1989 Chevrolet Caprice Performance Engines

Essential 1989 Chevrolet Caprice Performance Engines

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Engine Valve Cover Gasket Set

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Weiand – Action +Plus; Water Pump (Part No.9212P)

Action +Plus; Water Pump

from

$215.99
Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:
  • Twisted Snout Water Pump Design For Updated Style
  • Street Performance
  • Heavy Duty Shaft w/5/8 in. Pilot
  • Six-Blade Stamped Steel
  • Anti-Cavitation Impeller
  • 100 Percent Leak Tested
See More

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

PERFORMANCE REAR MAIN SEAL SET

from

$36.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet (Part No.3702)

Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet

from

$306.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched to Edelbrock Performer Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

Edelbrock – Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy (Part No.2703)

Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy

from

$322.99
Edelbrock part #2703 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thro

Product Features:
  • Idle-5500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
  • Satin Finish
  • Non-EGR W/ Oil Fill Tube
See More

Mr. Gasket – Ultra Seal: Screw-In Rocker Arm Studs (Part No.1076)

Ultra Seal: Screw-In Rocker Arm Studs

from

$65.99
Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Grade 8 Steel
See More

B & M – Holeshot 3600 (Part No.20425)

Holeshot 3600

from

$825.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
  • Dual Pattern Drive Lugs
  • New Turbine Hub
  • New Springs/Rollers In Stator
See More

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers

from

$17.49
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:
  • Zinc plated to resist corrosion and provide a clean professional appearance
  • Made from Grade 5 steel for strength and durability
  • Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
  • Allen (socket) Head
  • Zinc Plated For Protection
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1800)

PERFORMANCE OIL PAN GASKET SET

from

$18.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Performer Series Retainer (Qty 16)

from

$99.99
Product Features:
  • Use W/ Valve Springs Part #5703, 5794
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Edelbrock – Intake Manifold Gasket for 1958-1986 Small-Block Chevy (Part No.72018)

Intake Manifold Gasket for 1958-1986 Small-Block Chevy

from

$244.99
Any gasket can create a seal, but a good gasket can do it with reduced clamping force and for a long period of time. Edelbrock gaskets are manufactured from extremely high-quality materials and are specifically designed to fit Edelbrock intakes and cylinder heads, so there’s no chance that they will interfere with component operation.

Product Features:
  • 10-Pack of 7201 Intake Gasket Sets
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Pushrod Set for S/B Chevy

from

$187.99


Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9646)

Pushrod Set for S/B Chevy

from

$203.99
Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:
  • 7.25 in. Length
  • 0.312 in. Diameter
  • 4130 Chromoly Steel Material
  • Black Oxide Finish
  • Made In The USA
See More

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1000)

Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

from

$59.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5780G)

Ultra Seal: Head Gasket

from

$64.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 3.870 inch, Compressed thickness 0.028 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Advance And Retard Cam Bushings

from

$42.49
With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:
  • Advance the cam for increased torque and horsepower
  • Tune your powerband for more end torque or increase top end horsepower
  • Includes (4) offset bushings and (1) 0 degree bushing
  • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
  • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
  • Increase Top-End Horsepower
See More

Mr. Gasket – Timing Cover Gasket Set (Part No.94)

Timing Cover Gasket Set

from

$21.79
Mr. Gasket Performance Gaskets are a low density material that conforms well to irregular flange surfaces and has very good crush resistance at high flange pressures. Intended for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit.brbrThis Mr. Gasket Performance Timing Cover Gasket Kit includes the timing cover gasket and water pump gasket for your Gen IV or Gen V Chevy 396,402,427,454 Big Block.

Product Features:
  • Includes Timing Cover Gasket and Water Pump Gaskets
  • Won’t shrink or stick and provide an airtight leak proof seal
  • Engineered specifically for big block Chevys and ideal for high performance and race applications
  • Ensures optimum torque retention ideal crush resistance and excellent sheer strength using minimal clamp force yet still releases easily
See More

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Engine Timing Cover Gasket

from

$20.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Steel core gasket construction
  • Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam (Part No.42-222-4)

Xtreme Energy 218/224 Hydraulic Flat Cam

from

$548.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Competition Cams – CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA (Part No.12-601-8)

CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA

from

$522.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Cylinder Head Dowel Pins

from

$14.99
Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4377)

