1985 Ford Bronco Drivetrains

Below you will find various in-demand Ford Drivetrains, components and accessories for your 1985 Bronco. Advance Auto Parts has popular Bronco parts like 4WD Components, Differentials, Drive Shafts and Axles and more. You’ll also find aftermarket and OEM Drivetrains for other Bronco model years including 1991, 1992, 1993, 1994, 1995, 1996, 2021, 2022, 2023 and more. Select a category of 1985 Ford Bronco Drivetrains below and start saving instantly.

Popular 1985 Ford Bronco Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

Differential Pinion Yokes

U-Joints

4WD Hubs

Transfer Case Adapter Gaskets

Transfer Case Gaskets

Rear Differential Cover Gaskets

Miscellaneous CV and U-Joint Parts

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Axle Shafts

Bearing Pullers

Locking Hub Spindle Nuts

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Locking Hub Service Kits

Axle Spindle Seals

U-Joint Centering Yokes

Differential Cover Bolts

Input Shaft Pilot Bearings

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Disc Kits

Differential Clutch Packs

Rear Axle Shaft Bearings

Differential Ring and Pinions

Stub Axles

U-Joint U-Bolt Kits

Differential Cases

Differential End Yokes

Differential Pinion Supports

Differential Lock Assemblies

Differential Air System Seal Housings

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Differential Lock Springs

Differential Carrier Bearing Adjusters

Rear Housing Cover Gaskets

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Drive Shaft Seals

Differential Seals

Complete Differentials

Bearing and Seal Overhaul Kits

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Pinion Shafts

Differential Carrier Bearing Shims

Axle U-Bolt Kits

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Automatic Transmission Differential Carrier Gaskets

Differential Housing O-Rings

Differential Side Gear Thrust Washers

Transfer Case Oil Drain Plugs

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Oil Pump Housing Seals

Axle Shaft Studs

Transfer Case Shift Fork Inserts

Differential Drive Pinion Gear Bearing Retainer Bolts

Differential Drive Pinion Oil Deflectors

Differential Carrier Bolts

Differential Pinion Gear Washers

Axle Shaft Snap Rings

Output Shaft Pilot Bearings

Spindle Washers

Axle Shaft Bearing Retainers

Differential Ring and Pinion Kits

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

Differential Lock Washers

Differential Clutch Pack Clips

Differential Lock Thrust Blocks

Differential Pinion Bearing Spacers

Axle Pinion Repair Sleeves

Differential Bearing Adjuster Nut Lock Bolts

Axle Housing Fill Plugs

Differential Carrier Bearing Races

Drive Shaft Pinion Yoke Washers

Essential Drivetrains for 1985 Ford Broncos

from

$269.99

Plain Silver aluminum pinion Supprt for 9″ Ford Daytona, HD 6061.

Product Features:

Fits Ford 9″ with 28 spline pinion
Larger inner pinion bearing reduces gear deflection under high load
Races installed
6061 aluminum

from

$9.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$13.99

Product Features:

O-ring for seal housing
Fits Dana Spicer 30 and AMC Model 35

from

$57.99

The components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of an axle of a vehicle or trailer. Check the leaf spring dimensions and other relevant application details to select the right type and size U-bolt kit for your needs.

Product Features:

Reliable hardware – the components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of a vehicle or trailer axle
Check fit – carefully review the dimensions of the leaf springs that will be used and other relevant application details to select the right type and size U-bolt kit for your needs
Durable construction – the components in this kit are engineered from quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$121.99

Yukon short yoke for Ford 9″ with 28 spline pinion and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. 4″ length. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″
28 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 30

from

$14.99

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

Pinion support o-ring
Fits Ford 9″

from

$9.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: springless; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$12.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$7.29

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.99

Product Features:

Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
0.030″ thick

from

$18.99

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations.
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

from

$11.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$1.99

Product Features:

Ford 7.5″, 8.8″ Ring Gear Bolt

from

$213.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits reverse rotation Dana Spicer 44
Straight axle only
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$80.49

Product Features:

FORD 9″ CLUTCH PACK KIT NEED ONE PER UNIT

from

$15.99

Driveworks wheel bearings are a direct replacement for original parts at a much more affordable cost. Each wheel bearing is engineered to meet or exceed OE specifications, and goes through intensive quality control inspections to ensure proper fitment. Manufactured using high-precision machinery and advanced heat treatment processes, these bearings are designed for maximum durability and extended periods of use under any driving condition. Specific to certain applications, Driveworks bearings have multi-lip seals built into the bearing for increased protection against invasive contaminants and premature wear.

