super-70 Differential (Part No.13034)

MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.534-10)

Yukon Gear – Full-Floating, Blank 35 Spline Diameter, Non-Drilled Axle Shaft For Dana 60 (Part No.21005)

Dorman – Spindle Nut 2 In.-16 L Hex Size 3 In. (Part No.615-134.1)

Felpro – Transfer Case Adapter Gasket (Part No.55484)

Yukon Gear – Replacement Carrier Shim Kit For Dana 70 & 70HD (Part No.55019)

Yukon Gear – Round Replacement Yoke Companion Flange For Dana 80 (Part No.41036)

Pro-King – Differential Carrier Cover (Part No.716C758)

Yukon Gear – Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (Part No.33164)

National – Multi Purpose Bearing (Part No.HB-88107-A)

Yukon Gear – Air Line Repair Kit, Zip Locker (Part No.34003)

Yukon Gear – Axle O-Ring For Ford 10.25" & 10.5" (Part No.33465)

Yukon Gear – 1541H Replacement Outer Stub Axle Shaft For ’88-’99 Dana 60 (Part No.21102)

EVO Driveline – Remanufactured Transfer Case (Part No.UMT416-1)

Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)

National – Shaft Repair Sleeve (Part No.99199)

Yukon Gear – Seal Housing For Ford 10.25" & 10.5", Zip Locker, With O-Rings (Part No.34040)

Yukon Gear – Replacement Standard Open Carrier Case For Dana 60, 4.56 & Up (Part No.20046)

National – Bearings (Part No.308)

SKF – Trans Case Output Sh (Part No.J7121366773SKF)

Driveworks – Transfer Case Input Shaft Seal (Part No.S-714503)

National – Multi Purpose Seal (Part No.710062)

National – Multi Purpose Seal (Part No.473468)

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

Dorman – Rear Axle Differential Vent (Part No.924-263)

National – Multi Purpose Seal (Part No.710492)

Driveworks – Universal Joint (Part No.DW-331BL)

Spicer – Universal Joint (Part No.5-178X)

National – Multi Purpose Bearing (Part No.HB-88508-A)

Spicer – Universal Joint (Part No.SPL55-3X)

Spicer – Universal Joint (Part No.5-1350X)

National – Multi Purpose Bearing (Part No.HB-88107-A)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

Driveworks – Ball Bearing (Part No.S-HB-88107-A)

Driveworks – Drive Shaft Center Support (Part No.S-HB-88508-A)

National – Bearings (Part No.HM88649)

Dorman – Rear Axle O-Ring Kit (Part No.926-163)

Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)

Driveworks – Oil Seal (Part No.S-225010)

Driveworks – Axle Shaft Seal (Part No.S-710492)

Yukon Gear – Replacement Front Spindle For Dana 60, 92-98 Ford F350 (Part No.32267)

Yukon Gear – Dana 60/70 Rear Axle Bearing And Seal Kit Replacement (Part No.10055)

SKF – Driveshaft Support with Bearing (Part No.K1030325692SKF)

Dorman – Spindle Nut (Part No.K1002831650DOR)

Yukon Gear – Pinion Yoke Dust Shield For Dana 60 & 70 (Part No.33441)

Yukon Gear – The Carrier Bearing Puller (Part No.56072)

Yukon Gear – Replacement Yoke For Dana 80 With A 1410 U/Joint Size (Part No.41034)

SKF – Driveshaft Support (Part No.K10301069521SKF)

National – Bearings (Part No.88107-BVV)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.946-941)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.946-943)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-225)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-219)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-223)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-224)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-220)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-222)

Dorman – Front Driveshaft Assembly (Part No.938-354)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.986-373)

Dorman – Front Drive Shaft: Greaseable, Adjustable (Part No.938-312)

Dorman – Front Drive Shaft: Greaseable, Adjustable (Part No.938-248)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-953)

USA Standard Gear – Driveshaft – Front (Part No.44529)

Cardone – Drive Shaft: Greasable, Direct Replacement (Part No.65-9667)

Cardone – Drive Shaft: Not Greasable, Direct Replacement (Part No.65-9721)

Yukon Gear – 1541H Replacement Outer Stub Axle Shaft For ’88-’99 Dana 60 (Part No.21102)

Yukon Gear – Ford 10.25" Rear Axle Bearing And Seal Kit (Part No.10034)

Yukon Gear – 4340 Chrome-Moly Replacement Outer Stub For Dana 60, ’88-’99 Ford F350 (Part No.21415)

Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41022)

Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1350 U/Joint Size (Part No.41027)

Milemarker – MileMarker Supreme; Manual Hub (Part No.449S/S)

Milemarker – MileMarker Supreme; Manual Hub (Part No.459S/S)

National – Multi Purpose Seal (Part No.3946)