1979 Chevrolet Camaro Performance Engines

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 70cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

This Spectre engine dress-up kit was designed for the 1987 – 1995 Chevy 305 & 350 engines. This kit includes: stock height valve covers, chrome valve cover T-bolts, chrome oil filler cap, chrome PCV breather, grommets, and an air cleaner adapter stud. The air filter adapter stud, is a z-bolt that is designed to allow you to use a center stud style air cleaner assembly instead of the stock dual-stud setup. Manufactured using high quality materials this kit features triple chrome plated parts.

Product Features:

• For 1987-1995 Chevrolet 305-350 engines
• Includes stock height valve covers & T-bolts
• Includes oil filler caps, pcv vent filter
• Includes air cleaner Z-Stud
• Chrome engine kit

Avoid trouble with this precision timing tape. Use it for accurate timing, setting valve lash or when degreeing the harmonic balancer.

Product Features:

• Accurate in calibration
• For hi-performance engines
• Increased performance
• Set valve lash at proper time

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Manufactured from a blend of nitrile rubber and fiber for excellent sealing and durability. Precision die cut for application.

Product Features:

• Edge molded rubber water outlet gasket is reusable
• Requires no gasket sealer
• Solid aluminum carrier for strength/rigidity

Product Features:

• Timing Chain Only

Grade 8, single bolt. Black plated finish. The washers are designed to secure the Mr. Gasket cam button pn1180, pn1181, and pn1183 or can be used as stock replacements.

Product Features:

• Specialty and drive train fastener
• Special cam bolts
• Black plated finish

Finish your custom engine job with these show quality grade 5 chromed bolts, includes AN washers which have no exposed shoulder for a professional appearance.

Product Features:

• Intake bolt kit
• Chrome plated
• Includes an type washers
• Ideal for street rods/machines

TIMING COVER SEAL

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

• Designed for 2500 to 6500 Performance
• Designed for Hi-Perf Street; Drag or Marine Use
• Matched to Edelbrock Torker II Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Dyno Matched/Street Proven Performance
• Take The Guesswork Out Of Camshaft Selection

This stud uses heat treated grade 8 alloy steel. The enlarged radius base provides extra strength for a more durable stable shank. Black plated finish. Fits Chevy small block and Ford small block.

Product Features:

• Heat-treated
• Grade 8 alloy steel
• Ex strength enlarged radius
• More durable/stable shank
• Prevents stud flexing
• Black plated finish

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Manufactured from cellulose and nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement, high performance street, drag race and oval track.

Product Features:

• Maxi-seal fiber material
• Superior blow-out resistance
• High-tensile strength
• Reduces gasket splitting
• Graphite non-wicking rubber
• No cork particles
• Easy removal for disassembly

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

Thick, molded rubber with steel carrier. Manufactured from high-density cork and rubber blend gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage. Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Available in standard or extra thick to provide additional valve train to cover clearance. For OE replacement, high performance street, drag race and oval track.

Product Features:

• Features nitrile rubber material for long life
• Molded rubber gaskets are reusable
• Ideal for engine requiring valve lash maintenance

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

Edelbrock part #9653 Pushrods are designed for Chevy 348/409 “W” series V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precis

Product Features:

• 7.2 in. Length
• 0.312 in. Diameter
• 4130 Chromoly Steel Material
• Black Oxide Finish
• Made In The USA

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered and manufactured specifically for repair applications
• Unsurpassed quality you can trust
• Validated for fit, form, and function

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered and manufactured specifically for repair applications
• Unsurpassed quality you can trust
• Validated for fit, form, and function

Features two threaded bosses for temp control switch satin finish.

Product Features:

• Emission System Water Outlet

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

• Fits Chevy engines
• Includes a 1/2 inch NPT threaded hole for by-pass hose
• Includes bolts
• Chrome plated
• Easy to install
• O-ring/gasket not included

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

• 2 in. adjustable range
• Includes necessary hardware
• Chrome plated
• Individually packaged