Product Features:

Depending on the application, specified Driveworks wheel bearings have integrated encoder rings that automatically sync with the vehicle’s anti-lock braking system (ABS) upon successful installation
Engineered, manufactured, and tested to meet or exceed OE specifications
Integrated seal design improves contamination resistance for a longer bearing life
High performance grease is used to lubricate the inner raceway to ensure smooth operation, higher operating temperatures, and minimal noise
Manufactured from high quality steel to maximize durability under even the harshest driving conditions
Brand may vary by location

from

$94.49

Product Features:

BW1356 BEARING & SEAL KIT ALSO 1370 (W/O THE CENTER PLATE)

from

$324.99

Ring/Pinion Sets

from

$3.99

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

from

$71.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

Machined bodies to meet the tight tolerances
Forged and cast material to meet the performance requirement
Minimize the flash lines for less interference
Cleaning process induces compressive strength for increased performance
Machined and threaded holes for mounting ease
Rust preventative added for longer shelf life

from

$11.99

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications
Effective fix – restores a tight seal in the transfer case after original gasket fails
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$15.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$11.99

For U-Joints 375, 430, 434 & 498
Fits 1-1/8″ bearings

from

$13.49

This transfer case oil drain plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this transfer case oil drain plug matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

Upgrade your 1985 Ford Bronco with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1985 Ford Bronco, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your Bronco functioning at its best. At Advance Auto Parts, we offer a wide selection of 739 Drivetrains for the 1985 Ford Bronco, designed to meet your needs without breaking the bank. From 4WD Component replacements to Differentials upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1985 Ford Bronco at great prices. Our Drivetrains inventory for this model ranges from just $1.29 to $2,199.99, with an average price of $248.71. Our 739 Drivetrains in stock come from 22 trusted brands, so you’re sure to find the right part for your 1985 Ford Bronco without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1985 Ford Bronco, we stock popular OEM and aftermarket Drivetrains from top names like National, DriveWorks, Motive Gear, and more. National Drivetrains start at just $7.99 and boast an impressive 4.3 stars average rating from customers. DriveWorks and Motive Gear also bring quality to the table, with Drivetrains available starting at $4.79, and at an average 4.3 stars rating. With 3,516 customer reviews and counting, our 1985 Ford Bronco Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1985 Ford Bronco is always ready to roll. We’re committed to providing you with everything you need to keep your Bronco in top shape, all in one place. Start shopping confidently below for your 1985 Ford Bronco!

Best-Selling 4WD Components for 1985 Ford Broncos

Enhance the driving experience in your Ford with 2 quality 4WD Component components, starting at $116.99.

show more show less

from

$116.99

Black nylon reinforced fiberglass dial. Limited lifetime warranty. 19 spline, internal bolts. Chrome.

Product Features:

Black Nylon Reinforced Fiberglass Dial
Limited Lifetime Warranty

from

$204.99

Ultimate in style and service. Latest patented technology. Smooth operation. Limited lifetime warranty. 10 spline, 6 bolts. Chrome.

Product Features:

Ultimate In Style And Service
Latest Patented Technology
Smooth Operation
Limited Lifetime Warranty

Most Popular 1985 Ford Bronco Differentials

Customize your Ford with 608 Differentials products like Differential Oil, Rear Housing Cover Gaskets, and Rear Differential Cover Gaskets, all priced under $2,199.99.

show more show less

from

$7.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$9.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$126.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT BRG&SL FORD MSTR 8.8

from

$37.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$551.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!

from

$179.99

Product Features:

FRD 10BL 8.8 R/P 4.10A MG

from

$15.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$26.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$18.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$41.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$7.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$7.79

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$6.79

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$27.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$137.99

MASTER KIT FORD 8.8″

from

$6.99

from

$169.99

The National bearing & seal kit includes all the components required to complete the repair.

