1984 Chevrolet Camaro Performance Engines

Includes: 2 short flat black valve covers 2 valve cover gaskets 1 flat black push-on breather 1 flat black dipstick & tube 1 flat black timing chain cover 1 flat black timing tab 1 rubber grommet for valve cover PCV hole 1 breather grommet

Product Features:

• Ideal Starter Kit
• Enhances Appearance

HYDRAULIC – Magnum: Pro Street/bracket, limited street driving. Intake, gears, 3500+ stall. Racy idle. 10.5:1 compression. OR Drag Race: 3500-4000 stall or 4 speed with 11:1+ compression.

Product Features:

• HYDRAULIC – Magnum: Pro Street/bracket, limited street driving. Intake, gears, 3500+ stall. Racy idle. 10.5:1 compression. OR Drag Race: 3500-4000 stall or 4 speed with 11:1+ compression.
• 305/305 Advertised Duration, 253/253 Duration @ .050″, .525″/.525″ Lift, 110 Lobe Separation
• Valve spring upgrade required

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Grade 8 Steel

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• New Turbine Hub
• New Springs/Rollers In Stator

Product Features:

• Dial-In Your Camshaft With Ease
• Made From Induction Hardened Billet Steel
• Solid Bushing Chain Resists Stretching
• Billet SAE-1144 Steel Crank Sprockets
• Multiple Keyways

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Product Features:

• Clean Positive Seal
• Embossed Silicone Bead Surrounding The Port
• Matched To Manifolds And Cylinder Heads

Raised 1 Piece Guide Plate Set Chevrolet Big Block With 3/8" Pushrod 7/16" Stud

Manufactured from cellulose and nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement, high performance street, drag race and oval track.

Product Features:

• Made of high temp silicone or nitrile blend rubber
• Torque limiters to prevent over tightening
• One piece molded rubber
• Fits left and right hand dipsticks

Camshaft Lock Plate w/ Bolts for GM LS GEN III/IV with 3 Bolt Camshaft

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• Has A Zinc Dichromate Finish
• Made Of High Quality Grade 8 Steel
• Has A Tall Hex Head To Prevent Wrench Slipping Off
• Extra Thick Parallel Ground Washer
• Washer Provides More Accurate And Uniform Torque

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use. These gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance. Fits Chevrolet 262,265,267,283,307,327,350,400 Gen I Small Block with Perimeter Bolt Valve Covers.

Product Features:

• Provides Excellent Flange Sealing And Durability
• For High-Performance Street, Drag Race & Oval Track Use

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

• Edge Molded Rubber Water Outlet Gasket Is Reusable
• Requires No Gasket Sealer
• Solid Aluminum Carrier For Strength/rigidity
• Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

Reduced Travel OE-Style Hydraulic Roller Lifter for ’87+ SBC, LT/LS and V6

Magnum 8.280" Long, .080" Wall, 3/8" Diameter Pushrod Set of 8

If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:

• Contains all the gaskets needed to change out your camshaft
• Fuel Injector O-Ring Not Included
• Meets Performance Standards

Roller cam lobes are ground flat rather than tapered like a flat tappet cam; it is necessary to provide some means of holding the cam back to the rear of the engine. The thrust button rides between the front of the timing gear and the back of the front cover and can be shimmed for proper end play of the cam. COMP Cams has both the solid nylon button and the roller thrust bearing available for the ultimate in performance.

Product Features:

• .810″ Length
• Ride between the front of the timing gear and the back of the timing cover
• Can be shimmed to achieve proper endplay
• Solid nylon and roller thrust bearing styles available

This 7° steel retainer for GM Gen III applications with #26915 or #26918 Beehive Valve Springs is precision machined from 4140 chromemoly steel and finished in black oxide. This precision retainer is specifically designed for positive location when combined with COMP Cams high-quality valve springs.

Product Features:

• 7° angle retainers for 1.055″ diameter valve springs, stock diameter valve stems
• O.D. – 1.030″, Step 1 – .640″
• Precision machined from 4140 chromemoly steel and finished in black oxide
• Designed for positive location when combined with COMP Cams high-quality valve springs

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

• Designed for 2500 to 6500 Performance
• Designed for Hi-Perf Street; Drag or Marine Use
• Matched to Edelbrock Torker II Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Dyno Matched/Street Proven Performance
• Take The Guesswork Out Of Camshaft Selection

Product Features:

• Replacement Gasket For PN[3789] Edelbrock Intake
• One Gasket Only
• Goes Between Base pn[3785] And Top PN[3789]
• Also Included in Base PN[3789]

Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Product Features:

• Manufactured from .020″ steel shim stock.
• Thinner than composition head gaskets – increases engine compression.
• Stress formed embossments seal extreme cylinder pressures.
• For high performance street, drag race and oval track use.

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

• Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
• 3/8 inch-16 by 1 inch bolts
• Kit includes 12 bolts and washers
• Manufactured from high quality steel
• Bolts feature hex heads

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens at 160 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully opens at Correct Temperature Consistently Regardless of engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

• Work with .530″ guides and 11/32″ valve stem diameter
• Valve stem oil seals keep unwanted oil from entering the combustion chamber
• Several different types of valve seals are offered

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.