1982 Mercury Grand Marquis Car Parts & Accessories

Part was perfect fit.

Bottom Line

Great

Bottom Line

This is the best sealing, most forgiving, conventional graphite head gasket available. Don't hesitate to use it on your boosted/n2o cars. The only drawback is that they are very messy to clean off of the head/deck surfaces when you do need to change them.

Bottom Line recommended

Gasket is very easy to work with...goes on dry and the installation studs help to keep the gasket and pan aligned while you put your bolts in. Very pleased.

Bottom Line

eazest oil pan gasket ive ever installed hope it don't bite me if i ever have to put another timing chain in it

Bottom Line

A good quality gasket set. Would recommend others consider purchasing.

Bottom Line

Has held up the first few months. Fit correctly.

Bottom Line

Good fit

Bottom Line

Great product for the price and engineering. Felpro is a great company and one of my favorite Gasket companies to buy from . The craftsmanship of the Felpro brand is one of a kind. Never had one break or shrink on any of my rebuilding. The Gaskets are better than the original manufacturers Gasket on the engine when purchased new from the factory. I've ran Felpro Gasket sets for years on high performance engines with out any trouble or worrying that they may or may not leak. I highly recommend Felpro!

Bottom Line recommended

Great

Bottom Line

They are metal, for an additional couple dollars.

Bottom Line

perfect

Bottom Line

This is a sweetly made product with that hotrod look and feel.This shifter was easy to install and a knock out to drive.No down falls as far as I'm aware of after 9 days of use..so far.

Bottom Line recommended

Saved us running around, part was in stock as needed and priced right.

Bottom Line

spicer quality. usa made.

Bottom Line

Fixed my problem, spicer.

Bottom Line

Good so far

Bottom Line

Part fit great- -but what a pain to get the old one off- -

Bottom Line

This part isn't hard to diagnose. You can simply slide under the vehicle and tug on the steering linkage, or use a prybar. If the part is original the wear by now will be very obvious. The linkage should be tight with little movement. If this part is bad, any disturbance (braking, bumps, etc) will make the linkage move (change geometry) and thus change wheel toe, causing one one wheel to point slightly in another direction. Idler arm is the pivot point on the right side. If this part is bad you may experience pulling or vibration while braking, poor handling when you hit a bump and tracking to a side when driving. I almost thought I had a warped rotor! I installed this without lifting the vehicle in a bit over an hour, but I had air tools. Was a 98 Grand Marquis. Took a bit of time to get the corroded cotter pin out in that tight position. There was some corrosion, used lots of penetrant and the frame bolts didn't spin out of their splines. Also, you have to twist the part just right so it aligns with the frame when you install. Thread cutting Grease fittings are best installed with an 8mm gearwrench with your finger holding the top down. This is a Quality product that will likely last the life of the vehicle. These fit many RWD Ford vehicles from the late 70s to around 2002. The insert had a 1989 date so it is a time tested design, and major improvement over the original (which has serviceable bushings meant to wear). Be sure to lube this part every 3-4K miles. If you do that it will probably last forever. Make sure you either DIY or remind the lube place to grease the joints. Some places don't, or you have to pay a bit more.

Bottom Line recommended

Ended up returning, as this same kit came with the universal Imperial power steering cooler for an 05 Chevrolet Silverado. So I did use the kit, just came with the new cooler. Worked great and made for simple mounting. Basically just a few zip tie type things that go through the condenser and p/s cooler fins..zips in and holds firm! Good thing as one of the Original p/s cooler mounting bolts were rusted and snapped. Beats drilling and tapping.

Bottom Line

Ended up not using, wasn't the kit's fault. Mounted cooler with bolts instead of the pull through plastic ties in this kit.

Bottom Line

The power steering cooler I bought came with a couple of these (three, I think) but I'm glad I spent the few bucks extra for these. I encountered a minor snafu positioning the cooler unit. These allowed me to just snip off the ones that came with the unit and just pop in a few new ones. So easy, even I managed, with my wife standing by giving me step by step directions without which I couln't have finished (note; she made me say that. Tain't really the way it was. but, hey.........)

Bottom Line

After I replaced tie rod car drives much better, good parts

Bottom Line

The application was for a 1996 Lincoln Town Car. Made in the USA and Quality is apparent. Hope this is not going to be moved to China.

Bottom Line

Got rid of my steering slop.

Bottom Line recommended

good antifreeze

Bottom Line

Great price

Bottom Line

Good fit, no leaks

Bottom Line

Good price

Bottom Line

Good product

Bottom Line

Use this in place of the expensive BMW fluid

Bottom Line

Order was sent to the wrong store

Bottom Line

A bit Pricey

Bottom Line

Let Advance Auto have the type of antifreeze I needed it's worked well thank you

Bottom Line