1979 Jeep Wagoneer Drivetrains

Below you will find various in-demand Jeep Drivetrains, components and accessories for your 1979 Wagoneer. Advance Auto Parts has popular Wagoneer parts like Differentials, Universal Joints, Transfer Cases and more. You’ll also find aftermarket and OEM Drivetrains for other Wagoneer model years including 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990 and more. Select a category of 1979 Jeep Wagoneer Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1979 Jeep Wagoneer Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

U-Joints

4WD Hubs

Miscellaneous CV and U-Joint Parts

Differential Open Unit and Components

Differential Covers

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Axle Shafts

Spindle Hub Seals

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Locking Hub Service Kits

Axle Spindle Seals

U-Joint Centering Yokes

Differential Cover Bolts

Input Shaft Pilot Bearings

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Axle Spindle Bearings

Transfer Case Overhaul Kits

Differential Clutch Packs

Rear Axle Shaft Bearings

Differential Mini Spools

Differential Ring and Pinions

Stub Axles

U-Joint U-Bolt Kits

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Differential Air System Seal Housings

Differential Spools

Differential Carrier Bearings

Transfer Case Switches

Front Differential Cover Gaskets

Rear Housing Cover Gaskets

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Transfer Case Differential Bearings

Drive Shaft Seals

Differential Seals

Complete Differentials

Bearing and Seal Overhaul Kits

Differential Drain Plugs

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Pinion Shafts

Differential Carrier Bearing Shims

Axle U-Bolt Kits

Input Shaft Seals

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Mounting Adapter Seals

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Axle Shaft Studs

Differential Drive Pinion Oil Deflectors

Transfer Case Stabilizer Bushings

Differential Carrier Bolts

Axle Shaft Snap Rings

Spindle Washers

Axle Shaft Bearing Retainers

Differential Ring and Pinion Kits

Limited Slip Differential Assemblies

Differential Pinion Bearing Spacers

Universal Joint Strap Bolts

Differential Clutch Pack Clips

Differential Lock Washers

Axle Housing Shims

Differential Lock Thrust Blocks

Axle Pinion Repair Sleeves

Axle Shaft Bearing Spacers

Universal Joint Snap Rings

Universal Joint Straps

Drive Shaft Flanges

Transfer Case Shift Rail Spring

Essential Drivetrains for 1979 Jeep Wagoneers

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$8.99

Model 20 0.005″ axle end play shim.

Product Features:

Axle end play shim for AMC Model 20
0.005″ thick

from

$182.99

Replacement redi-sleeve yoke saver for Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 .Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits Dana Spicer 25, 27, 30, 4 and 50

from

$1.99

Crown Automotive offers the largest line of replacement parts for Jeep (R), as well as a growing line of parts for Chrysler and Dodge vehicles. Our applications features Axle, Body, Brake, Clutch, Cooling, Electrical, Engine, Fuel, Lamps, Mirrors, Steering, Suspension, Transmission and Wiper.

Product Features:

Shift Rod Poppet Springs Keep The Shift Rail In Place
Jeep Manual Transmission Synchronizer Springs Are Quality Components From A Trusted Name In Jeep Replacement Parts
Designed And Built To OEM Specs
Easy To Install

from

$22.79

Product Features:

FORD 9″ SOLID SPACER KIT

from

$104.99

Product Features:

Carrier shims for Dana Spicer 60 and 70U

from

$24.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$9.99

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$233.99

Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
Strap style

from

$101.99

Product Features:

MINI SPOOL – DANA 44, 30 SPL.

from

$43.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$276.99

Set-up carrier bearing kit (2 bearings, no races) for Dana 60 and 70. 387A. No return.

Product Features:

Set up bearing kit
Fits Dana Spicer 60
Easily slips on and off carrier journals to allow for easier carrier shim adjustment

from

$414.99

Yukon Performance steel spool for Dana 60 with 35 spline axles. fits 4.10 and down. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler Dana Spicer 60 with 35 spline axles
4.10 and down ratio only
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$5.99

Product Features:

Rear axle stud for Dana Spicer 44 and AMC Model 35
1/2″ x 20 thread
0.618″ knurl diameter
1 15/32″ long
31/64″ shoulder length

from

$19.99

Product Features:

Axle bearing retainer for Jeep TJ rear with Dana Spicer 44
3/8″ bolt holes
1 5/8öx3 3/16ö bolt pattern

from

$23.99

This transfer case switch directly replaces the original equipment switch on certain vehicle years, makes and models.