Product Features:

COMPLETE SOLUTION – Includes everything needed to complete the repair
STRONG AND DURABLE – Controlled heat treatment process for strength and durability
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Professional technicians know they can depend on National

from

$19.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$112.99

The National bearing & seal kit includes all the components required to complete the repair.

Product Features:

COMPLETE SOLUTION – Includes everything needed to complete the repair
STRONG AND DURABLE – Controlled heat treatment process for strength and durability
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Professional technicians know they can depend on National

from

$8.99

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$5.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$6.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

Top Picks for 1985 Ford Bronco Drive Shafts and Axles

Upgrade Ford Broncos with top-quality Drive Shafts and Axles parts, including 43 OEM and aftermarket selections for your 1985 model.

show more show less

from

$55.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

from

$13.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.99

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$22.99

Manufactured with premium-grade steel, National® cylindrical bearings are designed and engineered to meet OE specifications.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$44.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$21.49

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
COMPLETE MOUNT

from

$15.99

Depending on the application, specified Driveworks wheel bearings have integrated encoder rings that automatically sync with the vehicle’s anti-lock braking system (ABS) upon successful installation
Engineered, manufactured, and tested to meet or exceed OE specifications
Integrated seal design improves contamination resistance for a longer bearing life
High performance grease is used to lubricate the inner raceway to ensure smooth operation, higher operating temperatures, and minimal noise
Manufactured from high quality steel to maximize durability under even the harshest driving conditions
Brand may vary by location

from

$14.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$8.49

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 deg. F to 225 deg. F / -40 deg. C to 107 deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$7.99

Wheel Lug Stud

from

$52.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1559TV axle bearing and seal kit, TorringtonBrand, 2.530″ OD, 1.620″ ID This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.530″ O.D.
1.620″ I.D.

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$14.29

Design type: springless; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$5.99

AXLE STUD , 58MM X M14-2.0 .

from

$7.99

Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.

Product Features:

Rear axle seal
2.530″ O.D.

from

$10.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Fill plug
Fits Ford 9″

from

$119.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$30.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$111.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Tapered axle bearing and seal kit, 3.150″ OD, for 9″ Ford. This axle bearing & seal kit services one side only.

Product Features:

Axle bearing and seal kit for Ford 9″ rear
Includes axle bearing and seal
Tapered roller design
3.150″ O.D.
1.562″ I.D.
Services one side

from

$67.99

Product Features:

Axle bearing retainer for Ford 9″
Fits large bearing applications
1/2″ bolt holes
3 1/2″ x 2 3/8″ bolt pattern

from

$25.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

RIGHT TYPE — Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS — Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$4.99

Dana 28, Dana 30, Model 35-Reverse, Dana 44, Dana 50 INside axle snap ring (next to side gear).

Product Features:

Inner axle snap ring for Dana Spicer 28, 30, 44 and 50
Intalls next to side gear

from

$146.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1330 U/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 30 and 44
26 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.062″ cap diameter
Strap style

from

$14.99

Outside seal (included in TK set20).Yukon Mighty seal.

Product Features:

Outer axle seal
Works with Set20 bearing

In-Demand Transfer Cases for 1985 Ford Broncos

Select from 27 premium Transfer Cases parts for your 1985 Ford Bronco, with prices ranging from $4.99 to $171.99.

show more show less

from

$17.99

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$20.49

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$36.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$11.99

Design type: spring loaded; single-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$13.99

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$7.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$32.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.99

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications
Effective fix – restores a tight seal in the transfer case after original gasket fails
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$11.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$4.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$26.99

Meets or exceeds all original equipment specifications
Application specific, providing unsurpassed quality for a seal you can trust
Validated for fit, form, and function
Engineered for the sealing repair environment
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$31.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$22.99

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$13.49

Direct replacement – this transfer case oil drain plug matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$9.99

Design type: springless; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$16.99

