1980 Oldsmobile Custom Cruiser Performance Engines

“Edelbrock part No: 3702 Performer-Plus camshaft is designed for small-block Chevy 305-350 T.B.I & LG-4 V-8 applications. This Edelbrock cam kit produced 245 ft-lbs. of torque when used with No: 3701 intake and stock iron cylinder heads on a 350 engine. The camshaft will produce optimum torque from the low-end to the mid-range, Performer-Plus camshafts match with Performer manifolds for vehicles operating from off-idle to 5500 rpm. This Performer-Plus is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. All camshafts include flat tappet lifters, assembly lube and instructions. Camshaft Specifications: – Duration at .050 Intake: 194 degrees – Duration at .050 Exhaust: 214 degrees – Lift at Valve Intake: .398″” – Lift at Valve Exhaust: .442″” – Lobe Separation: 112 Degrees – Intake Centerline: 107 Degrees – Idle Vacuum at 1000 RPM’s: 16″””

“Edelbrock part No: 3712 Performer-Plus camshaft is designed for small-block Oldsmobile 350-403 V-8 applications. This Edelbrock cam kit produced 330 ft-lbs. of torque when used with No: 3711 intake and stock iron cylinder heads on a 350 engine. The camshaft will produce optimum torque from the low-end to the mid-range, Performer-Plus camshafts match with Performer manifolds for vehicles operating from off-idle to 5500 rpm. This Performer-Plus is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. All camshafts include flat tappet lifters, assembly lube and instructions. Camshaft Specifications: – Duration at .050 Intake: 204 degrees – Duration at .050 Exhaust: 214 degrees – Lift at Valve Intake: .449″” – Lift at Valve Exhaust: .473″” – Lobe Separation: 114 Degrees – Intake Centerline: 106 Degrees – Idle Vacuum at 1000 RPM’s: 16″””

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

The COMP Cams 08-411-8 Xtreme Energy Hydraulic Roller Camshaft is marketed as a street/strip performance camshaft for small block Chevy engines, delivering aggressive mid-range horsepower, crisp throttle response, and reliable drivability.

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

SMALL BLOCK CHEVY HYDRAULIC COMPLETE KIT – High performance. Biggest cam with stock converter but better with 2000+ stall. Use lower gears. Mild rough idle.

“Edelbrock Performer-Plus Camshaft No: 2103 is designed for 400 Chevy V8 engines and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2103 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 395 Ft Lbs of Torque when paired with Performer Intake manifold No: 2101 and stock cylinder heads. 50-State Legal E.O. No: D-215-19 for 1957-86 small-block Chevrolet. Camshaft specifications: – Intake duration: 214 Degrees – Exhaust duration: 214 Degrees – Intake lift: .442″” – Exhaust lift: .442″” – Lobe separation: 112 Degree – Intake Center Line: 107 Degree – Vacuum: 15″””

“Edelbrock Performer-Plus Camshaft No: 2102 is designed for 265-400 Chevy V8 engines from 1957-86 and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2102 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 320HP and 382 Ft Lbs of Torque when paired with Performer EPS intake manifold No: 2701 and Performer cylinder heads No: 60909. 50-State Legal E.O. No: D-215-19 for 1957-86 small-block Chevrolet. Camshaft specifications: – Intake duration: 204 Degrees – Exhaust duration: 214 Degrees – Intake lift: .420″” – Exhaust lift: .442″” – Lobe separation: 112 Degree – Intake Center Line: 107 Degree – Vacuum: 14″””

This Holeshot 3000 fits 1965-91 GM TH400, 425, 375 and 1968-81 TH350, 375B (not 350C). Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 3000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Has both 10.75 and 11.50-inch bolt circles.

The Tork Master 2400 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1996 4L60E w/30 spline input transmissions. This converter retains the lock-up feature. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75 in. bolt circle

This Holeshot 2000 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1997 4L60E w/30 spline input, and 1997-04 Corvettes. This converter retains the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace-brazed impeller fins and turbine, a new precision alloy impeller hub, and new heavy-duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate-type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, and less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide, or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

Edelbrock Performer Small-Block Chevy Intake Manifold for Street Performance, 3701.

Edelbrock RPM Air-Gap Oldsmobile 455 Intake Manifold, 7551.

“Edelbrock part #2999 Victor Jr. 23 degree Tall intake manifold provides maximum performance for engines with standard port location, iron and aluminum cylinder heads. This versatile manifold is excellent for many applications from high-performance’s street to drag/circle track racing. This Victor Jr. 23 degree tall intake manifold features a 1″” taller carb pad than the Victor Jr. #2975.”

Weiand Team G Intake Manifold, 7531.

“Competition Cams Magnum 7.200″” Long, .080″” Wall, 5/16″” Diameter Pushrod Set, 7608-16. ”

“Edelbrock part No: 9630 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise formed wedged ends for a high quality fit with the cup seats. A black oxide finish is added for corrosion resistance. Pushrod Specifications: – Outside Diameter: 5/16″” – Length: 7.8″” – Stock length”

“Competition Cams Magnum 8.280″” Long, .080″” Wall, 3/8″” Diameter Pushrod Set of 8, 7131-8. ”

“Magnum Pushrods from COMP Cams offer an affordable solution for your .080″” wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.”

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.