1978 Ford LTD Drivetrains

Popular 1978 Ford LTD Drivetrains Categories

Essential Drivetrains for 1978 Ford LTDs

Yukon Gear – Star Washers, 3.062" Ford 9" Drop Out New Design Only (Part No.32143)

Star Washers, 3.062" Ford 9" Drop Out New Design Only

from

$4.99
STAR washers, 3.062″ Yukon Ford 9″ Drop Out new design ONLY.

Product Features:
  • Star washer
  • Fits Ford 9″
  • 3.062″ designs only
See More

Yukon Gear – Master Overhaul Kit For Ford 9" Lm603011 Differential (Part No.14054)

Master Overhaul Kit For Ford 9" Lm603011 Differential

from

$299.99
Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses carrier bearings & races with an I.D. of 1.780″ and an O.D. of 3.062″. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:
  • Fits Ford 9″ with LM603011 carrier races
  • Included are Timken bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.
See More

Yukon Gear – Wheel Lug Stud (Part No.33571)

Wheel Lug Stud

from

$7.99
Wheel Lug Stud

Yukon Gear – Side Gear And Thrust Washer (0.875" Shaft) For 8.8" Ford (Part No.33300)

Side Gear And Thrust Washer (0.875" Shaft) For 8.8" Ford

from

$11.99
Side gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:
  • Side gear thrust washer for Ford 8.8″
  • 0.875″ diameter cross pin shaft applications only
See More

Yukon Gear – Standard Open Spider Gear Kit For 9" Ford With 31 Spline Axles And 4-Pinion Design (Part No.16034)

Standard Open Spider Gear Kit For 9" Ford With 31 Spline Axles And 4-Pinion Design

from

$317.99
Yukon standard open spider gear kit for 9″ Ford with 31 spline axles and 4-pinion design. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:
  • Spider gear kit
  • Fit Ford 9″ open differential with 31 spline axles
  • Includes two side gears, four pinion gears, cross pin shaft, roll pins and spider gear thrust washers.
See More

Yukon Gear – R1563Tav Rear Axle Bearing And Seal Kit (Part No.10004)

R1563Tav Rear Axle Bearing And Seal Kit

from

$42.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.

Product Features:
  • Includes axle bearing and seal
  • Services one side
  • Torrington Brand
  • 2.250″ O.D.
  • 1.400″ I.D.
See More

Yukon Gear – Grizzly Locker For Ford 8" With 31 Spline Axles (Part No.28007)

Grizzly Locker For Ford 8" With 31 Spline Axles

from

$941.99
The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:
  • Fits Ford 8″ with 31 spline axles
  • Patented internal design reduces common locker failures
  • 8620 internals for added strength
  • Assembled in the USA
See More

FAG US – BEARING CONE (Part No.KLM12749)

BEARING CONE

from

$13.29
BEARING CONE

National – Shaft Repair Sleeve (Part No.99193)

Shaft Repair Sleeve

from

$43.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

Felpro – Differential Cover Gasket (Part No.RDS 55393)

Differential Cover Gasket

from

$6.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Unsurpassed quality you can trust
  • Validated for fit, form and function
  • Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
See More

Dorman – Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (Part No.615-075.1)

Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In.

from

$3.29
This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)

Redline Synthetic "Shock Proof" Oil - 4 Quarts

from

$137.99
Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:
  • Includes four quarts of Redline Shockproof oil
See More

Yukon Gear – Extra HD 3.062" Nodular Iron Dropout For Ford 9" (Part No.32099)

Extra HD 3.062" Nodular Iron Dropout For Ford 9"

from

$615.99
Yukon Extra HD 3.062″ nodular Iron dropout for Ford 9″. Yukon nodular iron dropouts feature a 5/8″ cap bolt and forged caps for maximum strength. Rated up to 1200HP!

Product Features:
  • Fits Ford 9″
  • 3.062″ carrier race diameter
  • Nodular iron for added strength
See More

Yukon Gear – Pinion Install Kit For Ford 8.8" Differential (Part No.13041)

Pinion Install Kit For Ford 8.8" Differential

from

$167.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:
  • Fits 2009 and down Ford 8.8″
  • Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
See More

Yukon Gear – Trac Loc For Ford 9" Wtih 28 Spline Axles – Aggressive Design (Part No.26007)

Trac Loc For Ford 9" Wtih 28 Spline Axles - Aggressive Design

from

$821.99
The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:
  • Fits Ford 9″ with 28 spline axles
  • Trac Loc positraction
  • Clutch style positraction
  • Aggressive design
  • Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
  • Fully rebuildable
  • Assembled in the USA
See More

National – Shaft Repair Sleeve (Part No.99199)

Shaft Repair Sleeve

from

$37.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

Yukon Gear – Bearing Race Driver Set, 21 Piece (Part No.56030)

Bearing Race Driver Set, 21 Piece

from

$1566.99
21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:
  • Bearing race driver set
  • 21 pieces
  • All steel construction
See More

Yukon Gear – 3.062" Side Adjuster For Ford 9" (Part No.32139)

3.062" Side Adjuster For Ford 9"

from

$94.99
3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:
  • Side adjuster
  • Fits Ford 9″
  • 3.062″ designs only
See More

Yukon Gear – 8" Ford O-Ring (Part No.30027)

8" Ford O-Ring

from

$9.99
8″ Ford O-ring.

