1988 Pontiac Grand Prix Performance and Racing Products
More 1988 Pontiac Grand Prix Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1988 Pontiac Grand Prix, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1988 Pontiac Grand Prix Performance and Racing Products
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)
from
$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5861)
from
$37.99
Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are an extra thick .312 inch which can help with valvetrain clearance.
Product Features:
See More
Product Features:
- Manufactured from high-density cork /rubber blend gasket material
- A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
- Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
- For OE replacement, high performance street, drag race and oval track
- An extra thick .312″ which can help with valvetrain clearance
Dynomax – Direct Fit Catalytic Converter: No Fabrication Needed, EPA Compliance (Part No.24235)
from
$99.99
DynoMax Race Bullet mufflers feature 100-percent welded construction for lifelong durability. The ‘Pure Unadulterated POWER’ and lightweight, compact design make it the ultimate race muffler. The unrestricted, straight-through design is dyno tested and t
Product Features:
See More
Product Features:
- Designed for vehicles with limited space
- Light weight compact design
- 100% welded design for maximum durability
- CRF Technology which helps provide up to a 4 dbA sound reduction, on most race applications, while maintaining a deep race tone
Flowmaster Inc. – 50 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Moderate Sound (Part No.942051)
from
$154.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
MSD Ignition – Wire Set; Black Super Conductor; Small Block Chevy with HEI Cap (Part No.35593)
from
$109.99
The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.
Product Features:
See More
Product Features:
- Less than 50 ohms per foot for superior spark
- Ferro-magnetic impregnated core creates an effective EMI choke
- 40 ft. Of Conductor Wound Into A Single Foot Of Wire
- For high EMI suppression
- Conductor core features Dupont Kevlar material
- Proprietary compound sleeves for resistance to high heat/abrasion
MSD Ignition – Wire Set; Street Fire; SBC; Socket Distributor Cap over VC (Part No.5565)
from
$72.99
The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.
Product Features:
See More
Product Features:
- Helically wound conductor suppresses electro and radio noise
- Kevlar core combination for great strength and durability
- Heavy Duty Terminals For Secure Connection
- 8mm silicone and synthetic jacket resists heat and abrasion
- 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
- Silicone Boots Protect Against High Exhaust Temps
Accel – Custom Fit 8.8mm; Spark Plug Wire Set (Part No.8849)
from
$113.99
These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.
Product Features:
See More
Product Features:
- 8.8mm Graphite Suppression
- Silicone Spark Plug Boots
- 550 Degree Double Silicone Construction
- Fiberglass Braid
- Carbon/Graphite Core
- Magnetic Suppression
- Fiberglass/Kevlar Core
- 500 Ohms Resistance
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2001)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2003)
from
$22.29
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-1017)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- Designed to allow high flow rates and a consistent flow of oil to your engine
- Pleated synthetic-blend filtration media removes most harmful contaminants
- Fast and easy Wrench-Off removal using the welded one-inch hex nut
- High capacity to withstand the service intervals recommended by vehicle manufacturers
- Heavy-duty canister for outstanding durability
- Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
- Designed to operate with all synthetic, conventional, and blended motor oils
MSD Ignition – Coil; GM External HEI Coil; High Performance (Part No.8226)
from
$71.99
Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.
Product Features:
See More
Product Features:
- Direct performance replacement for GM dual connector coil
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Works w/Stock Ignition As Well As MSD Ignitions
Accel – Supercoil (Part No.140001)
from
$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
MSD Ignition – Coil; GM Coil Pack; 2 Tower Style (Part No.8224)
from
$76.99
The updated Fuel Pump Booster is an easy way to maintain the proper fuel pressure on your car after adding a power adder such as a turbo or supercharger. The new model allows you to make your boost adjustments through a PC for improved control and accuracy. The Booster ensures that the engine receives the fuel it needs to make up for the increase in air being pumped into the intake manifold. It will increase the voltage to the factory fuel pump in proportion to manifold boost pressure in order to maintain the proper fuel delivery. The amount of increase is adjustable from a range of an additional 1.5 -22 volts up to 30 psi which can all be set and adjusted from your PC with MSD’s easy to use Windows based software. The MSD Booster will wire to the factory fuel pump relay or with a secondary booster pump.
Product Features:
See More
Product Features:
- Direct performance replacement
- For GM 2 Tower Coils Used From Mid 1980s To Late 1990s
- 80:1 turns ratio
- Lower Primary Resistance Produces High Voltage Output
- Works w/Stock Ignition As Well As MSD Ignitions
- CARB E.O. Approved
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)
from
$134.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Energy Suspension – Tie Rod Dust Boot (Part No.9.13102G)
from
$5.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)
from
$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Energy Suspension – Tie Rod Dust Boot (Part No.9.13101G)
from
$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Energy Suspension – Control Arm Bushing Set (Part No.3.3171G)
from
$57.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – Control Arm Bushing Set (Part No.3.3156G)
from
$116.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – Control Arm Bushing Set (Part No.3.3132R)
from
$154.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
B & M – Tork Master 2400 (Part No.20404)
from
$339.99
Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
B & M – Tork Master 2400 (Part No.70418)
from
$429.99
Torque Converter – Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) APPLICATION: Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) The Tork Master is B&M’s lowest cost pe
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
B & M – Torque Converter, Nitrous Holeshot 3000 (Part No.20481)
from
$766.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 2800-3200 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
Energy Suspension – Control Arm Bushing Set (Part No.3.3132G)
from
$154.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – Control Arm Bushing Set (Part No.3.3169G)
from
$59.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – Control Arm Bushing Set (Part No.3.3156R)
from
$111.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Popular 1988 Pontiac Grand Prix Performance and Racing Products Categories
1988 Pontiac Grand Prix Performance and Racing Products
You count on your 1988 Pontiac Grand Prix to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 16 Performance and Racing Products ranging in price from $5.99 to $766.99, you’re sure to find everything you need for your 1988 Pontiac Grand Prix.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 8 different brands like K&N, Energy Suspension, and Accel. 1988 Pontiac Grand Prix Performance and Racing Products start as low as $5.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 183 extensive product reviews on 1988 Pontiac Grand Prix Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are GM 86-99 Dis Supercoil with 2.2 stars and Unilite Ignition Module with 5.0 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1988 Pontiac Grand Prix below to get started!
Top-Rated Performance and Racing Products Brands For Your 1988 Pontiac Grand Prix
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1988 Pontiac Grand Prix running right for years to come. In our inventory you’ll find brands like K&N, Energy Suspension, Accel, and even more.
Popular K&N Performance and Racing Products
You’ll find popular K&N brand products across Performance Oil Filters. All are waiting to get your 1988 Pontiac Grand Prix back on the road. Some of the top-rated K&N products in these categories are:
from
$17.99
(29)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
FAQs for 1988 Pontiac Grand Prix Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1988 Pontiac Grand Prix?
Out of 16 Performance and Racing Products for the 1988 Pontiac Grand Prix, the most popular in our inventory are:
What are the top-rated 1988 Pontiac Grand Prix Performance and Racing Products?
Top-rated Performance and Racing Products for your 1988 Pontiac Grand Prix based on customer reviews/ratings are:
from
$85.29
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”
from
$154.99
(3)
50 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Moderate Sound
“Muffler was delivered on time and fit my 1994 Ford Ranger perfectly, and was easy to install (once I got the old one off). The whole muffler felt ‘sol”