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$13.99

TCaseInputShaftSeal

from

$26.49

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$171.99

TCaseBrg-SealKit

from

$153.99

TCaseBrg-SealKit

from

$62.99

The FAG repair sleeve is a precision element that provides additional sealing for damaged shafts. Made of heat-treated stainless steel, the FAG repair sleeve signifcantly increases the life of the shaft and prevents premature wear. Since no shaft removal or machining is required during the repair, the repair sleeve is a cost effective repair solution to protect damaged surfaces.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$52.99

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$34.99

TCaseGasketSealKit

from

$21.29

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Most Sold 1985 Ford Bronco Universal Joints

Explore our best-selling Ford parts for the 1985 Bronco among 45 OEM and aftermarket options starting from $4.19.

show more show less

from

$11.99

For U-Joints 375, 430, 434 & 498
Fits 1-1/8″ bearings

from

$6.79

Universal Joint – Brute Force

from

$5.59

Universal Joint

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$31.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$29.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$40.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$55.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$29.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$16.49

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$42.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$25.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$6.99

This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.89

Universal Joint

from

$7.89

Universal Joint

from

$4.59

Universal Joint

from

$24.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$5.49

Universal Joint – Brute Force

from

$30.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$105.99

Machined bodies to meet the tight tolerances
Forged and cast material to meet the performance requirement
Minimize the flash lines for less interference
Cleaning process induces compressive strength for increased performance
Machined and threaded holes for mounting ease
Rust preventative added for longer shelf life

Top-Rated Drivetrains Brands For Your 1985 Ford Bronco

Shop for the best-rated brands offering Drivetrains and other products for your 1985 Ford Broncos. Below you’ll find some of our best rated Drivetrains from National, DriveWorks, and Motive Gear, and more. Drivetrains from these brands that fit a 1985 Bronco start at just $4.79 and are rated as high as 4.3 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular National 1985 Ford Bronco Drivetrains

When it comes to maintaining or upgrading your 1985 Ford Bronco, using quality Drivetrains is essential to ensure durability and a perfect fit. National ticks all of those boxes. We offer a wide selection of National Drivetrains, specifically designed for the 1985 Ford Bronco. With over 3 National brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $7.99, with an average price of just $13.32. Plus, with over 20 customer reviews and an average rating of 4.3 stars, you can trust that our National Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $13.99

(9)

Bearing

“as advertised”

from $7.99

(4)

Bearing Race

“Goes with M88010 bearing cup. Application was the pinion bearing race for a Ford 9 Inch on a 1957 Ford F-100.”

from $17.99

(7)

Multi-Purpose Bearing

“National bearings amazingly made in USA. Did the job.”

Popular DriveWorks 1985 Ford Bronco Drivetrains

DriveWorks auto parts is one of the highest quality Drivetrain brands in the market. Any 1985 Ford Bronco owner should feel confident when installing genuine DriveWorks parts in their vehicle. To ensure the best fit and performance for your 1985 Bronco, Advance Auto Parts carries a full inventory of 3 DriveWorks Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these DriveWorks Drivetrains range from $4.79 to $31.99, plus, with more than 67 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $31.99

(65)

Universal Joint

“Quality ujoint at a good price”

from $4.79

(1)

Oil Seal

“93 Dodge Ram stub axle to hub dust seal, worked great!”

from $5.99

(1)

Oil Seal

“This product looks very well made (compared to stock item it replaced).”

FAQs for 1985 Ford Bronco Drivetrains

Which Drivetrains are best-sellers for 1985 Ford Broncos?

Out of 739 Drivetrains that fit 1985 Ford Broncos, the following parts are the top sellers:

Axle Housing Cover Gasket Rectangular Shaped, 10 Bolt Hole Gasket (5782406) – $15.99
Universal Joint (10265720) – $31.99
Non-Greaseable Super Strength Universal Joint (10087058) – $29.99

What’s the price range for 1985 Ford Bronco Drivetrains?

Drivetrain prices for the 1985 Ford Bronco start at $1.29 and go up to $2,199.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1985 Ford Bronco?

The average price for Drivetrains for the 1985 Ford Bronco is $248.71. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford Bronco model years?