Product Features:
  • Pinion support o-ring
  • Fits Ford 8″
See More

Yukon Gear – Purple Aluminum Pinion Support For 9" Ford Daytona (Part No.32036)

Purple Aluminum Pinion Support For 9" Ford Daytona

from

$264.99
Product Features:
  • Fits Ford 9″ with 28 spline pinion
  • Larger inner pinion bearing reduces gear deflection under high load
  • Races installed
  • 6061 aluminum
  • Annodized purple
See More

Dorman – Standard Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (Sold by each) (Part No.615-074)

Standard Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (Sold by each)

from

$4.49
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

Driveshaft Flange Bolts

from

$20.29
This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Yukon Gear – 8" Ford Pinion Seal (Part No.30180)

8" Ford Pinion Seal

from

$24.99
8″ Ford pinion seal.Yukon Mighty seal.

Product Features:
  • Pinion seal
  • Fits Ford 8″
See More

FAG US – TAPERED ROLLER BEARI (Part No.KT45)

TAPERED ROLLER BEARI

from

$24.29
TAPERED ROLLER BEARI

Yukon Gear – Steel Spool For Ford 9" With 40 Spline Axles (Part No.32182)

Steel Spool For Ford 9" With 40 Spline Axles

from

$389.99
Yukon Performance 2-3/16″ deck steel spool for 9″ Ford with 40 spline axles. Spool uses 2″ journal bearings (45 degree). Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:
  • Fits Ford 9″ with 40 spline axles
  • Provides 100% traction to both wheels at all times
  • Not recommended for street driven vehicles
See More

Spicer – Universal Joint (Part No.5-1310X)

Universal Joint

from

$35.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More

Yukon Gear – Yoke For Ford 9" With 28 Spline Pinion And A 1330 U/Joint Size (Part No.41143)

Yoke For Ford 9" With 28 Spline Pinion And A 1330 U/Joint Size

from

$242.99
Yukon yoke for Ford 9″ with 28 spline pinion and a 1330 U/joint size. 5″ length. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:
  • Fits Ford 9″
  • 28 spline
  • 1330 u-joint size
  • Outside snap ring design
  • 3.625″ snap ring span
  • 1.125″ cap diameter
  • U-bolt style
See More

Yukon Gear – Pinion Support Bolt For 8" And 9" Ford (Part No.33242)

Pinion Support Bolt For 8" And 9" Ford

from

$6.99
Pinion support bolt for 8″ and 9″ Ford.

Product Features:
  • Pinion support bolt for Ford 8″ and 9″
  • 3/8″ x 24 thread
  • 1.0″ long
See More

Upgrade your 1978 Ford LTD with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1978 Ford LTD, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your LTD functioning at its best. At Advance Auto Parts, we offer a wide selection of 448 Drivetrains for the 1978 Ford LTD, designed to meet your needs without breaking the bank. From Differential replacements to Universal Joints upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1978 Ford LTD at great prices. Our Drivetrains inventory for this model ranges from just $1.99 to $1,566.99, with an average price of $250.72. Our 448 Drivetrains in stock come from 15 trusted brands, so you’re sure to find the right part for your 1978 Ford LTD without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1978 Ford LTD, we stock popular OEM and aftermarket Drivetrains from top names like Spicer, Moog, Driveworks, and more. Spicer Drivetrains start at just $28.99 and boast an impressive 5 stars average rating from customers. Moog and Driveworks also bring quality to the table, with Drivetrains available starting at $4.29, and at an average 4 stars rating. With 4,174 customer reviews and counting, our 1978 Ford LTD Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1978 Ford LTD is always ready to roll. We’re committed to providing you with everything you need to keep your LTD in top shape, all in one place. Start shopping confidently below for your 1978 Ford LTD!

Best-Selling Differentials for 1978 Ford LTDs

Enhance the driving experience in your Ford with 374 quality Differential components, starting at $1.99.