Product Features:

Direct replacement – this 4WD switch matches the fit and function of the original switch on specific vehicle applications
Effective fix – restores proper 4WD operation after original switch degrades and fails
Durable construction – built for reliable longevity, free of defects in materials and craftmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$327.99

Yukon standard open spider gear replacement kit for Dana 25 and 27 with 10 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Dana Spicer 27 open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$1145.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

Fits Dana Spicer 60 with 40 spline axles
4.10 and down ratio only
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$23.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 353, 354, 361, 369 & 497
Fits 1-1/16″ bearings

from

$21.29

Product Features:

PINION SHIMS – AMC MODEL 20

from

$11.49

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$559.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits standard rotation Dana Spicer 60
9.75″ ring gear diameter
29 spline pinion
12 ring gear bolts
5.86 ratio

from

$125.99

Yukon replacement axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit for ’77 to ’91 Dana 44 and Jeep Wagoneer front axle. This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.

Product Features:

Fits 1977-1991 Jeep Wagoneer
Includes axle bearings, races and seal
Services one side

from

$21.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$179.99

Yukon 1541H replacement outer stub axle shaft for Dana 44, ’71-’79 Ford Bronco with a length of 9.72 inches and with 19 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy front axles come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44 in Ford F150 and Bronco and Jeep Wagoneer with drum brakes
Outer stub
19 spline
9.72″ from end of splines to center of u-joint bore

from

$6.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

Upgrade your 1979 Jeep Wagoneer with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1979 Jeep Wagoneer, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Jeep or enhancing its overall performance, Drivetrains are key to keeping your Wagoneer functioning at its best. At Advance Auto Parts, we offer a wide selection of 369 Drivetrains for the 1979 Jeep Wagoneer, designed to meet your needs without breaking the bank. From Differential replacements to Universal Joints upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1979 Jeep Wagoneer at great prices. Our Drivetrains inventory for this model ranges from just $1.99 to $1,566.99, with an average price of $179.36. Our 369 Drivetrains in stock come from 20 trusted brands, so you’re sure to find the right part for your 1979 Jeep Wagoneer without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1979 Jeep Wagoneer, we stock popular OEM and aftermarket Drivetrains from top names like Spicer, Moog, Driveworks, and more. Spicer Drivetrains start at just $31.99 and boast an impressive 4.6 stars average rating from customers. Moog and Driveworks also bring quality to the table, with Drivetrains available starting at $6.99, and at an average 4.5 stars rating. With 856 customer reviews and counting, our 1979 Jeep Wagoneer Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1979 Jeep Wagoneer is always ready to roll. We’re committed to providing you with everything you need to keep your Wagoneer in top shape, all in one place. Start shopping confidently below for your 1979 Jeep Wagoneer!

Best-Selling Differentials for 1979 Jeep Wagoneers

Enhance the driving experience in your Jeep with 241 quality Differential components, starting at $1.99.

show more show less

from

$35.99

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life. Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$10.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$43.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$7.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$23.49

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$6.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$505.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!

from

$151.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

DANA-30 JEEP MASTER KIT 66-90

from

$168.99

DANA-44 LATE TIMKEN MASTER KIT

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$11.99

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
3/8″ x 24 thread

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$3.99

Replacement ring gear bolt for Model 20, Grand Cherokee 35, “Super” Dana 30 & Dana 50. 7/16″ x 20.

Product Features:

Ring gear bolt for AMC Model 20, “Super” 35, Dana Spicer “Super” 30 and Dana Spicer 50
7/16″ 20 thread

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$7.99

7/16″ TO 3/8″ ring gear bolt spacer sleeve.

Product Features:

Ring gear bolt sleeve
Adapts 7/16″ to 3/8″

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$9.99

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
0.480″ tall

from

$15.99

Product Features:

Carrier shim kit for Dana Spicer 30 with 30 spline axles

from

$1.99

Product Features:

BOLT 9″ FORD OPEN R.G. SAME AS M-4216A200

from

$6.99

Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
3/4″ x 16 thread

from

$17.99

Replacement pinion seal for Dana 25, Dana 27, Dana 30, D36, Dana 44, & Dana 50 .Yukon Mighty seal.

