1987 Ford LTD Crown Victoria Belts and Hoses
More 1987 Ford LTD Crown Victoria Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1987 Ford LTD Crown Victoria, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1987 Ford LTD Crown Victoria Belts and Hoses
Driveworks – Poly Rib Belt Serpentine Belt; 99.02 Long, 6 Rib Count (Part No.33009)
from
$4.99
Dayco engineered to conform to high mileage, worn or misaligned drives without a sacrifice in quiet, long-lasting performance. Constructed with Aramid reinforced EPDM compounds, it delivers more than OE required quality… it delivers the solution to troublesome drive problems. Dayco Poly-Rib Belts meet or exceed SAE J1459 and SAE J2432 specifications.
Product Features:
See More
Product Features:
- Aramid noise resistant fibers embedded in the rubber make this belt run quieter in worn or misaligned pulleys
- No-Noise Advanced Design EPDM rubber compound for quiet extended life
Dayco – Bottom Cog V-Belt; 33 Inch Long, Exact Fit Premium Quality (Part No.09330)
from
$12.99
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 15 Inch Length (Part No.88351)
from
$25.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Coolant Hose (Part No.20662)
from
$19.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 17" Long, 1.50" Diameter (Part No.D71528)
from
$22.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 13 Inch Length (Part No.88357)
from
$27.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 7 Inch Length (Part No.87628)
from
$11.79
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Serpentine Idler/Tensioner Pulley; Polymer, 90mm Dia., 31mm Width, Smooth (Part No.89001)
from
$20.79
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Driveworks – Poly Rib Belt Serpentine Belt; 50 Long, 6 Rib Count (Part No.500K6)
from
$17.49
This Driveworks v-belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks v-belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
- Meets OEM requirements
Driveworks – Poly Rib Belt Serpentine Belt; 49.5 Long, 6 Rib Count (Part No.495K6)
from
$24.79
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Gates – Micro-V« Serpentine Drive Belt (Part No.K060505)
from
$31.99
Product Features:
See More
- Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
- EPDM rubber constructions resist cracking on the rib surface
- Meets or exceeds all specifications from the Original Equipment Manufacturer
- Tensioner Replacement is Recommended (if equipped)
Yukon Gear – Seal Puller Tool (Part No.56063)
Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25307)
from
$39.99
Product Features:
See More
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18.50" Long, 1.50" Diameter (Part No.E71303)
from
$18.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – DriveAlign½ Belt Drive Idler/Tensioner Pulley (Part No.38001)
from
$32.99
Product Features:
See More
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter (Part No.900052A)
from
$33.49
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the largest original equipment part suppliers in the world to ensure proper form, fit, and performance
- Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance
- Installation instructions included.
Dorman – Idler Pulley (Part No.G6011370309DOR)
from
$18.86
(Pulley Only) Dorman’s Belt Tensioner Pulley is engineered to maintain tension on the serpentine belt for the life of the belt–thereby keeping the alternator charging, the water pump running, and the power steering pump and A/C compressor operating properly. They feature a high-quality double-sealed bearing to resist damage from contaminants. Replacement prevents belt slip and eliminates squeak, squeal or groaning noise associated with a worn belt tensioner pulley.
Product Features:
See More
Product Features:
- Steel or plastic construction for long-lasting durability against heat, shock and corrosion
- Replacement stops squeak, squeal or groaning noise associated with a worn Belt Tensioner Pulley
- Direct replacement for a proper fit every time
- Vehicle try-on testing and rigorous materials testing to ensure high-quality performance
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25484)
from
$24.99
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Popular 1987 Ford LTD Crown Victoria Belts and Hoses Categories
1987 Ford LTD Crown Victoria Belts and Hoses
You count on your 1987 Ford LTD Crown Victoria to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 32 Belts and Hoses ranging in price from $4.99 to $79.99, you’re sure to find everything you need for your 1987 Ford LTD Crown Victoria.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 9 different brands like Dayco, Driveworks, and Imperial. 1987 Ford LTD Crown Victoria Belts and Hoses start as low as $4.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 286 extensive product reviews on 1987 Ford LTD Crown Victoria Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Curved Radiator Hoses: EPDM Rubber, Standard Duty, 17" Long, 1.50" Diameter with 5.0 stars and Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 15 Inch Length with 1.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1987 Ford LTD Crown Victoria below to get started!
Top-Rated Belts and Hoses Brands For Your 1987 Ford LTD Crown Victoria
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1987 Ford LTD Crown Victoria running right for years to come. In our inventory you’ll find brands like Dayco, Driveworks, Imperial, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 1987 Ford LTD Crown Victoria back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1987 Ford LTD Crown Victoria, and some of our most reviewed Dayco parts include:
from
$20.79
(41)
Serpentine Idler/Tensioner Pulley; Polymer, 90mm Dia., 31mm Width, Smooth
Belt Tensioner Pulleys
from
$26.99
(27)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5.50" Long, .63" Diameter
Heater Hoses
FAQs for 1987 Ford LTD Crown Victoria Belts and Hoses
What are the most purchased Belts and Hoses for the 1987 Ford LTD Crown Victoria?
Out of 32 Belts and Hoses for the 1987 Ford LTD Crown Victoria, the most popular in our inventory are:
What are the top-rated 1987 Ford LTD Crown Victoria Belts and Hoses?
Top-rated Belts and Hoses for your 1987 Ford LTD Crown Victoria based on customer reviews/ratings are:
from
$22.49
(1)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 17" Long, 1.50" Diameter
“Good solid replacement hose”
from
$25.99
(1)
Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 15 Inch Length
“Part number 304351 will not fit and cannot be adapted to fit a 1989 Lincoln Towncar (heater core to pipe) despite the website claim that it will. The”