Felpro – Differential Carrier Gasket (Part No.RDS 55074)

Differential Carrier Gasket

from

$8.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Unsurpassed quality you can trust
  • Validated for fit, form and function
  • Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
See More

National – Multi Purpose Seal (Part No.7044NA)

Multi Purpose Seal

from

$15.79
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

Motive Gear – Differential Crush Sleeve (Part No.3507575)

Differential Crush Sleeve

from

$2.49


Product Features:
  • CRUSH SLEEVE 7.25 & 8.25 MIN ORDER 5000
See More

Powertrax – No-Slip Traction System (Part No.9206902800)

No-Slip Traction System

from

$551.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!
See More

Powertrax – Lock Right Locker (Part No.1830-LR)

Lock Right Locker

from

$444.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!
See More

National – Bearings (Part No.M802048)

Bearings

from

$23.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Motive Gear – Differential Pinion Nut (Part No.379570S)

Differential Pinion Nut

from

$6.49
All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!
See More

National – Wheel Bearing and Seal Kit (Part No.RA-311)

Wheel Bearing and Seal Kit

from

$169.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Spindle bearing and seal kit
  • Includes all components required to complete the repair
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Driveworks – Oil Seal (Part No.S-3604)

Oil Seal

from

$4.79
Value-priced seal meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Driveworks – Oil Seal (Part No.S-7044NA)

Oil Seal

from

$4.29
Value-priced seal meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)

3 Qt - 80W90 Conventional Gear Oil With Posi Additive

from

$57.99
3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:
  • Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive
See More

Dorman – Help – Pinion Crush Sleeves (Part No.81056)

Pinion Crush Sleeves

from

$5.99
This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:
  • Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles.
  • Required replacement – when servicing the differential
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Driveworks – Tapered Roller Bearing (Part No.S-M-802048)

Tapered Roller Bearing

from

$16.99
Product Features:
  • Brand may vary by location
See More

Yukon Gear – Crush Sleeve (Part No.33093)

Crush Sleeve

from

$10.99
Crush Sleeve for Model 35, Chrysler 7.25″, 8.25″ Ford 8″ & GM 7.75″. Approx 0.495″ long.

Product Features:
  • Crush sleeve for AMC Model 35, Chrysler 7.25″ and 8.25″, Ford 8″ and GM 7.75″
  • 0.495″ tall
See More

Yukon Gear – Crush Sleeve (Part No.33085)

Crush Sleeve

from

$9.99
Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:
  • Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
  • 0.480″ tall
See More

Yukon Gear – Outer Oil Slinger For Ford 7.5", 8.8", 9", 10.25" (Part No.33022)

Outer Oil Slinger For Ford 7.5", 8.8", 9", 10.25"

from

$8.99
Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:
  • Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear
See More

Yukon Gear – Ford 8" & 9" Standard Open, Ag, & Detroit Locker Ring Gear Bolt (Part No.33058)

Ford 8" & 9" Standard Open, Ag, & Detroit Locker Ring Gear Bolt

from

$5.99
Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt. 7/16″ head, .925″ long.

Product Features:
  • Ring gear bolt for Ford 8″ and 9″
  • For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
  • 7/16″ head
  • .925″ long
See More

Yukon Gear – Ford 8" & 9" Standard Open, Ag, & Detroit Locker Ring Gear Bolt (Part No.33043)

Ford 8" & 9" Standard Open, Ag, & Detroit Locker Ring Gear Bolt

from

$5.99
Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt, 1.0″ long, Ford.

Product Features:
  • Ring gear bolt for Ford 8″ and 9″
  • For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
  • 1.0″ long
See More

Yukon Gear – Ford 8" & 9" Tracloc Ring Gear Bolt (Part No.33044)

Ford 8" & 9" Tracloc Ring Gear Bolt

from

$4.99
Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.

Product Features:
  • Ring gear bolt for Ford 8″ and 9″
  • For use with Trac Loc limited slip
  • 1.25″ long
See More

Motive Gear – Ring Gear Bolt (Part No.D8OZ4216B)

Ring Gear Bolt

from

$1.99


Product Features:
  • BOLT 9″ FORD OPEN R.G. SAME AS M-4216A200
See More

Yukon Gear – Pinion Nut (Part No.33154)

Pinion Nut

from

$7.99
Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:
  • Pinion nut for Ford 7.5″, 8″ and 9″
  • 3/4″ x 20 thread
  • 1 1/6″ socket
See More

Yukon Gear – 9" Ford Gasket (Part No.23012)

9" Ford Gasket

from

$11.99
9″ Ford gasket.

Product Features:
  • Dropout gasket
  • Fits Ford 9″
See More

Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)

Redline Synthetic "Shock Proof" Oil With Positraction Additive - 4 Quarts

from

$148.99
Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:
  • Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive
See More

Yukon Gear – Preload Shim Kit For Chrysler 8.75" & Ford 9" (Part No.55030)

Preload Shim Kit For Chrysler 8.75" & Ford 9"

from

$21.99
8.75″ Chrysler & 9″ Ford preload shim kit.

