1988 Jeep Grand Wagoneer Belts and Hoses
More 1988 Jeep Grand Wagoneer Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1988 Jeep Grand Wagoneer, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1988 Jeep Grand Wagoneer Belts and Hoses
Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25476)
from
$29.49
Product Features:
See More
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.21660)
from
$23.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – V-Belt Idler/Tensioner Pulley; Steel, 94mm Dia., 16.4mm Width, Grooves (Part No.89020)
from
$24.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 90mm Dia., 39.5mm Width, Smooth (Part No.89048)
from
$46.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Omix – Radiator Hose Clamp (Part No.17115.01)
from
$6.79
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.
Product Features:
See More
Product Features:
- OE Style
- Direct Fit
- Stainless Steel
- Sold Individually
- Limited 5 Year Warranty
Gates – Premium Molded Coolant Hose (Part No.22038)
from
$11.79
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5" Long, .97" Diameter (Part No.A71651)
from
$20.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 6.75" Long, .75" Diameter (Part No.B70553)
from
$14.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Crown Auto Jeep Replacmnt – 6 Groove, 3.95 Inch Diameter, Black, Steel (Part No.J3239821)
from
$78.99
Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.
Product Features:
See More
Product Features:
- Plastic And Metal Construction
- Meets Standards For Quality
- Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
- Easy Installation
Dorman – Idler/Tensioner Pulley: Specific Fit, Steel, 90.2 mm Diameter (Part No.419-672)
from
$27.49
This replacement accessory drive belt idler pulley has been engineered to match the function and performance of the original pulley on select vehicle years, makes and models, properly restoring critical vehicle operations.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt idler pulley matches the fit and function of the original equipment pulley on specified vehicles
- Restores performance – fixes a failed, squealing or groaning noise from a worn idler pulley
- Application specific – reverse engineered from the original design on certain vehicle years, makes and models
- Trustworthy quality – backed by team of engineers and quality specialists in the United States
Dayco – Dayco, Acc. Belt Idler Pulley (Part No.G6020926341DAY)
from
$19.49
The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application.
- Precision bearing
- OE High quality pulley assembly
- Durable long life performance.
Yukon Gear – Seal Puller Tool (Part No.56063)
Driveworks – Automotive V-Belt, Driveworks (Part No.42315)
from
$5.99
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Dayco – Bottom Cog V-Belt; 42.25 Inch Long, Exact Fit Premium Quality (Part No.15423)
from
$15.49
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Dayco – Bottom Cog V-Belt; 54 Inch Long, Exact Fit Premium Quality (Part No.15540)
from
$20.79
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Dayco – Bottom Cog V-Belt; 50.5 Inch Long, Exact Fit Premium Quality (Part No.15505)
from
$25.49
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
Dorman – Help – Carburetor Pre-Heater Hose – 2 In. X 28 In. – Paper/ Aluminum (Part No.96034)
from
$15.99
This HVAC control duct hose is designed to match the fit and function of the original hose on specified vehicles, and is engineered for durability and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this HVAC control duct hose is designed to match the fit and function of the original hose on specified vehicles
- Restores functionality – reliable replacement for an original hose that has failed due to heat or vibration
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Gates – Emission Control Duct Hose (Part No.28095)
from
$12.99
Product Features:
See More
- Aluminum polyester construction for economy
- Black fiberglass aluminum for greater strength and durability
- Completely +exible and easily bent, yet retains shape after forming
- Resists heat, cold, oil and water
- Temperature Range: -40 Deg. F to 400 Deg. F (-40 Deg. C to +204 Deg. C)
- Temperature rating: -40 Deg. F to 400 Deg. F (-40 Deg. C to +204 Deg. C).
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21" Long, 1.50" Diameter (Part No.E70755)
from
$21.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.20573)
from
$27.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25808)
from
$54.99
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.625" Inside Diameter (Sold by foot) (Part No.28411)
from
$1.49
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14" Long, 1.56" Diameter (Part No.C70670)
from
$16.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13" Long, 1.50" Diameter (Part No.C70295)
from
$25.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Popular 1988 Jeep Grand Wagoneer Belts and Hoses Categories
1988 Jeep Grand Wagoneer Belts and Hoses
You count on your 1988 Jeep Grand Wagoneer to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 33 Belts and Hoses ranging in price from $3.99 to $79.99, you’re sure to find everything you need for your 1988 Jeep Grand Wagoneer.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 10 different brands like Dayco, Omix, and Imperial. 1988 Jeep Grand Wagoneer Belts and Hoses start as low as $3.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 33 extensive product reviews on 1988 Jeep Grand Wagoneer Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Carburetor Pre-Heater Hose – 2 In. X 28 In. – Paper/ Aluminum with 3.0 stars and V-Belt Idler/Tensioner Pulley; Steel, 94mm Dia., 16.4mm Width, Grooves with 5.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1988 Jeep Grand Wagoneer below to get started!
Top-Rated Belts and Hoses Brands For Your 1988 Jeep Grand Wagoneer
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1988 Jeep Grand Wagoneer running right for years to come. In our inventory you’ll find brands like Dayco, Omix, Imperial, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 1988 Jeep Grand Wagoneer back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1988 Jeep Grand Wagoneer, and some of our most reviewed Dayco parts include:
from
$21.99
(5)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21" Long, 1.50" Diameter
Upper Radiator Hoses
from
$28.49
(3)
Flex Radiator Hoses; EPDM Rubber, 22 Inch Long, 1.5 Inch Inner Dia.
Lower Radiator Hoses
FAQs for 1988 Jeep Grand Wagoneer Belts and Hoses
What are the most purchased Belts and Hoses for the 1988 Jeep Grand Wagoneer?
Out of 33 Belts and Hoses for the 1988 Jeep Grand Wagoneer, the most popular in our inventory are:
from
$25.99
(1)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13" Long, 1.50" Diameter
Upper Radiator Hoses
What are the top-rated 1988 Jeep Grand Wagoneer Belts and Hoses?
Top-rated Belts and Hoses for your 1988 Jeep Grand Wagoneer based on customer reviews/ratings are:
from
$15.99
(2)
Carburetor Pre-Heater Hose – 2 In. X 28 In. – Paper/ Aluminum
“Perfect fit – excellent quality.”
from
$24.99
(1)
V-Belt Idler/Tensioner Pulley; Steel, 94mm Dia., 16.4mm Width, Grooves
“I had left a previous review that the tensioner pulley was defective and began squealing.
It was not the pulley – it was the belt. Evidently if ther”
from
$25.49
(1)
Bottom Cog V-Belt; 50.5 Inch Long, Exact Fit Premium Quality
“No problem fit perfectly”
