1982 Dodge W350 Drive Shafts and Axles

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

• Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
• 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
• Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
• Serviceable construction – non-staked universal joints are designed for future serviceability

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100 percent dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

• Built to match O.E. form, fit and function.
• 100 percent NEW universal joints are installed to ensure proper fit and optimal performance.
• All slip yokes are lubricated to prevent premature wear.
• Units are 100 percent dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

Yukon billet replacement yoke for Dana 60 and 70 with 29 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 60 and 70
• 29 spline
• 1350 u-joint size
• Outside snap ring design
• 3.625″ snap ring span
• 1.188″ cap diameter
• U-bolt style

Product Features:

• Pinion yoke dust shield
• Fits Dana Spicer 60 and 70

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

• OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
• Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
• The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
• Zerk allows for lubricating at regular intervals to help extend the life of the part.

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.

Product Features:

• Rear axle seal
• 2.530″ O.D.

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Yukon replacement axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit for ’75 to ’93 Dana 60 and Dodge 3/4 ton truck front axle. This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.

Product Features:

• Fits 1975-1993 Dodge 3/4 ton
• Includes axle bearings, races and seal
• Services one side

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1561TV axle bearing and seal kit, for Ford and Dodge, TorringtonBrand, 2.985″ OD, 1.700″ ID. This axle bearing & seal kit services one side only.

Product Features:

• Fits Ford and Dodge applications
• Includes axle bearing and seal
• Torrington Brand
• Services one side
• 2.985″ O.D.
• 1.700″ I.D.

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Yukon replacement 1541H outer stub axle shaft for Dana 60 with a length of 12 inches and with 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H front axles come with a one year warranty against manufacturing defects.

Product Features:

• 30 spline
• 12″ long
• Fits Dana Spicer 60 in 1977-1991 GM 1 ton and 1976-1993 Dodge 1 ton
• Outer stub
• 5-332X U-joint size

Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

• Fits Dana Spicer 60 front in GM and Dodge trucks
• 4340 Chromoly
• Outer stub
• 30 spline
• 12″ from end of splines to center of u-joint bore

Center Support

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 92-05; DODGE 84-10; GMC 92-05; RAM 11-20;. Please verify your application.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1984-2020
• Weight approx: 4 Lbs
• BEARING ID / BORE: 1.3780 INCH / 35 MM
• CENTERLINE: 2.28 INCH / 58 MM
• MOUNT WIDTH: 6.62 INCH / 168 MM
• STYLE: SQUARE FRAME

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1955-2018
• Weight approx: 3 Lbs
• BEARING ID / BORE: 1.3780 INCH / 35 MM
• CENTERLINE: 2.28 INCH / 58 MM
• MOUNT WIDTH: 6.62 INCH / 168 MM
• STYLE: ROUND FRAME
• COMPLETE MOUNT

Product Features:

• Drive flange cap
• Fits Dana 60
• Yukon engraved

Dana 60 semi-float C-clip.

Product Features:

• C-clip
• Fits Dana Spicer 60

9.25″ Chrysler C/clip, 0.205″ wide for 4137429 axle.

Product Features:

• c-clip for Chrysler 9.25″ rear
• 0.205″ thick

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

• BUILT TO LAST – Advanced heat treatment process for strength
• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

• BUILT TO LAST – Advanced heat treatment process for strength
• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on