Product Features:
  • Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing
See More

Yukon Gear – Dana 44, Ford 8" / 9", And Model 20 Side Gear Thrust Washer Replacement (Part No.33283)

Dana 44, Ford 8" / 9", And Model 20 Side Gear Thrust Washer Replacement

from

$5.99
Product Features:
  • Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
  • 0.030″ thick
See More

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)

Redline Synthetic "Shock Proof" Oil - 3 Quarts

from

$99.99
Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:
  • Includes three quarts of Redline Shockproof oil
See More

Yukon Gear – Pilot Bearing For Ford 9" (Part No.18042)

Pilot Bearing For Ford 9"

from

$38.99
8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:
  • Pilot bearing
  • Fits Ford 9″
  • 0.656″ thick
See More

Yukon Gear – Pinion Support Bolt For 8" And 9" Ford (Part No.33242)

Pinion Support Bolt For 8" And 9" Ford

from

$6.99
Pinion support bolt for 8″ and 9″ Ford.

Product Features:
  • Pinion support bolt for Ford 8″ and 9″
  • 3/8″ x 24 thread
  • 1.0″ long
See More

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)

Redline Synthetic "Shock Proof" Oil - 4 Quarts

from

$137.99
Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:
  • Includes four quarts of Redline Shockproof oil
See More

Yukon Gear – 1310 And 1330 U/Bolt Kit (2 U-Bolts And 4 Nuts) For 9" Ford (Part No.41112)

1310 And 1330 U/Bolt Kit (2 U-Bolts And 4 Nuts) For 9" Ford

from

$18.99
1310 and 1330 U/bolt kit (2 U-bolts and 4 nuts) for 9″ Ford.

Product Features:
  • u-joint u-bolt kit
  • Fits Ford 9″
  • 1310 and 1330 u-joint size
  • Includes two u-bolts and four nuts
See More

Yukon Gear – O-Ring For 9" Ford (Part No.30028)

O-Ring For 9" Ford

from

$14.99
O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:
  • Pinion support o-ring
  • Fits Ford 9″
See More

Yukon Gear – Side Gear With Hub For 9" Ford With 31 Splines (Part No.16161)

Side Gear With Hub For 9" Ford With 31 Splines

from

$47.99
Side gear with hub for 9″ Ford with 31 splines.

Product Features:
  • Side gear with hub
  • Fits Ford 8″ and 9″ standard open differential and Trac Loc positraction with 31 spline axles
See More

Yukon Gear – Pinion Seal For ’61-’85 9" Ford (Part No.30137)

Pinion Seal For '61-'85 9" Ford

from

$17.99
Pinion seal for ’61-’85 9″ Ford. 3″ OD.Yukon Mighty seal.

Product Features:
  • Pinion seal
  • Fits 1961-1985 Ford 9″
  • 3.00″ O.D.
See More

Yukon Gear – 8" Ford O-Ring (Part No.30027)

8" Ford O-Ring

from

$9.99
8″ Ford O-ring.

Product Features:
  • Pinion support o-ring
  • Fits Ford 8″
See More

Yukon Gear – Pilot Bearing Retainer For Ford 9" (Part No.33255)

Pilot Bearing Retainer For Ford 9"

from

$11.99
Pilot bearing retainer for Ford 9″.

Product Features:
  • Pilot bearing retainer for Ford 9″
See More

Yukon Gear – Ford 9" Nodular Daytona Style Pinion Support (Part No.32164)

Ford 9" Nodular Daytona Style Pinion Support

from

$175.99
Product Features:
  • Fits Ford 9″ with 28 spline pinion
  • Larger inner pinion bearing reduces gear deflection under high load
  • Nodular iron
  • Does not include races
See More

Dorman – Differential Pinion Yoke Assembly (Part No.697-530)

Differential Pinion Yoke Assembly

from

$135.99
Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:
  • Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
  • Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
  • Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
  • Validated fit – this differential end yoke has been tested to confirm accurate fit
See More

Dorman – Differential Pinion Yoke Assembly (Part No.697-539)

Differential Pinion Yoke Assembly

from

$125.99
Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:
  • Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
  • Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
  • Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
  • Validated fit – this differential end yoke has been tested to confirm accurate fit
See More

Yukon Gear – Short Yoke For Ford 9" HD With 28 Spline Axles And A 1330 U/Joint Size (Part No.41053)

Short Yoke For Ford 9" HD With 28 Spline Axles And A 1330 U/Joint Size

from

$121.99
Yukon short yoke for Ford 9″ HD with 28 spline axles and a 1330 U/joint size. 4″ length. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:
  • Fits Ford 9″
  • 28 spline
  • 1330 u-joint size
  • 3.625″ snap ring span
  • 1.125″ cap diameter
  • Outside snap ring design
  • U-bolt style
See More

Motive Gear – Differential Gear Install Kit (Part No.F9IK)

Differential Gear Install Kit

from

$33.99
Product Features:
  • MINI INSTALL KIT FORD 9″
See More

Yukon Gear – Pinion Depth Shims For Ford 8" (Part No.55055)

Pinion Depth Shims For Ford 8"

from

$31.99
8″ Ford pinion shim kit.

