from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$31.99

Product Features:

Brand may vary by location

from

$17.99

9.25″ Chrysler C/clip, 0.205″ wide for 4137429 axle.

Product Features:

c-clip for Chrysler 9.25″ rear
0.205″ thick

from

$14.99

Dana 60 semi-float C-clip.

Product Features:

C-clip
Fits Dana Spicer 60

from

$15.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$24.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$18.99

Replacement Inner axle seal for Dana 60 front.Yukon Mighty seal.

Product Features:

Front inner axle seal
Fits Dana Spicer 60 front

from

$7.99

Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.

Product Features:

Rear axle seal
2.530″ O.D.

from

$129.99

Product Features:

Drive flange cap
Fits Dana 60

from

$44.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$36.49

CENTER SUPPORT

from

$233.99

Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
Strap style

from

$278.99

Yukon replacement yoke for Dana 60 and 70 with a 1410 U/joint size. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1410 u-joint size
4.188″ snap ring span
1.188″ cap diameter
Outside snap ring design
Strap style

from

$3.29

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

from

$5.29

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$179.99

Yukon replacement axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit for ’75 to ’93 Dana 60 and Dodge 3/4 ton truck front axle. This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.

Product Features:

Fits 1975-1993 Dodge 3/4 ton
Includes axle bearings, races and seal
Services one side

from

$92.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1561TV axle bearing and seal kit, for Ford and Dodge, TorringtonBrand, 2.985″ OD, 1.700″ ID. This axle bearing & seal kit services one side only.

Product Features:

Fits Ford and Dodge applications
Includes axle bearing and seal
Torrington Brand
Services one side
2.985″ O.D.
1.700″ I.D.

from

$78.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 92-05; DODGE 84-10; GMC 92-05; RAM 11-20;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1984-2020
Weight approx: 4 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: SQUARE FRAME

from

$197.95

Rugged SKF drive shaft support bearings are built to meet or exceed OE specifications. They are also built on the years of experience that SKF has earned designing and supplying bearings to the world’s largest OE manufacturers. Engineered and manufactured to specific application requirements that deliver precise drive shaft alignment and support. Center support bearings are pre-lubricated and sealed with metal reinforced seals to prevent contamination. Rubber support cushions are manufactured from durable rubber compounds that provide maximum support while isolating the driveline shaft from damaging vibration. Drive shaft support frames are constructed from high quality steel or aluminum that provides additional strength and long life in harsh environments.

Product Features:

OE Quality, fit and performance
Precise driveshaft alignment and support
Pre-lubricated and sealed
Metal reinforced seals to prevent contamination
Manufactured from durable rubber compounds

from

$511.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$377.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$1151.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$167.99

Product Features:

Fits Dana Spicer 60 front in GM and Dodge trucks
4340 Chromoly
Outer stub
30 spline
12″ from end of splines to center of u-joint bore

from

$255.99

Yukon replacement 1541H outer stub axle shaft for Dana 60 with a length of 12 inches and with 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H front axles come with a one year warranty against manufacturing defects.

Product Features:

30 spline
12″ long
Fits Dana Spicer 60 in 1977-1991 GM 1 ton and 1976-1993 Dodge 1 ton
Outer stub
5-332X U-joint size

from

$229.99

Product Features:

35 spline
12.0″ long
Fits Dana Spicer 60 in GM and Dodge
Outer stub
5-332x U-joint

from

$81.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.

from

$40.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.