Product Features:

Pinion seal
Fits Dana Spicer 25, 27, 30, 40 and 50

from

$12.99

Product Features:

KIT SHIM

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

Most Popular 1979 Jeep Wagoneer Universal Joints

Customize your Jeep with 52 Universal Joints products like U-Joints, U-Joint Strap Kits, and U-Joint U-Bolt Kits, all priced under $609.99.

show more show less

from

$31.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$23.99

For U-Joints 353, 354, 361, 369 & 497
Fits 1-1/16″ bearings

from

$15.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$36.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$26.99

For U-Joints 315G, 317, 319 & 457
Contains two 1-1/2″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

from

$35.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$40.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$55.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$33.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.49

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$29.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$24.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$167.99

Machined bodies to meet the tight tolerances
Forged and cast material to meet the performance requirement
Minimize the flash lines for less interference
Cleaning process induces compressive strength for increased performance
Machined and threaded holes for mounting ease
Rust preventative added for longer shelf life

from

$35.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE: Available for foreign and domestic nameplates
GREASABLE DESIGN: Greaseable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT: Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE: Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$7.49

This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$38.99

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$73.99

Fits standard rotation Dana Spicer 44 TJ Rubicon
8.50″ ring gear diameter
26 spline pinion
10 ring gear bolts
5.13 ratio

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$45.99

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

Top Picks for 1979 Jeep Wagoneer Transfer Cases

Upgrade Jeep Wagoneers with top-quality Transfer Cases parts, including 22 OEM and aftermarket selections for your 1979 model.

show more show less

from

$17.99

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$12.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$6.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$8.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$7.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$20.49

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$4.99

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 deg. F to 225 deg. F / -40 deg. C to 107 deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$13.49

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$18.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$24.99

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$3.99

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$44.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.79

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$171.99

TCaseBrg-SealKit

from

$22.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$15.99

Crown Automotive Transfer Case Switches Are Ideal Replacements To Keep Your Rig Rollin
Weatherproof-Sealed To Guard Against Failure
Offers OE Fit And Function
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts

from

$11.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$8.99

Provides Leak Free Operation
Hazardous Free Material
Offers OE Fit And Function
Long-Lasting, Durable Crown Automotive Products

from

$8.99

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$8.89

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$1.99

Shift Rod Poppet Springs Keep The Shift Rail In Place
Jeep Manual Transmission Synchronizer Springs Are Quality Components From A Trusted Name In Jeep Replacement Parts
Designed And Built To OEM Specs
Easy To Install

In-Demand Drive Shafts and Axles for 1979 Jeep Wagoneers

Select from 37 premium Drive Shafts and Axles parts for your 1979 Jeep Wagoneer, with prices ranging from $4.99 to $1,016.99.

show more show less

from

$55.99

from

$38.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$14.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$7.99

Wheel Lug Stud

from

$9.99

Model 20 inner axle seal.Yukon Mighty seal.

Product Features:

Rear inner axle seal
Fits AMC Model 20

from

$17.79

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$10.99

Model 20 outer axle seal for tapered axles.Yukon Mighty seal.

Product Features:

Rear outer axle seal
Fits AMC Model 20

from

$9.99

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Easy Installation

from

$30.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$19.99

Outer axle seal to be used with set10 bearing.Yukon Mighty seal.

Product Features:

Rear axle seal
Axle bearing and seal kit for Dana 44 rear and Nissan Titan rear
For use with Set10 bearing

from

$123.99

Yukon replacement axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit (Set10), some flanged, Timken brand, for Dana 44 and Model 20. This axle bearing & seal kit services one side only.

Product Features:

Axle bearing and seal kit for Dana 44 rear and Nissan Titan rear
Includes axle bearing and seal
Services one side

from

$21.49

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:

2.75 in.
OE Style
Direct Fit

from

$19.99

Product Features:

Axle bearing retainer for Jeep TJ rear with Dana Spicer 44
3/8″ bolt holes
1 5/8öx3 3/16ö bolt pattern

from

$4.99

Dana 28, Dana 30, Model 35-Reverse, Dana 44, Dana 50 INside axle snap ring (next to side gear).

Product Features:

Inner axle snap ring for Dana Spicer 28, 30, 44 and 50
Intalls next to side gear

from

$179.99

Fits Dana Spicer 44 in Ford F150 and Bronco and Jeep Wagoneer with drum brakes
Outer stub
19 spline
9.72″ from end of splines to center of u-joint bore

from

$121.99

Yukon replacement yoke for Dana 30, 44, 50, and Dana 300 with 26 spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$148.99

Yukon 1541H replacement outer stub axle shaft for Dana 44 and 8.5″ GM with a length of 9.94 inches and with 19 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H front axles come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44 in GM truck and Blazer and Jeep Wagoneer with disc brakes
Outer stub
19 spline
9.94″ from end of splines to center of u-joint bore

from

$7.99

Replacement inner axle seal for Dana 44 (flanged axle) .Yukon Mighty seal.