Product Features:
  • Pinion depth shims for Ford 8″
See More

Motive Gear – Differential Pinion Shim Kit (Part No.WAA4663)

Differential Pinion Shim Kit

from

$15.99
All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!
See More

Motive Gear – Differential Pinion Solid Spacer Kit w/Shims (Part No.4104)

Differential Pinion Solid Spacer Kit w/Shims

from

$10.49


Product Features:
  • SOLID SPACER FORD 8.8″ & 9″
See More

Yukon Gear – 8" Dropout Housing Gasket (Part No.23010)

8" Dropout Housing Gasket

from

$11.99
8″ dropout housing gasket.

Product Features:
  • Dropout gasket
  • Fits Ford 8″
See More

Driveworks – Tapered Roller Bearing (Part No.S-LM-603012)

Tapered Roller Bearing

from

$6.79
Product Features:
  • Brand may vary by location
See More

Motive Gear – Performance Differential Ring and Pinion (Part No.F880340)

Performance Differential Ring and Pinion

from

$272.99


Product Features:
  • R&P FORD 8″ – 3.40 RATIO
See More

Motive Gear – Differential Ring and Pinion (Part No.F9-370)

Differential Ring and Pinion

from

$222.99


Product Features:
  • FRD 10BL 9.0 R/P 3.70 MG
See More

Dorman – Differential Ring And Pinion Set (Part No.697-816)

Differential Ring And Pinion Set

from

$315.99
This differential ring and pinion directly replaces the original equipment on specific vehicle years, makes and models.

Product Features:
  • Direct replacement – this ring and pinion set matches the fit and function of the original components on certain vehicle applications.
  • Effective fix – eliminates grinding and whining from failed original bearings.
  • Thoroughly tested – vehicle try-on testing and rigorous quality control measures ensure longevity
  • Trustworthy quality – backed by team of designers and engineers in the United States
See More

Most Popular 1978 Ford LTD Universal Joints

Customize your Ford with 40 Universal Joints products like U-Joints, U-Joint Strap Kits, and U-Joint U-Bolt Kits, all priced under $111.99.

Spicer – Universal Joint (Part No.5-153X)

Universal Joint

from

$28.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More

Spicer – Universal Joint (Part No.5-213X)

Universal Joint

from

$39.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More

MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.534-10)

Universal Joint U-Bolt Kit

from

$11.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:
  • For U-Joints 375, 430, 434 & 498
  • Fits 1-1/8″ bearings
See More

Brute Force – Universal Joint (Part No.2-4900BF)

Universal Joint

from

$6.79
Universal Joint – Brute Force
See More

Neapco – Universal Joint (Part No.1-0025)

Universal Joint

from

$2.59
Universal Joint Strap Kit
See More

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354)

Greaseable Premium Universal Joint

from

$25.99
Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
  • KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
  • Cross forging shape and flash provide easier installation and high strength
See More

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)

Greaseable Premium Universal Joint

from

$19.99
Backed by superior materials and rigorous testing, MOOG Heavy Duty universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
  • STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
  • INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
  • RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
See More

Driveworks – Universal Joint (Part No.DW-354)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)

Non-Greaseable Super Strength Universal Joint

from

$32.99
Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
  • STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
See More

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)

Non-Greaseable Super Strength Universal Joint

from

$32.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)

Greaseable Super Strength Universal Joint

from

$32.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

Driveworks – Universal Joint (Part No.DW-434)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

Driveworks – Universal Joint (Part No.DW-369)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)

Greaseable Super Strength Universal Joint

from

$36.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.434)

Greaseable Premium Universal Joint

from

$25.99
Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
  • KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
  • Cross forging shape and flash provide easier installation and high strength
See More

Dorman – Help – U-Joint Bolt Kit (Part No.81004)

U-Joint Bolt Kit

from

$6.29
This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:
  • Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles.
  • Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
  • Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Neapco – Universal Joint (Part No.2-4801)

Universal Joint

from

$7.89
Universal Joint
See More

Neapco – Universal Joint (Part No.2-4800)

Universal Joint

from

$4.59
Universal Joint
See More

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.430)

