1990 Ford F-250 Pickup Belts and Hoses
More 1990 Ford F-250 Pickup Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1990 Ford F-250 Pickup, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1990 Ford F-250 Pickup Belts and Hoses
Gates – Premium Molded Coolant Hose (Part No.20662)
from
$19.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Yukon Gear – Seal Puller Tool (Part No.56063)
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25487)
from
$35.49
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.21403)
from
$35.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dorman – Fuel Filler Neck Hose (Part No.573-012)
from
$44.99
Fuel filler neck leaking? This replacement fuel filler neck hose is engineered and thoroughly tested to match the original filler neck for specific vehicle years, makes and models for a reliable repair.
Product Features:
See More
Product Features:
- Direct replacement – this fuel filler neck hose is made to match the original equipment part on specific vehicles
- Durable construction – made of fuel-resistant materials to reduce future failure potential
- Regulatory compliant – built to meet emission and inspection standards
- Trustworthy value – backed by team of engineers and quality control experts in the United States
Dorman – Fuel Filler Neck Hose (Part No.573-011)
from
$81.99
Fuel filler neck leaking? This replacement fuel filler neck hose is engineered and thoroughly tested to match the original filler neck for specific vehicle years, makes and models for a reliable repair.
Product Features:
See More
Product Features:
- Direct replacement – this fuel filler neck hose is made to match the original equipment part on specific vehicles
- Durable construction – made of fuel-resistant materials to reduce future failure potential
- Regulatory compliant – built to meet emission and inspection standards
- Trustworthy value – backed by team of engineers and quality control experts in the United States
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 76 mm Diameter (Part No.900005A)
from
$24.99
This pulley is manufactured by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 90 mm Diameter (Part No.906003A)
from
$19.99
This pulley is manufactured by Litens Automotive the original equipment part supplier and the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Heavy duty thermoplastic construction for long life and trouble-free performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by Litens, the largest original equipment tensioner and pulley supplier in the world, to ensure proper form, fit, and performance
- Heavy Duty Glass Reinforced Polymer Pulley for optimized dimensional control and running surface durability
- Installation instructions included.
Carquest Premium – Fuel Injector Return Hose Kit (Part No.AL002)
from
$45.99
This complete kit includes necessary components to replace the fuel injector return lines and copper gaskets on the fuel injectors.
Product Features:
See More
Product Features:
- Includes fuel return line
- Includes 8 fuel injector copper combustion seals
- Includes 8 injector O-rings
- Includes 18 clamps
- Includes 8 plastic return fittings
- Premium OE quality materials
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25477)
from
$17.79
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.72" Diameter (Part No.E71963)
from
$60.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Dorman – Engine Oil Cooler Line (Part No.625-201)
from
$181.99
This engine oil cooler hose assembly matches the fit and function of the original equipment components for reliable repair and restoration of proper oil circulation between the oil cooler and engine.
Product Features:
See More
Product Features:
- Ideal replacement – this engine oil cooler hose assembly is a direct replacement for the original hose assembly
- Quality materials – this engine oil cooler hose assembly is made from corrosion-resistant materials to ensure the smooth transfer of oil from the engine to the cooler
- Easy to install – no special tools required
- Quality tested – rigorous quality control ensure this hose assembly conforms to product standards
Dayco – V-Belt Assy. Idler/Tensioner Pulley; Steel, 94mm Dia., 19.3mm Width, Grooves (Part No.89025)
from
$30.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 90mm Dia., 39.5mm Width, Smooth (Part No.89048)
from
$46.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Driveworks – Automotive V-Belt, Driveworks (Part No.42315)
from
$5.99
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Gates – Notched V-Belt: 38.12" Long, 1 Strand, Exact Fit (Part No.9375)
from
$37.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Dayco – Poly Rib Belt HD Serpentine Belt; 99.25 Long, 8 Rib Count, Heavy Duty (Part No.5080993)
from
$75.99
Produced for heavy-duty vehicles and buses with multiple accessories, Dayco HD poly-V belts are made from EPDM material to resist heat and are compliant with the latest standards, guaranteeing resistance, reliability, low noise and longer service life. En
Product Features:
See More
Product Features:
- Engineered to handle operating conditions with temperatures up to 130°C (266°F)
- Designed for multiple accessories such as A/C, power steering pumps, alternators and water pumps
- Capable of delivering excellent performance in high torque and high power pulse applications
- Specially formulated treated cord insures length and tension stability on heavy duty diesel engine drives for the life of the belt
Dayco – Poly Rib Belt Serpentine Belt; 99.02 Long, 6 Rib Count (Part No.5060990)
from
$66.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 7 Inch Length (Part No.87603)
from
$27.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.18070)
from
$27.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999263A)
from
$91.99
Litens Automotive is the original equipment (O.E.) supplier of this tensioner for Ford Pickups and Vans. The Litens replacement part meets all form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). This part is manufactured in Canada by Litens to the same exacting specifications as the O.E. part. The tensioner maintains a integrated location pin as well as the internal damping design specified for this diesel application. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the original equipment part supplier to ensure proper form, fit and performance
- Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
- Installation instructions included.
- Heavy Duty Steel Pulley (Note: The pulley on the OE tensioner may be plastic. The pulley on was upgraded to Steel for the aftermarket).
- Professional Mechanics will change this tensioner in about 1 hour.
- Due to the fact that belts and tensioners have similar Original Equipment “design life targets”, it is often a best practice to replace the belt tensioner when replacing a worn or broken belt.
