1990 Chevrolet Camaro Performance Engines

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Die-cut for an excellent fit
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Edelbrock #8895 Water Pump GM gen III ls1 & gen iv ls engines insert style ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “supe

Product Features:

• Standard Impeller Rotation
• 0.750 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 6.00 in. Block To Hub Height
• Natural Finish

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

• Valve Spring Retainers for Use OE Cast Iron Heads
• Superior Quality Heat-Treated Steel
• Machined for Strength with Black Oxide Finish
• Finish Ensures Rust and Corrosion Protection

Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Product Features:

• Manufactured from .020″ steel shim stock.
• Thinner than composition head gaskets – increases engine compression.
• Stress formed embossments seal extreme cylinder pressures.
• For high performance street, drag race and oval track use.

Includes: 2 short flat black valve covers 2 valve cover gaskets 1 flat black push-on breather 1 flat black dipstick & tube 1 flat black timing chain cover 1 flat black timing tab 1 rubber grommet for valve cover PCV hole 1 breather grommet

Product Features:

• Ideal Starter Kit
• Enhances Appearance

Reduced Travel OE-Style Hydraulic Roller Lifter for ’87+ SBC, LT/LS and V6

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

• 8″ diameter
• 1970-73, 396-427-454 cu. in.
• 1967-69, 302 cu. in.
• 1965-68, 327 cu. in. hi-performance
• 1970-76, 400 cu. in.
• 1970-73, 350 cu. in.

Designed to take advantage of the GM LS engine’s larger camshaft journal diameter, the XFI RPM camshaft line takes Xtreme Energy technology to deliver excellent power.

Product Features:

• Designed with Xtreme Energy technology to provide excellent power with the LS engine’s enhanced cylinder head design and high RPM potential.
• Takes advantage of the LS engine’s larger journal diameter, base circle and 1.7+ rocker arm ratio.
• Provides outstanding low RPM torque with increased stability.

These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed

Product Features:

• Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
• For applications with less than 350 lbs. of open spring pressure
• Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
• Ultimate street roller rocker arm designed for serious performance enthusiasts

Product Features:

• Replacement Gasket Set For PN[4242]

Manufactured from high-density cork/rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals. For original equipment replacement and high performance street.

Product Features:

• Manufactured from high-density cork /rubber blend gasket material
• Provides excellent sealing and durability
• Complete with molded rubber front/rear oil pan end seals
• For OE replacement and high performance street use

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens at 160 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully opens at Correct Temperature Consistently Regardless of engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

• Edge Molded Rubber Water Outlet Gasket Is Reusable
• Requires No Gasket Sealer
• Solid Aluminum Carrier For Strength/rigidity
• Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

Mr. Gasket cam locking plates feature a steel retainer plate designed to secure the cam gear bolts from coming loose and backing out, preventing costly engine damage. Retainer plate fits under bolt heads allowing tabs to be bent against hex head flats creating a secure positive lock.

Product Features:

• Black oxide finished steel
• Includes (3) grade 5 bolts & locking plate
• Fits Chevrolet Small and Big Block without OE roller cam
• Tabs bend up around bolt head to secure

This Mr. Gasket Rear Main Seal is made from Viton&reg: Rubber. This style of rubber can handle high temperature like silicone rubber, but with superior abrasion resistance. Its durability and it’s double, offset lip seal design make it recommended for applications that have high engine vacuum, like racing engines that utilize external vacuum pumps for crankcase evacuation.

Product Features:

• Repairs That Leaky Rear Main Sail
• Viton« Rubber Offers Both Abrasion Resistance & High Temperature Tolerance
• Viton® Rubber Offers Both Abrasion Resistance & High Temperature Tolerance
• Upgrade for Rope Seal Equipped Cars or Silicone Rubber Main Seals

BIG BLOCK CHEVY HYDRAULIC COMPLETE KIT – Magnum: Great for street machines. Use headers and 9:1+ compression. In 396-402 use 2500+ stall and lower gears. Rough idle.

Product Features:

• K-Kit includes cam, lifters, valve springs, valve locks, retainers, valve stem seals, timing set, assembly lube, instructions and decals
• HYDRAULIC – Magnum: Great for street machines. Use headers and 9:1+ compression. In 396-402 use 2500+ stall and lower gears. Rough idle.
• 280/280 Advertised Duration, 230/230 Duration @ .050″, .520″/.520″ Lift, 110 Lobe Separation
• Can be used with mild ratio rocker arms and traditional performance valve springs.

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Talk about a smooth operator, this Holley airfoil kit easily adapts to the stock GM throttle body on Chevrolet 5.7L TPI and LT1 engines used on Camaros and Firebirds. It acts to smooth out and minimize the turbulence of the incoming flow of air into the throttle body. The September, 2002 edition of GM high-tech performance magazine reported a 5.8 horsepower increase after installing this Holley airfoil kit on a stock 1994 Camaro Z28 LT1. Installation is easy; simply snap it into place in the mouth of the throttle body and it’s ready to work. Made from space age elastomer, the Holley airfoil will perform effectively and unobtrusively for years.

Product Features:

• Smoothes and Minimizes Turbulence
• Increased Airflow
• Creates More Horsepower
• Easy Installation
• Made From Space Age Elastomer
• Effective And Unobtrusive
• Long Lasting

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• Produces at Least 18 More Horsepower
• Best Matched with Edelbrock 500cfm Carburetor

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

• Work with .530″ guides and 3/8″ valve stem diameter
• Valve stem oil seals keep unwanted oil from entering the combustion chamber
• Several different types of valve seals are offered

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

• Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
• 3/8 inch-16 by 1 inch bolts
• Kit includes 12 bolts and washers
• Manufactured from high quality steel
• Bolts feature hex heads

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

• Zinc plated to resist corrosion and provide a clean professional appearance
• Made from Grade 5 steel for strength and durability
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Allen (socket) Head
• Zinc Plated For Protection

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes sixteen (16) 3/8 inch-16 x 1-1/4 inch bolts & washers

Product Features:

• Zinc plated Grade 5 steel
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Ideal For Minimal Space
• 12-Point Head And Flange
• Zinc Plated For Protection