Greaseable Premium Universal Joint

from

$26.99
Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
  • KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
  • Cross forging shape and flash provide easier installation and high strength
See More

Driveworks – Universal Joint (Part No.DW-270)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

Brute Force – Universal Joint (Part No.2-4800BF)

Universal Joint

from

$5.49
Universal Joint – Brute Force
See More

Neapco – Universal Joint (Part No.1-5900)

Universal Joint

from

$5.29
Universal Joint
See More

Spicer – Universal Joint (Part No.5-1330X)

Universal Joint

from

$37.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.265)

Greaseable Super Strength Universal Joint

from

$30.99
Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
  • STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
See More

Spicer – Universal Joint (Part No.5-1204X)

Universal Joint

from

$36.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More

Spicer – Universal Joint (Part No.5-7438X)

Universal Joint

from

$46.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More

Yukon Gear – 1310 U/Joint With Zerk Fitting On Cross (Part No.42008)

1310 U/Joint With Zerk Fitting On Cross

from

$44.99
Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.
See More

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.264)

Non-Greaseable Super Strength Universal Joint

from

$30.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

1310 To 1330 Adapter U/Joint

from

$59.99
Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.
See More

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.230)

Non-Greaseable Super Strength Universal Joint

from

$27.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

Yukon Gear – 1350 To 1410 Conversion U/Joint (Part No.42006)

1350 To 1410 Conversion U/Joint

from

$78.99
Yukon 1350 to 1410 conversion u/joint.
See More

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.255)

Greaseable Super Strength Universal Joint

from

$27.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

Yukon Gear – 1310 To Mechanics 3R Adapter U/Joint (Part No.42013)

1310 To Mechanics 3R Adapter U/Joint

from

$109.99
Yukon 1310 to Mechanics 3R adapter U/Joint.
See More

Yukon Gear – 1350 Lifetime Series U/Joint (Part No.42021)

1350 Lifetime Series U/Joint

from

$63.99
Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.
See More

Yukon Gear – 1350 U/Joint With Zerk Fitting (Part No.42010)

1350 U/Joint With Zerk Fitting

from

$51.99
Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.
See More

Yukon Gear – 1310 Lifetime U/Joint (Part No.42003)

1310 Lifetime U/Joint

from

$57.99
1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.
See More

Yukon Gear – 1350 To Mechanics 3R Adaptor U/Joint (Part No.42001)

1350 To Mechanics 3R Adaptor U/Joint

from

$111.99
Yukon 1350 to Mechanics 3R adaptor U/joint.
See More

Spicer – Universal Joint (Part No.5-1330-1X)

Universal Joint

from

$36.99
Universal Joint

Spicer – Universal Joint (Part No.5-7439X)

Universal Joint

from

$29.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More

Neapco – Universal Joint (Part No.2-4900)

Universal Joint

from

$4.19
Universal Joint
See More

Top Picks for 1978 Ford LTD Drive Shafts and Axles

Upgrade Ford LTDs with top-quality Drive Shafts and Axles parts, including 23 OEM and aftermarket selections for your 1978 model.

Driveworks – Oil Seal (Part No.S-8660S)

Oil Seal

from

$5.49
Value-priced seal meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

Driveshaft Flange Bolts

from

$20.29
This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Spicer – Universal Joint (Part No.5-1310X)

Universal Joint

from

$35.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More

Driveworks – Axle Repair Bearing (Part No.S-RP-5707)

Axle Repair Bearing

from

$16.49
Value-priced bearing meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

National – Bearings (Part No.307-L)

Bearings

from

$37.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Yukon Gear – Outer Axle Seal For 8" Ford (Part No.30031)

Outer Axle Seal For 8" Ford

from

$43.99
Outer axle seal for 8″ Ford.Yukon Mighty seal.

Product Features:
  • Outer axle seal
  • Fits Ford 8″
See More

Yukon Gear – Fill Plug For Ford 9", 1/2" Thread (Part No.33539)

Fill Plug For Ford 9", 1/2" Thread

from

$10.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:
  • Fill plug
  • Fits Ford 9″
See More

Yukon Gear – Tapered Axle Bearing And Seal Kit, 3.150" Od, For 9" Ford (Part No.10058)

Tapered Axle Bearing And Seal Kit, 3.150" Od, For 9" Ford

from

$111.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Tapered axle bearing and seal kit, 3.150″ OD, for 9″ Ford. This axle bearing & seal kit services one side only.

