from

$635.99

RngPnn

from

$189.99

Set-up carrier bearing (2 bearings, no races) 25590. No return.

Product Features:

Set up bearing kit
Fits Dana Spicer 44
Easily slips on and off carrier journals to allow for easier carrier shim adjustment

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$22.99

8.8″ Reverse inner pinion bearing oil baffle.

Product Features:

Oil baffle
Fits Ford 8.8″ IFS

from

$269.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1993 and up Dana Spicer 44 IFS
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$11.99

9″ Ford gasket.

Product Features:

Dropout gasket
Fits Ford 9″

from

$487.99

Yukon Trac Loc internals for 8″ & 9″ Ford, 31 spline, includes hub & clutches. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 9″ with Trac Loc positraction with 31 spline axles
Includes two side gears, four pinion gears, cross pin shaft, clutch hub, roll pin and spider gear thrust washers.

from

$11.29

Product Features:

O-ring for seal housing
Fits Dana Spicer 44 and Toyota 8″ and V6

from

$41.99

Product Features:

Shim kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction

from

$215.99

Bearing race driver for Dana 44 rear. (TK 31520) No return.

Product Features:

Bearing race driver
Fits 31520 race
All steel construction

from

$4.99

Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For use with Trac Loc limited slip
1.25″ long

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles
Quality materials – all components are built for reliable longevity and performance
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$275.99

8.75″ Chrysler & 55P Chevy Power Lok clutches, Model 20 also, POSI.

Product Features:

Clutch kit
Fits Chrysler 8.75″, 1955-1964 GM passenger car and AMC Model 20 Powr Lok positraction

from

$11.99

Pinion gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:

Pinion gear thrust washer for Ford 8.8″
0.875″ diameter cross pin shaft applications only

from

$223.99

Yukon replacement trail repair kit for Dana 30 and 44 with 1310 size U/joint and straps. This kit comes with a yoke, U/joint, pinion seal, U/bolt or strap kit, pinion nut, and pinion nut washer (if applicable).

Product Features:

Fits Dana Spicer 30 and 44
1310 u-joint size
Kit includes yoke, U-joint, pinion seal, pinion nut and washer, straps, bolts and threadlocker

from

$12.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$719.99

Product Features:

Trac Loc positraction
Fits Ford 8.8″ with 31 spline axles

from

$33.99

Product Features:

MINI INSTALL KIT FORD 9″

from

$3.99

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

from

$39.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$44.99

Product Features:

Spring kit for Dana Spicer 28, AMC Model 35 IFS, Dana Spicer 44 IFS and Dana Spicer 50 IFS
Allows for installation of positraction or locker

from

$101.99

Product Features:

MINI SPOOL 8.8 FORD 31SPL

from

$7.99

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

Pinion nut for Ford 7.5″, 8″ and 9″
3/4″ x 20 thread
1 1/6″ socket

from

$57.99

Product Features:

Fits Ford 9″ with 31 spline axles
Installs into a standard open carrier case
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$6.99

Product Features:

Inner oil slinger for Dana Spicer 25, 27, 30, 44 and 50

from

$16.99

Product Features:

Cross pin shaft for Dana Spicer 44
Fits standard open differentials only

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features: