1985 Chevrolet Camaro Performance Engines

Essential 1985 Chevrolet Camaro Performance Engines

Edelbrock – Pushrod Set for S/B Chevy (Part No.9630)

Pushrod Set for S/B Chevy

from

$189.99


Product Features:
  • Case-Hardened Tubing
  • Welded Ends
  • 5/16 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$94.99
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

Edelbrock – Super Victor 4500 for Raised Port 23 Degree Intake Manifold Small-Block Chevy (Part No.2971)

Super Victor 4500 for Raised Port 23 Degree Intake Manifold Small-Block Chevy

from

$494.99
Product Features:
  • 3500-8000 RPM Range
  • Single Plane Type-4500 Style Flange
  • 6.77 in. Front Height, 6.77 in. Center Height, 6.77 in. Rear Height
  • Satin Finish
  • For Raised Port 23 Degree Heads
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Cylinder Head Dowel Pins

from

$14.99
Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$52.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Advance And Retard Cam Bushings

from

$42.49
With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:
  • Advance the cam for increased torque and horsepower
  • Tune your powerband for more end torque or increase top end horsepower
  • Includes (4) offset bushings and (1) 0 degree bushing
  • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
  • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
  • Increase Top-End Horsepower
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Performer Series Retainer (Qty 16)

from

$99.99
Product Features:
  • Use W/ Valve Springs Part #5703, 5794
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Edelbrock – Front Timing Cover Gasket Set #6998 For Big-Block Chevy, With Front Seal (Part No.6998)

Front Timing Cover Gasket Set #6998 For Big-Block Chevy, With Front Seal

from

$31.99
Edelbrock part #6998 Front Timing Cover Gasket set for Big-Block Chevy. Includes front cover gasket and front seal.

Product Features:
  • Includes replacement timing cover and water pump gaskets and the crank oil seal for big block Chevrolet engines
  • Features a tough, scuff-resistant silicone rubber coating
  • Helps in sealing without the engine warming up
  • Reduces fluid migration through the gasket
  • Resists fatigue
See More

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers

from

$17.49
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:
  • Zinc plated to resist corrosion and provide a clean professional appearance
  • Made from Grade 5 steel for strength and durability
  • Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
  • Allen (socket) Head
  • Zinc Plated For Protection
See More

Competition Cams – CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA (Part No.12-250-3)

CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA

from

$258.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Mr. Gasket – Engine Sealing (Part No.6560)

Engine Sealing

from

$499.99
Manufactured from cellulose and nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement, high performance street, drag race and oval track.

Product Features:
  • Made of high temp silicone or nitrile blend rubber
  • Torque limiters to prevent over tightening
  • One piece molded rubber
  • Fits left and right hand dipsticks
See More

Mr. Gasket – Oil Pan Gasket (Part No.197)

Oil Pan Gasket

from

$30.99
Manufactured from high-density cork and rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement and high performance street.

Product Features:
  • One-piece design
  • Eliminates potential leaks
  • Prevents over tightening
  • Prevents torque loss
See More

Edelbrock – Sure Seat Valve Springs for Big-Block Chevy 396-402-427-454 V8 (Part No.5862)

Sure Seat Valve Springs for Big-Block Chevy 396-402-427-454 V8

from

$80.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

from

$65.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Edelbrock – Intake Manifold Gasket for 1958-1986 Small-Block Chevy (Part No.72018)

Intake Manifold Gasket for 1958-1986 Small-Block Chevy

from

$244.99
Any gasket can create a seal, but a good gasket can do it with reduced clamping force and for a long period of time. Edelbrock gaskets are manufactured from extremely high-quality materials and are specifically designed to fit Edelbrock intakes and cylinder heads, so there’s no chance that they will interfere with component operation.

Product Features:
  • 10-Pack of 7201 Intake Gasket Sets
See More

Mr. Gasket – Intake Gasket (Part No.143)

Intake Gasket

from

$42.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Die-cut for an excellent fit
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
See More

Weiand – Action +Plus; Water Pump (Part No.9212P)

Action +Plus; Water Pump

from

$215.99
Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:
  • Twisted Snout Water Pump Design For Updated Style
  • Street Performance
  • Heavy Duty Shaft w/5/8 in. Pilot
  • Six-Blade Stamped Steel
  • Anti-Cavitation Impeller
  • 100 Percent Leak Tested
See More

Edelbrock – Water Pump Big-Block Chevy Short/Standard in Satin Finish (Part No.8850)

Water Pump Big-Block Chevy Short/Standard in Satin Finish

from

$374.99
Product Features:
  • 5/8in. pilot shaft, aluminum, short style water pump
  • Unique O-ring provides a far superior seal than conventional gaskets
  • Extremely durable as well as efficient
  • Provides maximum flow, maximum pressure and equal distribution to both sides of the block within 1-percent
  • Includes heavy-duty roller bearing assemblies built to withstand higher torsional loads, billet steel hubs, and leak-proof seals
See More

Mr. Gasket – Ls1 Late Thermostat (Part No.6367)

Ls1 Late Thermostat

from

$31.99
Designed to open at 160 degrees every time, regardless of engine rpm, and it’s high-flow design and brass and copper construction eliminate the damaging effects of cycling when you’re stuck in stop-and-go traffic. It includes the rubber gasket and has a pressure relief valve.

