from

$149.99

Kits include most popular chrome dress-up components, including short, OEM height valve covers with integral oil baffles.

Product Features:

Includes oil baffles
Chrome plated

from

$368.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$76.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$25.99

Thick, molded rubber with steel carrier. Manufactured from high-density cork and rubber blend gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage. Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Available in standard or extra thick to provide additional valve train to cover clearance. For OE replacement, high performance street, drag race and oval track.

Product Features:

Made from cork/rubber compound
Can be reused many times
Thick; fuel-resistant

from

$190.99

Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:

7.7 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$297.99

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$185.99

Product Features:

Dial-In Your Camshaft With Ease
Made From Induction Hardened Billet Steel
Solid Bushing Chain Resists Stretching
Billet SAE-1144 Steel Crank Sprockets
Multiple Keyways

from

$27.99

Product Features:

1.98″x2.26″
Features Embossed Silicone Bead Around The Intake Ports & Water Openings
.060″ Thick
Multi Piece Configuration
End Seals Not Included

from

$40.99

Super Intake Manifold Bolts

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$58.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$54.99

Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:

Fits Ford 429 – 460 engines
Has a 3/8 inch NPT threaded hole for temperature sensor
Includes sealing O-ring
Chrome plated
Easy to install
Hardware not included

from

$35.99

The grade 8 bolts feature high hex head to prevent socket slippage. The thick parallel ground washer allows accurate uniform torque. Black finished, complete with split lock washer to prevent loosening.

Product Features:

Grade 8 material
Heat-treated for strength
Hex prevents socket slippage
Accurate and uniform torque
Black plated finish

from

$550.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$659.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Torque Improved Over Stock
Accept V8 Pedestal Rocker Arms
Accept V8 Valvetrains

from

$726.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Torque Improved Over Stock
Accept V8 Pedestal Rocker Arms
Accept V8 Valvetrains

from

$597.99

Edelbrock part #21813 Performer 351W intake manifold is designed for street 351 c.i.d. Ford Windsor V8’s. Will not fit Boss 351. Aftermarket 4-bbl carbs are not compatible with Ford Auto Overdrive Transmission (AOD) unless used with Lokar bracket SRK-4000

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
3.4 in. Front Height, 4.07 in. Center Height, 4.75 in. Rear Height
Black Powder Coated Finish
Made In The USA

from

$518.99

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM street-driven power. Dual-plane high-rise intake. Race winning technology.

Product Features:

Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed for 1500 to 6500 RPM Street-Driven Power
Dual-Plane High-Rise Intake
Race Winning Technology

from

$77.99

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

Sure-lock rocker arm nuts
Precise valve train adjustment
Keep rocker arms locked
High-quality grade steel
Heat-treated for ex strength
Plated with durable gold tone finish

from

$237.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$107.99

Product Features:

Highest Quality Head Bolts
Cold-Formed/Heat Treated
Ensures Molecular Integrity
Reduced Diameter Bolt Heads
Hardened/Parallel-Ground Washers Included
Rated At 170000 psi
Manufactured By ARP

from

$358.99

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.70 in. Block To Hub Height
Black Finish

from

$300.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Fits Later Applications w/Water Inlet On LH Side
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested
Bearing Shaft And Seal

from

$526.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features: