Name: Engine Valve Cover Gasket Set
Brand: FEL-PRO Performance
SKU: 1603
Price: 23.49 USD
Rating: 5.0 (1 reviews)

from

$23.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$385.99

Edelbrock #88563 Water Pump Pontiac 389-455 standard rotation black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooli

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
4.50 in. Block To Hub Height
Black Finish

from

$367.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched To Performer Intake PN[5486]
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$7.99

Spectre’s Harmonic Balancer Bolt Kit is designed to fit Chevrolet Small Block 265-400 V8 engines. This grade 8 bolt is 2-1/2 inches long, and features a plated finish for corrosion resistance. This kit also includes a security lock washer.

Product Features:

Fits Chevrolet Small Block 265-400 V8 engines
Features a corrosion resistant plated finish
Gold iridite finish
Grade 8 bolt, 7/16 inch-20 by 2-1/2 inches
Includes security lock washer

from

$67.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$21.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for repair applications
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$412.99

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
Designed for high performance street and race engines
Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
Additional clearance, up to 1.650″ O.D. valve spring

from

$26.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$566.99

Edelbrock part #21011 Performer intake manifold is designed for street 1955-86 small-block Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle respons

from

$587.99

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

from

$548.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$323.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$622.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$65.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$126.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
O.D.: 1.254″, I.D.: .880″
Single valve springs with damper
Approximately .490″ max lift at recommended installed height

from

$429.99

Torque Converter – Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) APPLICATION: Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) The Tork Master is B&M’s lowest cost pe

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$665.99

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

3400-3800 RPM
Small And Big Blocks
Serious Performance
Furnace Brazed
Fully Balanced

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$18.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$62.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
Not for OEM Hydraulic Roller-Lifter Camshaft Eng.

from

$97.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$157.99

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

3/8″ Diameter, 7.800″ Length
Magnum Pushrods for Small Block Chevy
One-piece .080″ wall chromemoly steel tubing
Heat-treated for extended durability and guide plate compatibility
Precision formed and reinforced pushrod end

from

$20.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Steel core gasket construction
Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
Not intended for use in emission controlled vehicles.

from

$17.99

Product Features:

For Small-Block Chevy
One Piece Configuration
Includes Front Cover Gasket & Front Seal
Includes Necessary Gaskets & Crankshaft Oil Seal
For Replacement Or Installation

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

1985 Pontiac Bonneville Performance Engines

More 1985 Pontiac Bonneville Performance Engines

Essential 1985 Pontiac Bonneville Performance Engines

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Edelbrock – Water Pump for Pontiac, Standard Rotation in Black Finish (Part No.88563)

Edelbrock – Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire (Part No.5487)

Spectre – Chevrolet Small Block V8 Harmonic Balancer Bolt Kit (Part No.4699)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1016)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2900)

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Chevrolet Small Block w/ 3/8" Stud (Part No.19002-16)

Edelbrock – Intake Manifold Gasket for 1958-1986 Small-Block Chevy (Part No.7201)

Edelbrock – Performer Intake Manifold for 1955-86 Small-Block Chevy, Polished Finish (Part No.21011)

Competition Cams – THUMPR CAMSHAFT, SBC 1 EA (Part No.12-600-4)

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam for Oldsmobile 260-455 (Part No.42-222-4)

Competition Cams – CAM & LIFTER KIT, SBC 260H HIGH ENERGY HYD 1 KT (Part No.CL12-206-2)

Competition Cams – High Energy 212/212 Hydraulic Flat Cam K-Kit for Pontiac 265-455 (Part No.K51-230-3)

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)

B & M – Tork Master 2400 (Part No.70418)

B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1818)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1800)

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7800)

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7813)

Competition Cams – Magnum 7.800" Long, .080" Wall, 3/8" Diameter Pushrod Set (Part No.7513-16)

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Edelbrock – Front Timing Cover Gasket Set #6997 For Small-Block Chevy, With Front Seal (Part No.6997)

Mr. Gasket – Intake Manifold Bolts (Part No.6091)

Popular 1985 Pontiac Bonneville Performance Engines Categories

1985 Pontiac Bonneville Performance Engines

Performance Engines Brands To Make Your 1985 Pontiac Bonneville Last

Popular Spectre Performance Engines

Top 1985 Pontiac Bonneville Performance Engines from Mr. Gasket

FAQs for 1985 Pontiac Bonneville Performance Engines

What are the most purchased Performance Engines for the 1985 Pontiac Bonneville?

What are the top-rated 1985 Pontiac Bonneville Performance Engines?

More Popular Parts for All Makes