from

$436.24

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

Short closing paths
Low volume uptake
High efficiency
Low throttling / after-suction resistance
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS
Compact design – ideal for installation in small spaces
Reduced weight – by roughly 20% compared to conventional central valve technology
Fewer components – almost half as many as compared to conventional technologies
Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
Low volume uptake – minimized elastic deformations due to smaller seals
Sealing cups supported in the housing – robustness against soiling and wear; longer life
Cr6-free surfaces for vehicles built from July 2007 (as required by law)

from

$13.69

This wheel disc hardware kit includes rubber components used to protect the caliper pins or bolts. Worn or cracked rubber components will allow excessive movement of guide pins or bolts.

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$20.78

Brake Line Junction

from

$38.82

Brake Reservoir Cap

from

$19.93

The FAE Stop Light Switch is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$28.99

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

Wearever Brake Shoes come bonded or riveted based on OE design.
Wearever Brake Shoes are coated to prevent rust.
Wearever Brake Shoes are 100% New not remanufactured.
Brand may vary by location

from

$6.79

Brakes are designed as a system and all the parts need to work together for best performance. The boot and square cut seals included in our Caliper Repair Kit, ensure that the caliper works as designed during the apply and release cycle.

Product Features:

This part matches Original Equipment (OE) quality specifications
Increases the life span of the brake pads
Restores brakes to like-new performance
Prevents noise and premature wear
Direct replacement for a proper fit

from

$20.00

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

Reduced cost
OE Quality
Complete Kit

from

$24.85

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

from

$59.96

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$9.53

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$13.98

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$99.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$16.79

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

Triggers a warning light on the dashboard
Should be replaced each time the brake pad is replaced
Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

from

$16.79

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

Triggers a warning light on the dashboard
Should be replaced each time the brake pad is replaced
Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

from

$25.49

This disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles
Ideal solution – this kit provides is a reliable replacement for original hardware that has stripped
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.49

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. Caliper Guide Pins are important to replace because they hold the brake piston in place to create effective stopping performance.

Product Features:

This part matches Original Equipment (OE) quality specifications
Easy and fast replacement
Helps deliver a quieter, more efficient braking system
Corrosion resistant coating for long-lasting durability against harsh roads
Manufactured with quality materials to suppress high stress levels

from

$31.99

The Power Stop Z16 Evolution ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z16 pads maintain consistent wear and performance while ensuring a fast break-in. The Z16 Evolution ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise-free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking

from

$37.99

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking
Includes Premium hardware for easy installation

from

$22.99

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

Dependable stopping power
Single layer shim for quiet braking
OE-designed slots and chamfers to reduce noise and vibration
Powder-coated backing plate prevents corrosion

from

$15.97

The Vaico Booster Non Return Check Valve is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$43.33

Booster Check Valve

from

$25.49

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Tensile minimum load holds up to 1800 N
All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
Brand may vary by location

from

$20.99

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Tensile minimum load holds up to 1800 N
All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
Brand may vary by location