from

$8.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$48.99

7.25″ Ford & 6.75″ Ford pinion seal.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Ford 6.75″ and 7.25″

from

$4.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$42.99

9.25 Chrysler FRONT PINION KIT , 03 & UP DODGE TRUCK .

Product Features:

Pilot bearing
Fits Ford 8″

from

$68.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Ford 8″
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$3.99

Trac Loc ring gear bolt washer for 8″ and 9″ Ford.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For Trac Loc positraction applications only

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$5.99

Product Features:

Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
0.030″ thick

from

$8.99

Product Features:

Trac Loc spring for Ford 8″ and 9″

from

$22.99

9″ FORD SPARTAN LOCKER EXTRA SHORT Cross Pin SHAFT .

Product Features:

USA Standard Gear heavy-duty cross pin shaft
Fits Ford 9″

from

$234.99

Good used Yukon yoke for Ford 8″ with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8″
25 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
U-bolt style

from

$535.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits Ford 8″
8.00″ ring gear diameter
25 spline pinion
10 ring gear bolts
4.11 ratio

from

$23.99

Pinion gear for 8″ and 9″ Ford.

Product Features:

Pinion gear
Fits Ford 8″ and 9″

from

$11.99

8″ dropout housing gasket.

Product Features:

Dropout gasket
Fits Ford 8″

from

$229.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 8″
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$22.99

Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:

Steel-backed Babbitt lining material
Used in automotive and high-performance
Babbitt is designed to perform under extreme loads w/o damaging other engine parts
Babbitt is more environmentally friendly than other material
ISO & QS certified manufacturing

from

$9.99

8″ Ford O-ring.

Product Features:

Pinion support o-ring
Fits Ford 8″

from

$10.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$7.99

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

Pinion nut for Ford 7.5″, 8″ and 9″
3/4″ x 20 thread
1 1/6″ socket

from

$31.99

8″ Ford pinion shim kit.

Product Features:

Pinion depth shims for Ford 8″

from

$44.49

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!