Yes, we currently carry Drivetrains for 33 model years of Ford Broncos between 1966 and 2025. Drivetrains are bought most frequently for the following model years: 2023, 2022, 2021, 1996, 1995, 1994, 1993, 1992, and 1991.

What are the cheapest Drivetrains for my 1985 Ford Bronco?

The cheapest 1985 Ford Bronco Drivetrains we carry in stock are:

Differential Ring Gear Bolt (10282257) – $1.29
Ring Gear Bolt (19640279) – $1.99
Ring Gear Bolt (20520509) – $1.99
Differential Ring Gear Bolt (10282436) – $1.99
Differential Cross Shaft (10282201) – $2.99

What are the top-rated Drivetrains that fit the 1985 Ford Bronco?

Out of 3,516 reviews by customers, our 1985 Ford Bronco Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1985 Ford Bronco and their top-rated products:

Universal Joints
- Universal Joint (5270138) – $6.79
- Universal Joint (5270057) – $5.59
- Universal Joint U-Bolt Kit (10086976) – $11.99
4WD Components
- Universal Joint (5270138) – $6.79
- Universal Joint (5270057) – $5.59
- Universal Joint U-Bolt Kit (10086976) – $11.99
Spindles
- Universal Joint (5270138) – $6.79
- Universal Joint (5270057) – $5.59
- Universal Joint U-Bolt Kit (10086976) – $11.99

What types of Drivetrains do you sell for my 1985 Ford Bronco?

As of 11/2/25, these are some of the most in-demand types of Drivetrains for a 1985 Ford Bronco:

Can I get help with 1985 Ford Bronco Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford Bronco Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford Bronco Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1985 Ford Bronco Drivetrains

Yukon Gear – Silver Aluminum Pinion Supprt For 9" Ford Daytona (Part No.32037)

National – Bearings (Part No.15245)

Yukon Gear – O-Ring For Dana 30 & Model 35 Zip Locker Seal Housing (Part No.34005)

Dorman – U-Bolt Repair Kit – Reliable hardware (Part No.929-733)

Yukon Gear – Short Yoke For Ford 9" With 28 Spline Pinion And A 1310 U/Joint Size (Part No.41054)

Yukon Gear – Replacement Cover Gasket For Dana 30 (Part No.23003)

Yukon Gear – O-Ring For 9" Ford (Part No.30028)

National – Multi-Purpose Seal (Part No.341022)

Motive Gear – Differential Pinion Seal (Part No.7044NA)

Dorman – Spindle Washer – I.D. 1 In.-5/8 In. O.D. 2-1/2 In. Thickness 7/64 In. (Part No.618-041.1)

Yukon Gear – Dana 44, Ford 8" / 9", And Model 20 Side Gear Thrust Washer Replacement (Part No.33283)

Valvoline – Flex Fill Transmission & Differential Gear Oil: Full Synthetic 75W-90, 1 Quart (Part No.889785)

Driveworks – Taper Bearing Cone (Part No.S-M-88048)

Motive Gear – Ring Gear Bolt (Part No.D5AZ4216A)

Yukon Gear – Pinion Install Kit For Dana 44 Reverse Rotation Differential (Straight Axle, Not IFS) (Part No.13026)

Motive Gear – Differential Clutch Pack (Part No.F9-CPK)

Driveworks – Wheel Bearing: Direct Fit, 1 Piece (Part No.S-5707)

Motive Gear – Transfer Case Bearing and Seal Kit (Part No.T1356R)

USA Standard Gear – Ring/Pinion Sets (Part No.36347)

Yukon Gear – Dana 25 / 27 / 30 / 36 / 44 / 53 Pinion Nut Washer Replacement (Part No.33163)

MOOG Driveline Products – Double Cardan CV H Yoke (Part No.647)

Dorman – Transfer Case Gasket (Part No.917-522)

National – Bearing Race (Part No.HM88610)

Yukon Gear – Cover Bolt For Ford 7.5", 8.8" & 9.75" (Part No.33554)

MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.534-10)

Dorman – Oil Drain Plug Standard M22-1.50, Head Size 30mm (Part No.090-061CD)