- Belt removal is required to change the tensioner. Therefore, doing both together will extend accessory drive life and lower overall labor versus performing these services separately.
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999118A)
from
$88.99
Litens Automotive is the original equipment supplier of this tensioner for this Ford application. The Litens replacement part meets all form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). The Litens replacement part maintains the round wire spring and internal damping components specified by the O.E. manufacturer. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the original equipment part supplier to ensure proper form, fit and performance
- Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
- Heavy Duty Thermoplastic Pulley
- Professional Mechanics will change this tensioner in approx. 20 minutes
- Due to the fact that belts and tensioners have similar Original Equipment “design life targets”, it is often a best practice to replace the belt tensioner when replacing a worn or broken belt.
- Belt removal is required to change the tensioner. Therefore, doing both together will extend accessory drive life and lower overall labor versus performing these services separately.
- Installation instructions included.
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter (Part No.900007A)
from
$41.99
This pulley is manufactured by Litens Automotive the original equipment part supplier and the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction for long life and trouble-free performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by Litens, the largest original equipment tensioner and pulley supplier in the world, to ensure proper form, fit, and performance
- Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance
- Installation instructions included.
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 90 mm Diameter (Part No.900053A)
from
$23.99
This pulley is manufactured by Litens Automotive the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Heavy duty thermoplastic construction for long life and trouble-free performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by Litens, the largest original equipment tensioner and pulley supplier in the world, to ensure proper form, fit, and performance
- Heavy Duty Glass Reinforced Polymer Pulley for optimized dimensional control and running surface durability
- Installation instructions included.
Dorman – Heater Hose Connector (Part No.800-403)
from
$15.49
Made of quality materials, this HVAC heater hose connector matches the fit and function of an original equipment connector to restore leak-free performance.
Product Features:
See More
Product Features:
- Quality replacement – this heater hose connector matches the fit and function of the original equipment connector
- Durable construction – this heater hose connector is made of quality materials for a precise fit and leak-free durability
- Cost-effective solution – offers original equipment quality at competitive price
- Performance tested – this connector has been rigorously pressure tested to ensure reliable performance
Dorman – Help – Heater Hose Connector – 5/8 In. Tube x 5/8 In. Hose (Part No.47165)
from
$15.99
Made of quality materials, this HVAC heater hose connector matches the fit and function of an original equipment connector to restore leak-free performance.
Product Features:
See More
Product Features:
- Quality replacement – this heater hose connector matches the fit and function of the original equipment connector
- Durable construction – this heater hose connector is made of quality materials for a precise fit and leak-free durability
- Cost-effective solution – offers original equipment quality at competitive price
- Performance tested – this connector has been rigorously pressure tested to ensure reliable performance
Dorman – Heater Hose Connecto (Part No.R30361329114DOR)
from
$10.15
Heater Hose Connecto
Popular 1990 Ford F-250 Pickup Belts and Hoses Categories
1990 Ford F-250 Pickup Belts and Hoses
You count on your 1990 Ford F-250 Pickup to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 147 Belts and Hoses ranging in price from $1.49 to $110.99, you’re sure to find everything you need for your 1990 Ford F-250 Pickup.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 13 different brands like Dayco, Litens, and Driveworks. 1990 Ford F-250 Pickup Belts and Hoses start as low as $1.49!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 2,396 extensive product reviews on 1990 Ford F-250 Pickup Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Poly Rib Belt Serpentine Belt; 99.02 Long, 6 Rib Count with 4.4 stars and Poly Rib Belt Serpentine Belt; 91 Long, 6 Rib Count with 4.4 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1990 Ford F-250 Pickup below to get started!
Top-Rated Belts and Hoses Brands For Your 1990 Ford F-250 Pickup
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1990 Ford F-250 Pickup running right for years to come. In our inventory you’ll find brands like Dayco, Litens, Driveworks, and even more.
Popular Litens Belts and Hoses
You’ll find popular Litens brand products across Pulleys. All are waiting to get your 1990 Ford F-250 Pickup back on the road. Some of the top-rated Litens products in these categories are:
from
$28.99
(7)
O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 76 mm Diameter
Belt Tensioner Pulleys
from
$23.99
(2)
O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 90 mm Diameter
Belt Tensioner Pulleys
from
$19.99
(1)
O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 90 mm Diameter
Idler Pulleys
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1990 Ford F-250 Pickup, and some of our most reviewed Dayco parts include:
from
$30.99
(516)
Serpentine Idler/Tensioner Pulley; Direct Fit, 90 mm Diameter, 30 mm Smooth
Belt Tensioner Pulleys
FAQs for 1990 Ford F-250 Pickup Belts and Hoses
What are the most purchased Belts and Hoses for the 1990 Ford F-250 Pickup?
Out of 147 Belts and Hoses for the 1990 Ford F-250 Pickup, the most popular in our inventory are:
from
$33.49
(39)
O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter
Idler Pulleys
What are the top-rated 1990 Ford F-250 Pickup Belts and Hoses?
Top-rated Belts and Hoses for your 1990 Ford F-250 Pickup based on customer reviews/ratings are:
from
$41.99
(49)
Poly Rib Belt Serpentine Belt; 91 Long, 6 Rib Count
“Ordering was painless and pickup at the store was a breeze!”
from
$20.79
(41)
Serpentine Idler/Tensioner Pulley; Polymer, 90mm Dia., 31mm Width, Smooth
“Noise was coming from pulley not the belt! I replaced a very good belt for nothing!”