Product Features:
  • Axle bearing and seal kit for Ford 9″ rear
  • Includes axle bearing and seal
  • Tapered roller design
  • 3.150″ O.D.
  • 1.562″ I.D.
  • Services one side
See More

Yukon Gear – Axle Bearing Retainer For Ford 9", Large Bearing, 1/2" Bolt Holes (Part No.33467)

Axle Bearing Retainer For Ford 9", Large Bearing, 1/2" Bolt Holes

from

$67.99
Product Features:
  • Axle bearing retainer for Ford 9″
  • Fits large bearing applications
  • 1/2″ bolt holes
  • 3 1/2″ x 2 3/8″ bolt pattern
See More

Yukon Gear – The Carrier Bearing Puller (Part No.56072)

The Carrier Bearing Puller

from

$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:
  • Carrier bearing puller
  • Works with an impact gun to safely and easliy remove carrrier bearings
See More

Yukon Gear – Outer Axle Seal For Set 20 Bearing (Part No.30030)

Outer Axle Seal For Set 20 Bearing

from

$14.99
Outside seal (included in TK set20).Yukon Mighty seal.

Product Features:
  • Outer axle seal
  • Works with Set20 bearing
See More

Yukon Gear – Axle Bearing For 9" Ford (Part No.10057)

Axle Bearing For 9" Ford

from

$132.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing for 9″ Ford. 1.531″ I.D., 3.150″ O.D. This axle bearing & seal kit services one side only.

Product Features:
  • Axle bearing for Ford 9″
  • Sealed design
  • 3.150″ O.D.
  • 1.531″ I.D.
  • Services one side
See More

Yukon Gear – Conversion Bearing For Small Bearing Ford 9" Axle In Large Bearing Housing (Part No.18046)

Conversion Bearing For Small Bearing Ford 9" Axle In Large Bearing Housing

from

$92.99
Conversion bearing for small bearing Ford 9″ axle in large bearing housing.

Product Features:
  • Axle bearing
  • Fits Ford 9″
  • Conversion bearing to install small bearing axle into large bearing housing
  • 3.150″ O.D.
  • 1.377″ I.D.
See More

Yukon Gear – 1.250" Pinion Adaptor Sleeve (Stock Pinion Into Large Support) (Part No.32239)

1.250" Pinion Adaptor Sleeve (Stock Pinion Into Large Support)

from

$74.99
1.250″ pinion adaptor sleeve (stock pinion into large support).

Product Features:
  • Adapter sleeve
  • Fits Ford 9″
  • Adapts 28 spline pinion into 35 spline pinion support
See More

Yukon Gear – Adaptor Washer For 28 Spline Pinion In Oversize Support, For 9" Ford (Part No.32240)

Adaptor Washer For 28 Spline Pinion In Oversize Support, For 9" Ford

from

$71.99
Adaptor washer for 28 spline pinion in oversize support, for 9″ Ford.

Product Features:
  • Adapter washer
  • Fits Ford 9″
  • Adapts 28 spline pinion into 35 spline pinion support
See More

FAG US – AXLE SHAFT REPAIR BE (Part No.DR0148K)

AXLE SHAFT REPAIR BE

from

$64.99
AXLE SHAFT REPAIR BE

Spicer – SPICER U-JOINT (Part No.5-1310-1X)

SPICER U-JOINT

from

$44.99
SPICER U-JOINT

FAG US – AXLE BEARING (Part No.FC67147)

AXLE BEARING

from

$36.49
AXLE BEARING

Yukon Gear – Axle Bearing Retainer For Ford 9", Small Bearing, 3/8" Bolt Holes (Part No.33468)

Axle Bearing Retainer For Ford 9", Small Bearing, 3/8" Bolt Holes

from

$22.99
Product Features:
  • Axle bearing retainer for Ford 9″
  • Fits small bearing applications
  • 3/8″ bolt holes
  • 3 5/16″ x 2″ bolt pattern
See More

Yukon Gear – Axle Bearing Retainer For Ford 9", Large & Small Bearing, 3/8" Bolt Holes (Part No.33466)

Axle Bearing Retainer For Ford 9", Large & Small Bearing, 3/8" Bolt Holes

from

$22.99
Product Features:
  • Axle bearing retainer for Ford 9″
  • Fits large and small bearing applications
  • 3/8″ bolt holes
  • 3 9/16″ x 2″ bolt pattern
See More

FAG US – CONE (Part No.KL68149)

CONE

from

$13.99
CONE

Yukon Gear – Model 20 & Model 35 Axle Stud 1/2"-20 X 1.625" Length, 0.620" Dia – Knurl (Part No.33181)

Model 20 & Model 35 Axle Stud 1/2"-20 X 1.625" Length, 0.620" Dia - Knurl

from

$5.99
Model 20 & Model 35 axle stud 0.620″ Dia. Shank.

