1988 Chevrolet Cavalier Performance and Racing Products
More 1988 Chevrolet Cavalier Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1988 Chevrolet Cavalier, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1988 Chevrolet Cavalier Performance and Racing Products
Accel – GM 86-99 Dis Supercoil (Part No.140017)
from
$72.99
Re-engineered to be the only true performance AC/Delco style DIS coil. “”Raised Dome”” construction, section bobbin technology, highly specialized silicone magnetic steel core, optimized windings, resistance, and turns ratio result in higher energy and voltage outputs, and longer dwell. Compatible with OE computer controlled ignition systems as well as Crane or MSD capacitive discharge DIS ignition systems. Brass contact increases energy transfer and resists corrosion better than aluminum. High dielectric strength “”ACCEL Yellow”” over molded housing. Packaged as single unit: 4 cyls require 2 coils, 6 cyls require 3 coils and 8 cyls require 4 coils.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP Dr-39
- MSD 8224
- Resist Corrosion
MSD Ignition – Coil; GM External HEI Coil; High Performance (Part No.8226)
from
$71.99
Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.
Product Features:
See More
Product Features:
- Direct performance replacement for GM dual connector coil
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Works w/Stock Ignition As Well As MSD Ignitions
Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)
from
$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Energy Suspension – Tie Rod Dust Boot (Part No.9.13102G)
from
$5.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-1001)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-7000)
from
$14.99
K&N Cartridge Oil Filters are designed to satisfy the needs of racers and engine builders as well as the average vehicle owner who wants the best oil filter available. K&N cartridge oil filters trap harmful contaminants while the filter’s construction allows for high oil flow rates. All K&N oil filters are manufactured to meet stringent engineering standards.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
Edelbrock – Signature Series Valve Covers: Chevrolet 2.8L, 60░ V6, 1982-93, Chrome Steel (Part No.4488)
from
$119.99
The Edelbrock #4488 Signature Series Valve Covers are designed for Chevrolet 2.8L 60 Deg V6 ’82-93 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.
Product Features:
See More
Product Features:
- Chevrolet 2.8L, 60 Degree, 1982-93
- Short
- Chrome Steel
- Set Of Two
- Rubber Grommets For Breather
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mr. Gasket – Thermocap Radiator Cap (Part No.2470R)
from
$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.
Product Features:
See More
Product Features:
- Indicates coolant temperature
- Helps prevent coolant injuries
- Fahrenheit and centigrade readings
- Color-coded temperature ranges
- Integrated coolant reclamation valve
- Improves under-hood appearance
- Chromed crown with a colored trim ring
Hypertech – Street Runner Power Chip (Part No.151411)
from
$204.49
Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.
Product Features:
See More
Product Features:
- Designed For Daily Street Driving
- For Unmodified Vehicles w/Stock Thermostat
- Controls Engines Air/Fuel Ratio
- Controls Spark Advance For Max Power
- Potential Gas Mileage Improvements
- No Wiring Or Soldering Required
- Installs In Less Than 30 Minutes
Hypertech – Street Runner Power Computer Chip (Part No.123421)
from
$204.49
Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.
Product Features:
See More
Product Features:
- Designed For Daily Street Driving
- For Unmodified Vehicles w/Stock Thermostat
- Controls Engines Air/Fuel Ratio
- Controls Spark Advance For Max Power
- Potential Gas Mileage Improvements
- No Wiring Or Soldering Required
- Installs In Less Than 30 Minutes
- Product might not be available in all states due to local laws.
Hypertech – Street Runner Power Chip (Part No.11821)
from
$158.89
Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.
Product Features:
See More
Product Features:
- Designed For Daily Street Driving
- For Unmodified Vehicles w/Stock Thermostat
- Controls Engines Air/Fuel Ratio
- Controls Spark Advance For Max Power
- Potential Gas Mileage Improvements
- No Wiring Or Soldering Required
- Installs In Less Than 30 Minutes
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1624)
from
$24.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
- Not intended for use in emission controlled vehicles.
Hypertech – Street Runner Power Computer Chip, 4 Speed Model Only (Part No.11781)
from
$158.89
Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.