Product Features:

Inner axle seal
Fits Dana Spicer 44 rear with flanged axle

from

$1016.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$429.99

Yukon hardcore drive flange kit for Dana 44, 19 spline outer stubs. Non-engraved caps..

Product Features:

Drive flange kit
Fits Dana Spicer 44 with 19 spline outer axles
Includes two drive flanges, two caps and all necessary hardware

from

$249.99

4340 Chrome Moly outer stub for GM truck & Blazer and Jeep Wagoneer with disc breakes. 19 spline, 9.94″. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

Fits Dana Spicer 44 in GM truck and Blazer and Jeep Wagoneer with disc brakes
4340 Chromoly
Outer stub
19 spline
9.94″ from end of splines to center of u-joint bore

from

$182.99

Replacement redi-sleeve yoke saver for Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 .Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits Dana Spicer 25, 27, 30, 4 and 50

from

$159.99

Yukon yoke for Model 20 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects. This yoke does not come with straps.

Product Features:

Fits AMC Model 20
28 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
Strap style

from

$125.99

Fits 1977-1991 Jeep Wagoneer
Includes axle bearings, races and seal
Services one side

Most Sold 1979 Jeep Wagoneer 4WD Components

Explore our best-selling Jeep parts for the 1979 Wagoneer among 3 OEM and aftermarket options starting from $116.99.

show more show less

from

$116.99

Black nylon reinforced fiberglass dial. Limited lifetime warranty. 19 spline, internal bolts. Chrome.

Product Features:

Black Nylon Reinforced Fiberglass Dial
Limited Lifetime Warranty

from

$204.99

Ultimate in style and service. Latest patented technology. Smooth operation. Limited lifetime warranty. 10 spline, 6 bolts. Chrome.

Product Features:

Ultimate In Style And Service
Latest Patented Technology
Smooth Operation
Limited Lifetime Warranty

from

$297.99

HUB 4X4-PREM MAN LCK

Top-Rated Drivetrains Brands For Your 1979 Jeep Wagoneer

Shop for the best-rated brands offering Drivetrains and other products for your 1979 Jeep Wagoneers. Below you’ll find some of our best rated Drivetrains from Spicer, Moog, and Driveworks, and more. Drivetrains from these brands that fit a 1979 Wagoneer start at just $6.99 and are rated as high as 4.6 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Spicer 1979 Jeep Wagoneer Drivetrains

When it comes to maintaining or upgrading your 1979 Jeep Wagoneer, using quality Drivetrains is essential to ensure durability and a perfect fit. Spicer ticks all of those boxes. We offer a wide selection of Spicer Drivetrains, specifically designed for the 1979 Jeep Wagoneer. With over 3 Spicer brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $31.99, with an average price of just $42.32. Plus, with over 21 customer reviews and an average rating of 4.6 stars, you can trust that our Spicer Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $55.99

(7)

Universal Joint

“Nice stub axle u-joint, perfect fit!”

from $31.99

(12)

Universal Joint, Greaseable 1310 Series OSR

“No problems with Installation and appears to be quality part! Great for my old School Street Car!”

from $38.99

(2)

Universal Joint

“I use this on a 4×4 off-road. It’s always a tough trade-off between the greaseable and non-greasable u-joints. The non-greaseable is stronger. The”

Popular Moog 1979 Jeep Wagoneer Drivetrains

Moog auto parts is one of the highest quality Drivetrain brands in the market. Any 1979 Jeep Wagoneer owner should feel confident when installing genuine Moog parts in their vehicle. To ensure the best fit and performance for your 1979 Wagoneer, Advance Auto Parts carries a full inventory of 3 Moog Drivetrains. Plus you will be keeping your Jeep in peak condition while saving money because prices on these Moog Drivetrains range from $23.99 to $36.99, plus, with more than 7 customer reviews and an impressive 4.5 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $23.99

(4)

Universal Joint U-Bolt Kit

“I used these to replace the factory originals that had over 80K miles on a 1964 Chevelle Malibu. I had a strange click in the differential area and s”

from $36.99

(1)

Greaseable Premium Universal Joint

“the u-joint itself fit fine however the grease fitting is too large for the hole provided in the u-joint. I had to enlarge the hole to fit the fitting”

from $26.99

(2)

Universal Joint Strap Kit

“Perfect fit great value”

FAQs for 1979 Jeep Wagoneer Drivetrains

Which Drivetrains are best-sellers for 1979 Jeep Wagoneers?

