Name: Sure Seat Valve Springs for S/B Ford 289/302/351W O.E. Cast iron heads
Brand: Edelbrock
SKU: 5722
Price: 76.99 USD

from

$76.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$18.99

Avoid trouble with this precision timing tape. Use it for accurate timing, setting valve lash or when degreeing the harmonic balancer.

Product Features:

Accurate in calibration
For hi-performance engines
Increased performance
Set valve lash at proper time

from

$40.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
5.4L Cobra R; Upper intake
Not intended for use in emission controlled vehicles.

from

$338.99

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$432.99

Edelbrock Part #7521 RPM Air-Gap intake manifold is designed for the small-block 302 CID Ford V8 or 331-347 stroker applications. The RPM Air-Gap incorporates the same race-winning technology that?s been used on our Victor Series competition intakes and i

Product Features:

RPM Air-Gap for 302-331-347 Small-Block Ford V8
Air-Gap design features an open air space under the plenum
Separates fuel and air from engine heat
Larger runners over standard 7121 manifold
Includes nitrous bosses

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$550.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$373.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$958.99

50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Hand-Blended Intake and Exhaust Bowls
CNC-Matched Intake/Exhaust Ports in Std Location
Thicker Deck Surfaces than Other Brands
Heli-Coils in Rocker Studs and Exhaust Bolt Holes

from

$757.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Torque Improved Over Stock
Accept V8 Pedestal Rocker Arms
Accept V8 Valvetrains

from

$190.99

Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:

7.7 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$210.99

Product Features:

Case-Hardened Tubing
Surface Hardening
Welded Ends
0.3125 in. Diameter
Use with or without Hardened Steel Guideplates

from

$40.99

Super Intake Manifold Bolts

from

$107.99

Product Features:

Highest Quality Head Bolts
Cold-Formed/Heat Treated
Ensures Molecular Integrity
Reduced Diameter Bolt Heads
Hardened/Parallel-Ground Washers Included
Rated At 170000 psi
Manufactured By ARP

from

$237.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$77.99

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

Sure-lock rocker arm nuts
Precise valve train adjustment
Keep rocker arms locked
High-quality grade steel
Heat-treated for ex strength
Plated with durable gold tone finish

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$32.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$30.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$29.99

Product Features:

Timing Chain Only

from

$185.99

Product Features:

Dial-In Your Camshaft With Ease
Made From Induction Hardened Billet Steel
Solid Bushing Chain Resists Stretching
Billet SAE-1144 Steel Crank Sprockets
Multiple Keyways

from

$103.99

Manufactured from nitrile coated spring steel layers. Stress formed embossment provides excellent sealing. Also provides stability and reduces cylinder bore distortion. Ideal for super charged, turbo charged, nitrous oxide and extreme compression ratios. For high performance street, drag race and oval track. Packaged individually.

Product Features:

Ss layers with a elastomer coating
Stress formed embossments to seal ext pressure
Provides stability and reduces cyl distortion
For high performance street drag and oval track

from

$58.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$51.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$52.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

1989 Ford F-150 Pickup Performance Engines

More 1989 Ford F-150 Pickup Performance Engines

Essential 1989 Ford F-150 Pickup Performance Engines

Edelbrock – Sure Seat Valve Springs for S/B Ford 289/302/351W O.E. Cast iron heads (Part No.5722)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1614)

Mr. Gasket – Precision Timing Tape (Part No.1594)

FEL-PRO Performance – Upper Intake Manifold (Plenum) Gasket Set: 2 Piece Set (Part No.1236)

B & M – Torque Converter, Tork Master 2000 (Part No.40427)

Edelbrock – RPM Air-Gap #7521 Intake Manifold for Small-Block Ford 302-331-347 V8 (Part No.7521)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)

Competition Cams – High Energy 206/206 Hydraulic Flat Cam for Ford 221-302 (Part No.31-215-2)

Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam and Lifter Kit for Ford 351W (Part No.CL35-250-4)

Edelbrock – Street Legal Performer; Cylinder Head (Part No.603519)

Edelbrock – Performer; Cylinder Head (Part No.60299)

Edelbrock – Pushrod Set for Ford 351W (Part No.9659)

Edelbrock – Pushrod Set for Small Block Ford 289-302 (Part No.9632)

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

Mr. Gasket – Ultra Seal; Sure-Lock Rocker Arm Nuts (Part No.923G)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2941)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2921)

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1820)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1811)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1809)

Edelbrock – TIMING CHAIN (Part No.7844)

Edelbrock – Hex-A-Just By Cloyes Adj. True-Roller Timing Chain Set (Part No.7335)

Mr. Gasket – MLS Head Gasket (Part No.3175G)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1013)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-2)

Popular 1989 Ford F-150 Pickup Performance Engines Categories

1989 Ford F-150 Pickup Performance Engines

Performance Engines Brands To Make Your 1989 Ford F-150 Pickup Last

Popular FEL-PRO Performance Performance Engines

Top 1989 Ford F-150 Pickup Performance Engines from FEL-PRO Performance

FAQs for 1989 Ford F-150 Pickup Performance Engines

What are the most purchased Performance Engines for the 1989 Ford F-150 Pickup?

What are the top-rated 1989 Ford F-150 Pickup Performance Engines?

More Popular Parts for All Makes