Product Features:
  • Axle stud for AMC Model 20 and Model 35
  • 1/2″ x 20 thread
  • 0.620″ knurl diameter
  • 1.625″ long
See More

FAG US – SHAFT SEAL (Part No.SS2468)

SHAFT SEAL

from

$5.19
SHAFT SEAL

In-Demand Transfer Cases for 1978 Ford LTDs

Select from 6 premium Transfer Cases parts for your 1978 Ford LTD, with prices ranging from $8.49 to $37.99.

National – Bearings (Part No.M88048)

Bearings

from

$15.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

National – Bearings (Part No.M88010)

Bearings

from

$10.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

National – Shaft Repair Sleeve (Part No.99199)

Shaft Repair Sleeve

from

$37.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

Driveworks – Tapered Cup Wheel Bearing Assembly (Part No.S-LM-102910)

Tapered Cup Wheel Bearing Assembly

from

$8.49
Value-priced bearing meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

FAG US – BEARING CONE (Part No.KLM12749)

BEARING CONE

from

$13.29
BEARING CONE

FAG US – CUP (Part No.M88010)

CUP

from

$11.29
CUP

Most Sold 1978 Ford LTD Spindles

Explore our best-selling Ford parts for the 1978 LTD among 5 OEM and aftermarket options starting from $1.99.

Dorman – Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (Part No.615-075.1)

Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In.

from

$3.29
This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Dorman – Standard Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (Sold by each) (Part No.615-074)

Standard Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (Sold by each)

from

$4.49
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Dorman – Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (sold by each) (Part No.615-075)

Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (sold by each)

from

$6.99
This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Dorman – Spindle Washer – I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-013.1)

Spindle Washer - I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In.

from

$4.29
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Dorman – Spindle Washer – I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In. (sold by each) (Part No.618-013)

Spindle Washer - I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In. (sold by each)

from

$1.99
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Top-Rated Drivetrains Brands For Your 1978 Ford LTD

Shop for the best-rated brands offering Drivetrains and other products for your 1978 Ford LTDs. Below you’ll find some of our best rated Drivetrains from Spicer, Moog, and Driveworks, and more. Drivetrains from these brands that fit a 1978 LTD start at just $4.29 and are rated as high as 5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Spicer 1978 Ford LTD Drivetrains

When it comes to maintaining or upgrading your 1978 Ford LTD, using quality Drivetrains is essential to ensure durability and a perfect fit. Spicer ticks all of those boxes. We offer a wide selection of Spicer Drivetrains, specifically designed for the 1978 Ford LTD. With over 9 Spicer brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $28.99, with an average price of just $37.66. Plus, with over 19 customer reviews and an average rating of 5 stars, you can trust that our Spicer Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

Universal Joint
from
$37.99
This product is not rated

Universal Joint

“”

Universal Joint
from
$46.99
This product is not rated

Universal Joint

“”

Universal Joint
from
$36.99
This product is not rated

Universal Joint

“”

Popular Moog 1978 Ford LTD Drivetrains

Moog auto parts is one of the highest quality Drivetrain brands in the market. Any 1978 Ford LTD owner should feel confident when installing genuine Moog parts in their vehicle. To ensure the best fit and performance for your 1978 LTD, Advance Auto Parts carries a full inventory of 13 Moog Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these Moog Drivetrains range from $11.99 to $36.99, plus, with more than 367 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

Non-Greaseable Super Strength Universal Joint
from
$30.99
This product is not rated

Non-Greaseable Super Strength Universal Joint

“”

Non-Greaseable Super Strength Universal Joint
from
$27.99
This product is not rated

Non-Greaseable Super Strength Universal Joint

“”

Greaseable Super Strength Universal Joint
from
$30.99
This product is not rated

Greaseable Super Strength Universal Joint

“”

FAQs for 1978 Ford LTD Drivetrains

Which Drivetrains are best-sellers for 1978 Ford LTDs?

Out of 448 Drivetrains that fit 1978 Ford LTDs, the following parts are the top sellers:

What’s the price range for 1978 Ford LTD Drivetrains?

Drivetrain prices for the 1978 Ford LTD start at $1.99 and go up to $1,566.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1978 Ford LTD?

The average price for Drivetrains for the 1978 Ford LTD is $250.72. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford LTD model years?

Yes, we currently carry Drivetrains for 26 model years of Ford LTDs between 1965 and 1991. Drivetrains are bought most frequently for the following model years: 1991, 1990, 1989, 1988, 1987, 1986, 1985, 1984, and 1983.

What are the cheapest Drivetrains for my 1978 Ford LTD?

The cheapest 1978 Ford LTD Drivetrains we carry in stock are:

What are the top-rated Drivetrains that fit the 1978 Ford LTD?

Out of 4,174 reviews by customers, our 1978 Ford LTD Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1978 Ford LTD and their top-rated products:

Can I get help with 1978 Ford LTD Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford LTD Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford LTD Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.