Cylinder Head Dowel Pins

from

$17.79
Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 396-402-427-454 V8 (Part No.5795)

Complete Sure Seat Valve Spring Kit for Chevy 396-402-427-454 V8

from

$225.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Non-Rotator Style: Dyno Tested and Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

from

$151.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Non-Rotator Style: Dyno Tested and Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

Edelbrock – XX Performer Big-Block Chevy Oval Port Hydraulic Flat Tappet Cam Polished (Part No.604919)

XX Performer Big-Block Chevy Oval Port Hydraulic Flat Tappet Cam Polished

from

$1084.99
The Edelbrock #604919 Performer Bare High Compression Cylinder Heads are designed for Big-Block Chevy Oval Port V8 applications. These Edelbrock Performer Series Cylinder heads are 50-state street legal and provide outstanding performance from Idle-5,500

Product Features:
  • High Compression
  • 100cc Combustion Chamber Volume
  • 290cc Intake/110cc Exhaust Runner Volume
  • 2.19 in. Intake/1.88 in. Exhaust Valve Diameter
  • 0.562 in. Deck Thickness
See More

Edelbrock – Engine Cylinder Head (Part No.60849)

Engine Cylinder Head

from

$605.99


Product Features:
  • 50-State Street Legal Aluminum Cylinder Head
  • Out-of-the-Box Bolt-On Performance
  • Hand-Blended Intake and Exhaust Bowls
  • CNC-Matched Intake/Exhaust Ports in Std Location
  • Thicker Deck Surfaces than Other Brands
  • Hardened Tip Stainless Swirl-Polished Valves
  • Heli-Coils Rocker Studs And Exhaust Bolt Holes
See More

1989 Chevrolet Caprice Performance Engines

Maybe you’re in the middle of a full rebuild of that 1989 Chevrolet Caprice. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 66 different Performance Engines in our inventory ranging from $14.99 to $1,028.99. That means you can find the exact parts or products you need to keep that 1989 Chevrolet Caprice running smoothly.

Performance Engines are only as good as their brand. We stock 7 different brands to make sure you have plenty of trusted parts to choose from for your 1989 Chevrolet Caprice. Mr. Gasket, FEL-PRO Performance, and Weiand are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1989 Chevrolet Caprice, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 205 reviews in this category, some of the top rated parts include Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish with 5.0 stars and PERFORMANCE VALVE COVER GASKET SET with 5.0 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1989 Chevrolet Caprice rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1989 Chevrolet Caprice Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1989 Chevrolet Caprice demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your Caprice the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular FEL-PRO Performance Performance Engines

We carry FEL-PRO Performance parts in our stock across Performance Engine Cylinder Head Gaskets categories, plus more. For a 1989 Chevrolet Caprice, our most popular FEL-PRO Performance Performance Engines include:
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $52.99
(1)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
from $39.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Engine Valve Cover Gasket Set
from $23.49
(1)
Engine Valve Cover Gasket Set
Performance Engine Valve Cover Gasket Sets

Top 1989 Chevrolet Caprice Performance Engines from Mr. Gasket

Mr. Gasket products are another trusted brand when it comes to Performance Engines for your 1989 Chevrolet Caprice. Popular Mr. Gasket parts include:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats

FAQs for 1989 Chevrolet Caprice Performance Engines

What are the most purchased Performance Engines for the 1989 Chevrolet Caprice?

Out of 66 Performance Engines for the 1989 Chevrolet Caprice, the most popular in our inventory are:
Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers
from $17.49
This product is not rated
Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers
Performance Intake Manifold Hardware
Action Plus Water Pumps
from $215.99
(3)
Action Plus Water Pumps
Performance Engine Water Pumps
Action Plus Water Pumps
from $215.99
(2)
Action Plus Water Pumps
Performance Engine Water Pumps

What are the top-rated 1989 Chevrolet Caprice Performance Engines?

Top-rated Performance Engines for your 1989 Chevrolet Caprice based on customer reviews/ratings are:
Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish
from $329.99
(1)
Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish
“product fit as described , no complaints”
PERFORMANCE VALVE COVER GASKET SET
from $23.49
(1)
PERFORMANCE VALVE COVER GASKET SET
“Great Quality Product”
Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95
from $151.99
(1)
Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95
“Excellent product.”