Motive Gear – Differential Pinion Shim Kit (Part No.1100)

Yukon Gear – Dana 30 & Dana 44 Power Lok Bolt, Left Hand, & 8.75" Chrysler & 55P (Part No.33234)

Milemarker – MileMarker Street Master; Manual Hub (Part No.302)

Milemarker – MileMarker Supreme; Manual Hub (Part No.104)

National – Bearing Race (Part No.M88010)

Felpro – Differential Carrier Gasket Oval Shaped 10 Bolt Hole Gasket (Part No.RDS 55074)

Motive Gear – Differential Pinion Shim Kit (Part No.1100)

Motive Gear – Differential Master Bearing Kit – Koyo (Part No.R8.8RMK)

National – Shaft Repair Sleeve (Part No.99199)

Powertrax – No-Slip Traction System (Part No.9206902800)

Motive Gear – Differential Ring and Pinion (Part No.F8.8-410A)

Felpro – Axle Housing Cover Gasket Rectangular Shaped, 10 Bolt Hole Gasket (Part No.RDS 55341)

Driveworks – Tapered Cone/Cup Wheel Bearing Set (Part No.S-A-35)

National – Multi-Purpose Bearing (Part No.A-37)

Dorman – Differential Cover (Part No.697-702)

Felpro – Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (Part No.RDS 6629)

National – Bearing Race (Part No.LM102910)

Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)

National – Multi-Purpose Bearing (Part No.A-36)

Motive Gear – Differential Master Bearing Kit – Timken (Part No.R8.8RMKT)

Motive Gear – Differential Pinion Nut (Part No.379570S)

National – Axle Differential Bearing & Seal Kit (Part No.RA-311)

National – Tapered Roller Bearing Cone (Part No.LM501349)

Dorman – Differential Yoke including Seal and Pinion Nut (Part No.697-507)

National – Axle Differential Bearing & Seal Kit (Part No.RA-311MK)

Motive Gear – Differential Carrier Shim Kit (Part No.1101)

Driveworks – Oil Seal (Part No.S-3604)

Driveworks – Oil Seal (Part No.S-7044NA)

Spicer – Universal Joint (Part No.5-760X)

National – Bearing (Part No.M88048)

National – Multi-Purpose Seal (Part No.8835S)

National – Wheel Bearing (Part No.5707)

National – Drive Shaft Center Support Bearing (Part No.HB-88107-A)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

Driveworks – Wheel Bearing: Direct Fit, 1 Piece (Part No.S-5707)

National – Multi-Purpose Seal (Part No.470672)

National – Multi Purpose Seal (Part No.7412S)

Yukon Gear – Wheel Lug Stud (Part No.33571)

Yukon Gear – R1559Tv Rear Axle Bearing And Seal Kit (Part No.10001)

Yukon Gear – C/Clip (Part No.33083)

National – Multi-Purpose Seal (Part No.710043)

Yukon Gear – Axle Stud , 58Mm X M14-2.0 (Part No.33557)

Yukon Gear – Axle Seal, For 1559 Or 6408 Bearing (Part No.30201)

Yukon Gear – Fill Plug For Ford 9", 1/2" Thread (Part No.33539)

Dorman – Differential Pinion Yoke Assembly (Part No.697-542)

National – Shaft Repair Sleeve (Part No.99125)

Yukon Gear – Tapered Axle Bearing And Seal Kit, 3.150" Od, For 9" Ford (Part No.10058)

Yukon Gear – Axle Bearing Retainer For Ford 9", Large Bearing, 1/2" Bolt Holes (Part No.33467)

National – Multi-Purpose Bearing (Part No.B-5020)

Yukon Gear – Dana 28, Dana 30, Model 35-Reverse, Dana 44, Dana 50 Inside Axle Snap Ring (Next To Side Gear) (Part No.33268)

Yukon Gear – Replacement Yoke For Dana 30, 44, And 50 With 26 Spline And A 1330 U/Joint Size (Part No.41019)

Yukon Gear – Outer Axle Seal For Set 20 Bearing (Part No.30030)

National – Multi-Purpose Bearing (Part No.B-2110)