1983 Ford F-250 Pickup Differentials

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

Pinion seal for 10.25″ Ford.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Ford 10.25″

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Product Features:

• DANA-60 R/P 3.54 STD MG 24813-5X (USES PRE-LOAD SHIMS)

Set-up carrier bearing kit (2 bearings, no races) for Dana 60 and 70. 387A. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 60
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

• Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

Yukon standard open spider gear kit for Dana 50 IFS with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 50 open differential with 30 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
• For Trac Loc positraction applications only

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• Crush sleeve spacer for Ford 9.75″
• 0.280″ tall

Product Features:

• MINI INSTALL KIT FORD 8.8

RngPnn

Yukon replacement axle for Dana 44-IFS Ford F250, Right hand, 23.65″ inner, 81-91, 30 spline. Yukon front axles come with a one year warranty against manufacturing defects.

Product Features:

• 30 spline
• 23.65″ long
• Fits Dana Spicer 44 IFS in 1981-1991 Ford F250
• Right hand inner
• 5-760X U-joint size

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 60 front
• Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

Differential

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Yukon replacement positraction internals for Dana 60 and 70 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Clutch kit
• Fit Dana Spicer 60 Powr Lok positraction with 35 spline axles
• Smooth design
• Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

• OUTER SHAFT 9.72 O.A. ’71-77 BRONCO W/ DISK BRAKES ’78-79 BRONCO & F150

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

Replacement ring gear bolt for Model 20, Grand Cherokee 35, “Super” Dana 30 & Dana 50. 7/16″ x 20.

Product Features:

• Ring gear bolt for AMC Model 20, “Super” 35, Dana Spicer “Super” 30 and Dana Spicer 50
• 7/16″ 20 thread

Replacement side gear thrust washer for Spicer 50 .

Product Features:

• Side gear thrust washer
• Fits Dana Spicer 50

Product Features:

• Each LuK GearBOX contains all the OE quality bearings needed for a professional transmission repair
• LuK Differential Bearing Kits are designed to meet or exceed OEM requirements. This will ensure customer satisfaction.
• LuK Differential Bearing Kits contain the bearings and seals needed to complete the job.
• LuK Differential Bearing Kits include wear parts such as seals, O-rings, shaft sealing rings, support bearings and spare parts where necessary for eliminating the specific cause of failure.

Product Features:

• Cross pin shaft for Dana Spicer 44
• Fits standard open differentials only

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM89410 race
• All steel construction

Product Features:

• Clutch kit
• Fit Dana Spicer 44 and Chrysler 8.75″ Powr Lok positraction
• Smooth design