Product Features:
  • Opens sooner than stock at 160 degrees
  • High flow design for performance applications
  • Includes rubber o-ring seal/gasket
  • Incorporates pressure relief valve
See More

Mr. Gasket – Tstat (Part No.6368)

Tstat

from

$31.99
Designed to open at 180 degrees every time, regardless of engine rpm, and it’s high-flow design and brass and copper construction eliminate the damaging effects of cycling when you’re stuck in stop-and-go traffic. It includes the rubber gasket and has a pressure relief valve.

Product Features:
  • Opens sooner than stock at 180 degrees
  • High flow design for performance applications
  • Includes rubber o-ring seal/gasket
  • Incorporates pressure relief valve
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1605)

Engine Valve Cover Gasket Set

from

$25.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Die cut silicone rubber gaskets conform to out-of-flat covers
  • Great for on-again/off-again situations
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Valve Cover Gasket Set (Part No.182)

Valve Cover Gasket Set

from

$42.99
Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance.brbrFits Chevrolet 396,402,427,454,502 Gen IV, Gen V and Gen VI Big Block.

Product Features:
  • This Gasket Has A Cork Rubber Blend
  • Provides Excellent Sealing And Durability
  • Extra Thick For The Hard To Seal Applications
See More

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

PERFORMANCE REAR MAIN SEAL SET

from

$36.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

Rear Main Seal Gasket

from

$23.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)

Torque Converter, Nitrous Holeshot 3600

from

$665.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:
  • 3400-3800 RPM
  • Small And Big Blocks
  • Serious Performance
  • Furnace Brazed
  • Fully Balanced
See More

B & M – Torque Converter, Holeshot 3000 (Part No.70421)

Torque Converter, Holeshot 3000

from

$789.99
The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

Edelbrock – Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8 (Part No.5002)

Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8

from

$411.99
Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:
  • Designed for 2500 to 6500 Performance
  • Designed for Hi-Perf Street; Drag or Marine Use
  • Matched to Edelbrock Torker II Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Dyno Matched/Street Proven Performance
  • Take The Guesswork Out Of Camshaft Selection
See More

1985 Chevrolet Camaro Performance Engines

Maybe you’re in the middle of a full rebuild of that 1985 Chevrolet Camaro. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 82 different Performance Engines in our inventory ranging from $14.99 to $789.99. That means you can find the exact parts or products you need to keep that 1985 Chevrolet Camaro running smoothly.

Performance Engines are only as good as their brand. We stock 7 different brands to make sure you have plenty of trusted parts to choose from for your 1985 Chevrolet Camaro. Mr. Gasket, Edelbrock, and FEL-PRO Performance are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1985 Chevrolet Camaro, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 126 reviews in this category, some of the top rated parts include Action Plus Water Pumps with 3.7 stars and Action Plus Water Pumps with 1.5 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1985 Chevrolet Camaro rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1985 Chevrolet Camaro Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1985 Chevrolet Camaro demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your Camaro the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular Competition Cams Performance Engines

We carry Competition Cams parts in our stock across Performance Engine Rocker Arms categories, plus more. For a 1985 Chevrolet Camaro, our most popular Competition Cams Performance Engines include:
MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST
from $213.99
(1)
MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST
Performance Engine Rocker Arms

Top 1985 Chevrolet Camaro Performance Engines from Mr. Gasket

Mr. Gasket products are another trusted brand when it comes to Performance Engines for your 1985 Chevrolet Camaro. Popular Mr. Gasket parts include:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats

FAQs for 1985 Chevrolet Camaro Performance Engines

What are the most purchased Performance Engines for the 1985 Chevrolet Camaro?

Out of 82 Performance Engines for the 1985 Chevrolet Camaro, the most popular in our inventory are:
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
from $195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
from $39.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $52.99
(1)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets

What are the top-rated 1985 Chevrolet Camaro Performance Engines?

Top-rated Performance Engines for your 1985 Chevrolet Camaro based on customer reviews/ratings are:
Action Plus Water Pumps
from $215.99
(3)
Action Plus Water Pumps
“I bought this item for my 1979 Camaro SBC for Street/Strip application. Water pump weighs 4 LBS less than factory, comes with its own cork gaskets. N”
Action Plus Water Pumps
from $215.99
(2)
Action Plus Water Pumps
“The twisted neck comes to far up on the hub. For a 2 groove pulley it causes the pulley to hit the water pump. You will also need new bolts for the”
Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish
from $329.99
(1)
Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish
“product fit as described , no complaints”