Out of 369 Drivetrains that fit 1979 Jeep Wagoneers, the following parts are the top sellers:

Greaseable Premium Universal Joint (10086900) – $35.99
Universal Joint (10265714) – $15.99
Non-Greaseable Super Strength Universal Joint (10086913) – $40.99

What’s the price range for 1979 Jeep Wagoneer Drivetrains?

Drivetrain prices for the 1979 Jeep Wagoneer start at $1.99 and go up to $1,566.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1979 Jeep Wagoneer?

The average price for Drivetrains for the 1979 Jeep Wagoneer is $179.36. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Jeep Wagoneer model years?

Yes, we currently carry Drivetrains for 29 model years of Jeep Wagoneers between 1963 and 2025. Drivetrains are bought most frequently for the following model years: 1990, 1989, 1988, 1987, 1986, 1985, 1984, 1983, and 1982.

What are the cheapest Drivetrains for my 1979 Jeep Wagoneer?

The cheapest 1979 Jeep Wagoneer Drivetrains we carry in stock are:

Ring Gear Bolt (19640279) – $1.99
OE Replacement, 12 Point Hex, 1/4 Inch – 28 X .625 Inch (50074782) – $1.99
Oem, For Use With Dana 300 Transfer Case/ Dana 20 Transfer Case (50074389) – $1.99
OE Replacement, 12 Point Hex, 1/4 Inch – 28 X 6.25 Inch (50074249) – $1.99
Differential Crush Sleeve (10592883) – $2.99

What are the top-rated Drivetrains that fit the 1979 Jeep Wagoneer?

Out of 856 reviews by customers, our 1979 Jeep Wagoneer Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1979 Jeep Wagoneer and their top-rated products:

Universal Joints
- Universal Joint Strap Kit (10086992) – $26.99
- Universal Joint (10265717) – $15.99
- Greaseable Premium Universal Joint (10086982) – $36.99
Spindles
- Universal Joint Strap Kit (10086992) – $26.99
- Universal Joint (10265717) – $15.99
- Greaseable Premium Universal Joint (10086982) – $36.99
4WD Components
- Universal Joint Strap Kit (10086992) – $26.99
- Universal Joint (10265717) – $15.99
- Greaseable Premium Universal Joint (10086982) – $36.99

What types of Drivetrains do you sell for my 1979 Jeep Wagoneer?

As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1979 Jeep Wagoneer:

Can I get help with 1979 Jeep Wagoneer Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Jeep Drivetrains and more.

What is your return policy for Jeep Wagoneer Drivetrains?

Advance Auto Parts keeps returns simple. For new Jeep Wagoneer Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1979 Jeep Wagoneer Drivetrains

Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)

Yukon Gear – Model 20 Axle End Play Shim (Part No.55061)

Yukon Gear – Replacement Redi-Sleeve Yoke Saver For Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 (Part No.30222)

Crown Auto Jeep Replacmnt – Oem, For Use With Dana 300 Transfer Case/ Dana 20 Transfer Case (Part No.J0939001)

Motive Gear – Differential Pinion Solid Spacer Kit w/Shims (Part No.4105)

Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 61 & 70U (Part No.55020)

National – Tapered Roller Bearing Cone (Part No.02872)

Crown Auto Jeep Replacmnt – For Use With Front Or Rear Yokes, Hex Head Bolt (Part No.4006698K)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)

Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41022)

Motive Gear – Differential Mini Spool (Part No.MSD44-30)

National – Shaft Repair Sleeve (Part No.99193)

Yukon Gear – Set Up Bearing (Part No.56039)

Yukon Gear – Steel Spool For Dana 60 With 35 Spline Axles, 4.10 & Down (Part No.32042)

Yukon Gear – Replacement Axle Stud For Dana 44 & Model 35 (Part No.33171)

Yukon Gear – Axle Bearing Retainer Plate For Dana 44 TJ Rear (Part No.33472)

Dorman – Help – Transfer Case Switch (Part No.49314)