Product Features:
See More
Product Features:
- Designed For Daily Street Driving
- For Unmodified Vehicles w/Stock Thermostat
- Controls Engines Air/Fuel Ratio
- Controls Spark Advance For Max Power
- Potential Gas Mileage Improvements
- No Wiring Or Soldering Required
- Installs In Less Than 30 Minutes
- Product might not be available in all states due to local laws.
Hypertech – ThermoMaster Power Chip (Part No.11772)
from
$168.89
Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).
Product Features:
See More
Product Features:
- Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
- Controls Engines Air/Fuel Ratio
- Controls Spark Advance For Max Power
- Potential Gas Mileage Improvements
- No Wiring Or Soldering Required
- Installs In Less Than 30 Minutes
Hypertech – Street Runner Power Chip (Part No.128421)
from
$204.49
Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.
Product Features:
See More
Product Features:
- Designed For Daily Street Driving
- For Unmodified Vehicles w/Stock Thermostat
- Controls Engines Air/Fuel Ratio
- Controls Spark Advance For Max Power
- Potential Gas Mileage Improvements
- No Wiring Or Soldering Required
- Installs In Less Than 30 Minutes
- Product might not be available in all states due to local laws.
Hypertech – ThermoMaster Power Chip (Part No.121412)
from
$214.49
Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).
Product Features:
See More
Product Features:
- Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
- Controls Engines Air/Fuel Ratio
- Controls Spark Advance For Max Power
- Potential Gas Mileage Improvements
- No Wiring Or Soldering Required
- Installs In Less Than 30 Minutes
Hypertech – Street Runner Power Computer Chip (Part No.122411)
from
$204.49
Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.
Product Features:
See More
Product Features:
- Designed For Daily Street Driving
- For Unmodified Vehicles w/Stock Thermostat
- Controls Engines Air/Fuel Ratio
- Controls Spark Advance For Max Power
- Potential Gas Mileage Improvements
- No Wiring Or Soldering Required
- Installs In Less Than 30 Minutes
- Product might not be available in all states due to local laws.
B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)
from
$665.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 3400-3800 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
B & M – Torque Converter, Nitrous Holeshot 3000 (Part No.20481)
from
$766.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 2800-3200 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
Mr. Gasket – Starter Motor Heat Shield (Part No.3678)
from
$43.99
Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.
Product Features:
See More
Product Features:
- Designed to prevent starter overheat due to extreme exhaust temperature
- Heat resistant material sandwiched between 2 aluminum plates
- Protects Starter From High Temperatures
- Made Of 2 Sheets Of Aluminum Heat Resistant Center
- Natural Finish
Popular 1988 Chevrolet Cavalier Performance and Racing Products Categories
1988 Chevrolet Cavalier Performance and Racing Products
You count on your 1988 Chevrolet Cavalier to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 20 Performance and Racing Products ranging in price from $5.99 to $766.99, you’re sure to find everything you need for your 1988 Chevrolet Cavalier.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 10 different brands like K&N, Energy Suspension, and MSD Ignition. 1988 Chevrolet Cavalier Performance and Racing Products start as low as $5.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 417 extensive product reviews on 1988 Chevrolet Cavalier Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are GM 1984-95 Remote Supercoil with 3.9 stars and GM 86-99 Dis Supercoil with 2.2 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1988 Chevrolet Cavalier below to get started!
Top-Rated Performance and Racing Products Brands For Your 1988 Chevrolet Cavalier
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1988 Chevrolet Cavalier running right for years to come. In our inventory you’ll find brands like K&N, Energy Suspension, MSD Ignition, and even more.
Popular K&N Performance and Racing Products
You’ll find popular K&N brand products across Performance Oil Filters. All are waiting to get your 1988 Chevrolet Cavalier back on the road. Some of the top-rated K&N products in these categories are:
from
$17.99
(29)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
from
$17.99
(47)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
FAQs for 1988 Chevrolet Cavalier Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1988 Chevrolet Cavalier?
Out of 20 Performance and Racing Products for the 1988 Chevrolet Cavalier, the most popular in our inventory are:
What are the top-rated 1988 Chevrolet Cavalier Performance and Racing Products?
Top-rated Performance and Racing Products for your 1988 Chevrolet Cavalier based on customer reviews/ratings are:
from
$85.29
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”