Yukon Gear – Dana 50 Dana 60 Dana 70 & Dana 80 Roll Pin, 0.225" Dia, For X/P Shaft, 1.87" Lng (Part No.33327)

Yukon Gear – Standard Open Spider Gear Replacement Kit For Dana 25 And 27 With 10 Spline Axles (Part No.16069)

Yukon Gear – Grizzly Locker For Dana 60, 4.10 & Down, 40 Spline (Part No.28024)

MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.329-10)

Motive Gear – Differential Pinion Shim Kit (Part No.1127)

National – Multi Purpose Seal (Part No.1981)

Yukon Gear – High Performance Replacement Ring & Pinion Gear Set For Dana 60 In A 5.86 Ratio (Part No.24306)

Yukon Gear – Replacement Axle Bearing And Seal Kit For ’77 To ’91 Dana 44 And Jeep Wagoneer Front Axle (Part No.10033)

National – Multi-Purpose Seal (Part No.3946)

Yukon Gear – Dana 44 Outer Stub Axle Replacement (Part No.21108)

Driveworks – Taper Bearing Cup (Part No.S-15245)

Valvoline – MaxLife Multi-Vehicle Automatic Transmission Fluid, 1 Gallon (Part No.773775)

National – Bearing Race (Part No.JLM104910)

National – Shaft Repair Sleeve (Part No.99193)

Felpro – Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (Part No.RDS 6629)

National – Differential Pinion Seal (Part No.5778)

Motive Gear – Differential Pinion Nut (Part No.379570S)

Powertrax – No-Slip Traction System (Part No.9204302700)

Motive Gear – Differential Master Bearing Kit – Timken (Part No.R30RMKT)

Motive Gear – Differential Master Bearing Kit – Timken (Part No.RA28LRMKT)

Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)

Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)

Yukon Gear – Replacement Ring Gear Bolt For Model 35, Dana 25, 27, 30 & 44 – 3/8" X 24 (Part No.33038)

Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)

Yukon Gear – Replacement Ring Gear Bolt For Model 20, Grand Cherokee 35, "Super" Dana 30 & Dana 50 – 7/16" X 20 (Part No.33040)

Yukon Gear – Chrysler 9.25" And Dana 44 / 60 Tracloc Clutch Guide Replacement (Part No.33249)

Yukon Gear – 7/16" To 3/8" Ring Gear Bolt Spacer Sleeve. (Part No.33056)

Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)

Yukon Gear – Crush Sleeve (Part No.33085)

Yukon Gear – Replacement Carrier Shim Kit For Dana Spicer 44, 30 Spline Axles (Part No.55010)

Motive Gear – Ring Gear Bolt (Part No.D8OZ4216B)

Yukon Gear – Replacement Pinion Nut For Dana 25, 27, 30, 36, 44, 53 & GM 7.75" (Part No.33143)

Yukon Gear – Dana 25 / 27 / 30 / 36 / 44 / 50 Pinion Seal Replacement (Part No.30128)

Motive Gear – Differential Pinion Shim Kit (Part No.1104)

Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)

Spicer – Universal Joint, Greaseable 1310 Series OSR (Part No.5-153X)

MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.329-10)

Driveworks – Universal Joint (Part No.DW-315G)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.317)

Driveworks – Universal Joint (Part No.DW-380)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.318-10)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.371)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.377)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)

Driveworks – Universal Joint (Part No.DW-377)

Driveworks – Universal Joint (Part No.DW-369)

Driveworks – Universal Joint (Part No.DW-371)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.315G)

MOOG Driveline Products – Double Cardan CV Centering Yoke (Part No.607)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.380)

Dorman – Help – U-Joint Bolt Kit (Part No.81008)

Yukon Gear – 1310 & 1330 U/Joint Strap, Dana 30, Dana 44, Model 35, & 9.25" With Bolts (Part No.41195)

Crown Auto Jeep Replacmnt – Oem Replacement, 1.187 Inch Bearing Cap (Part No.J8126638)

Yukon Gear – Axle U/Joint For Dana 30, 44 & GM 8.5" Front (Part No.42018)

Yukon Gear – 1310 U/Joint With Zerk Fitting On Cross (Part No.42008)

Spicer – Universal Joint (Part No.5-789X)

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

National – Multi-Purpose Bearing (Part No.B-2110)

National – Multi-Purpose Seal (Part No.9449)

Driveworks – Taper Bearing Cup (Part No.S-15245)